MicroBoards QD-2 - Manual - manualsarea.com

Page 3 - Table of Contents

3 Table of Contents Introduction ...................................................................................................................................... 5 Unpacking your system ...............................................................................................................

Page 6 - Basic Instructions; Buttons and LCD; Hardware Description; Reader Drive

6 Basic Instructions Buttons and LCD There are four buttons and an LCD on the front panel of the QD-52 duplicator. LED display: Shows the menu items and any status messages that may come up during operation. ENT button: The ENT button, used to start a duplication process or enter into an area in the...

Page 7 - Copying – 52x

7 The QD-52 system consists of a CD reader, CD Writer and Controller module. The master discs always go into the TOP CD Reader drive. The blank CD media will always go into the BOTTOM CD Recorder drive. The power switch and power LED are also located on the front of the QD-52 duplicator. The LCD dis...

Page 8 - Main Menu

8 Main Menu 1.0 Copy 2.0 Test 3.0 Test & Copy 4.0 Verify 5.0 Compare 6.0 Prescan 7.0 Disc Info 8.0 Edit Track 9. Setup Source Disc Analyzing…. Copying – 52x 17%150.4MB 01:15 1.0 Copy OK: 01 ESC Load Next Blank Disc ENT Source Disc Analyzing…. Testing – 52x 17% 150.4MB 01:15 2.0 Test OK: 01 ESC L...

Page 9 - Functions; Copy

9 1. Copy Copying – 52x 18% 150.4MB 01:15 2. Test Testing – 52x 18% 150.4MB 01:15 3. Test & Copy Testing – 52x 18% 150.4MB 01:15 1.0 Copy OK: 01 2.0 Test OK: 01 Functions There are 9 different functions for the QD-52 duplicator: Copy, Test, Test & Copy, Verify, Compare, Prescan, Disc Info, E...

Page 11 - CD to CD Edit

11 Scaning – 24x 15% 620.4MB 02:15 PreScan OK! 7. Disc Info Source Disc (Analyzing) 8. Edit Track 8-01. Edit Track CD to CD Edit Select Track: 1/16 04:53 Select Track: + 1/16 04:53 Select Track: End 1Track 04:53 Place the master disc into the TOP reader drive and press ENT. The prescan starts and th...

Page 12 - Play Audio Track

12 End Edit Disc And burn? YES Copying – 52x Edit 1/16 → 1/1 Burn Complete! OK: 01 Continue Edit Next disc? NO Continue Edit Next disc? NO Close all disc’s Sessions? Yes Closing Session Please wait…. Close Complete OK: 01 Fail: 01 8. Edit Track 8-01. Edit Track CD to CD Edit This screen shows the to...

Page 13 - Close Session

13 8-02. Edit Track Play Audio Track Select Track: 1/16 04:53 8. Edit Track 8-01. Edit Track CD to CD Edit 8-03. Edit Track Close Session Close all disc’s Sessions? Yes Closing Session Please wait…. Close Complete OK: 01 Fail: 01 Press the ▼ button until the display reads: Press the ENT button. The ...

Page 14 - Setup

14 Setup 9.Setup 9-01. Setup Language 9-02. Setup Burn Speed 9-03. Setup Read Speed 9-04. Setup Auto Start Drive 9-05. Setup Start Up Menu 9-06. Setup Auto Verify 9-07. Setup Auto Compare 9-08. Setup Auto Prescan 9-09. Setup Eject Disc 9-10. Setup Burn Mode 9-11. Setup Display Time 9-12. Setup Butto...

Page 17 - Adv Setup

17 Adv Setup 10 - 01 Adv Setup Under Run Protect 10 . Advanced Setup Under Run Protect ON 10 - 02 Adv Setup Overburn 10 - 03 Adv Setup Read Error Skip 10 - 04 Adv Setup Burn - In 10 - 05 Adv Setup Update Firmware 10 - 06 Adv Setup Compare Firmware 10 - 07 Adv Setup H / W Diagnostics 10 - 08 Adv Setu...

Page 18 - Advanced Setup Menu

18 Update F/W T.950 To T.970 YES? Advanced Setup Menu To get to the Advanced Setup Menu, press and hold the ESC button for three seconds. The Advanced Setup menu includes options for the more advanced user. Normally these functions are not used in the daily operation of the QD-52 duplicator. If you ...

Page 20 - Appendix 1 List of Functions

20 Appendix 1 List of Functions 1 Copy 2 Test 3 Test & Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Edit Track (for CD only) 8-1 CD to CD Edit 8-3 Play Audio Track 8-4 Close Session 9 Setup 9-1 Language (Default is English) 9-2 CD Burn Speed (Default is Maximum) 9-3 CD Read Speed (Default is ...

Page 21 - Appendix 2 LCD Messages

Appendix 2 LCD Messages Normal Conditions: Initialize SDRAM ......................................................................Initialize the memory of the system. Detect Drives ....................................................Detect what drives are connected with the system. User Abort! ........

MicroBoards QD-2 - Manual

Table of Contents:

Summary

Other MicroBoards Models