MicroBoards Orbit 3 - Manuals

Page 3 - TABLE OF CONTENTS

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 3 TABLE OF CONTENTS System Overview ............................................................................................................................. 5 Unpacking your system .................................................................................

Page 5 - System Overview

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 5 System Overview The Orbit 3 employs 2 general purpose DVD-+R/DL recorders, along with a single DVD reader. A hard drive also comes standard with the system, allowing for DVD/CD image archival and CD track extraction for CD audio compilations. An intuitive, menu ...

Page 6 - Installation Requirements; System; Power supply

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 6 Installation Requirements System Setup • Connect the power cable to the Orbit 3 duplicator and plug in to a protected power outlet strip or UPS power supply. • Turn on power to the duplicator. • Install the Input Rods and Output Bin. The system is now ready to u...

Page 7 - Orbit 3 Operation; Loading Discs; Rejected Discs

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 7 Orbit 3 Operation The Output Bin The Output bin should be installed prior to operating the Orbit 3. 1. Remove the 2 thumbscrews on the front of the Orbit 3. 2. Attach the Output Bin to the front of the Orbit 3 using the 2 thumbscrews. 3. Slide the Output Spindle...

Page 8 - Main Menu; Copy

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 8 COPY 4.0GB DVD 25% Main Menu The Up and Down Arrow buttons ( ▲▼ ) allow you to navigate through the menu without selecting the current menu item. The NO button will move you to the next menu item. YES will select the current menu item. Copy The source of the mas...

Page 10 - Compare; Batch Copy

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 10 Master 1 Master 2 Blanks Copy & Compare Copy and Compare mode will run a comparison of the Master and the new copies prior to unloading the recorder drives. Like Copy mode, the source of the master will depend on the System Setup selections. The same steps ...

Page 11 - Error status in Track Extraction:

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 11 INSERT MASTER DISC COPY START (HDD to DISC) HDD(01)? CD-DA 79:28 HDD(02)? FREE 2. You will now select the hard drive partition to which you would like to save the extracted tracks. The display will show each partition on the hard drive in turn and what is saved...

Page 12 - Setup Menu

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 12 Setup Menu Yes Yes SYSTEM SETUP MASTER SELECT? Yes Caption indicates button to press Display sequence ▲ (Back), NO, or ▼ (Forward) YES or ESC to return to Menu KEY Yes BURN DISC? CD WRITE? 48X CD? 40X CD? 4X CD? DVD WRITE? 16X DVD? 12X DVD? 1X DVD? USE BUZZER? ...

Page 13 - Accessing the Setup Menu

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 13 Accessing the Setup Menu 1. At the COPY START? (DISC to DISC) menu, press the NO , ▼ , or ▲ buttons until the display shows SYSTEM SETUP? SYSTEM SETUP? 2. Press the YES button 3. Pressing the NO or ▼ button will allow you to navigate through the menu. 4. Pressi...

Page 14 - Drive Status; Specifications

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 14 Drive Status This option allows you to disable a drive, if necessary. Any disabled drive will be bypassed during the duplication process; no discs will be loaded to or burned in a disabled drive. The recorder drives are numbered from the bottom up. There are 3 ...

Page 15 - Technical Support

Orbit 3 MICROBOARDS TECHNOLOGY, LLC 15 Technical Support For technical questions or support issues, contact Microboards Technology technical support: United States PH: 952-556-1639 FAX: 952-556-1628 [email protected] www.microboards.com Europe PH: +44 (0) 845 230 7800 www.microboards.co.uk Jap...