MGE UPS Systems EXB RT 3U - Manuals

MGE UPS Systems EXB RT 3U – Manual in PDF format online.

Manuals:

Manual

Manual MGE UPS Systems EXB RT 3U

Summary

Page 3 - Introduction; Environmental protection; Substances

34007776EN/AB - Page 3 Introduction Environmental protection MGE UPS SYSTEMS has implemented an environmental-protection policy.Products are developed according to an eco-design approach. Substances This product does not contain CFCs, HCFCs or asbestos. Packing To improve waste treatment and facilit...

Page 4 - Pictograms

34007776EN/AB - Page 4 Introduction Pictograms Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio signal. In the illustrations on the following pages, the symbols below are used: LED off LED on LED flashing

Page 5 - Contents

34007776EN/AB - Page 5 Contents 1. Presentation 1.1 Standard positions ...................................................................................................................... 6 Tower position ................................................................................................

Page 6 - Standard positions; Tower position

34007776EN/AB - Page 6 1. Presentation 1.1 Standard positions Tower position Rack position Dimensions (H x W x D) in mm Pulsar M 2200 RT 2U 440 x 86 x 640 Pulsar M 2200 RT 3U 440 x 131 x 490 Pulsar M 3000 RT 2U 440 x 86 x 640 Pulsar M 3000 RT 3U 440 x 131 x 490 Pulsar M 3000 RT 3U XL 440 x 131 x 490...

Page 8 - Unpacking and contents check

34007776EN/AB - Page 8 2. Installation 2.1 Unpacking and contents check (30) Pulsar M 2200 or 3000 UPS (31) connection cable to AC-power source (32) 2 connection cables for the protected equipment (33) RS232 communications cable (34) USB communications cable (35) 2 systems to secure power plugs (36)...

Page 10 - Communication ports; Connection of RS232 or USB communication port (optional)

34007776EN/AB - Page 10 2. Installation 2.4 Communication ports Connection of RS232 or USB communication port (optional) Installation of the communication cards (optional) The RS232 and USB communication ports cannot operate simultaneously. 1 - Connect the RS232 (33) or USB (34) communication cable ...

Page 12 - HotSwap MBP-module operation; UPS start-up with the HotSwap MBP module; HotSwap MBP-module test; UPS connection without a FlexPDU or HotSwap MBP module

34007776EN/AB - Page 12 2. Installation HotSwap MBP-module operation UPS start-up with the HotSwap MBP module 1 - Check that the UPS is correctly connected to the HotSwap MBP module. 2 - Set switch (53) to the Normal position. 3 - Start the UPS by pressing the ON/OFF button (27) on the UPS control p...

Page 13 - UPS personalisation; Operation on battery power; Transfer to battery power

34007776EN/AB - Page 13 3. Operation 3.1 Start-up and normal operation UPS personalisation 3.2 Operation on battery power Transfer to battery power Low-battery warning For the initial start, AC power must be present to detect any wiring errors. Subsequently, the UPS can start even if AC power is not...

Page 14 - End of battery backup time; Return of AC power; Remote control connection and test

34007776EN/AB - Page 14 3. Operation End of battery backup time 3.3 Return of AC power Following an outage, the UPS restarts automatically when AC power returns (unless the restart function was disabled via UPS personalisation) and the load is again supplied. 3.4 UPS shutdown 3.5 Using the UPS remot...

Page 15 - ROO

34007776EN/AB - Page 15 3. Operation Contact open: shut down of UPSContact closed: start-up of UPS (UPS connected to the network and network energized) Note: local On/Off control via button (27) has priority over the remote control order. Contact open: shut down of UPS To return to normal operation,...

Page 16 - Access to measurements and personalisation data; Display menus arrangement; Local personalisation

34007776EN/AB - Page 16 4. Access to measurements and personalisation data 4.1 Display menus arrangement 4.2 Access to measurements Press the scroll button (25) to access any status conditions and alarms, then the measurements for voltage, current, frequency, power output and battery backup time. 4....

Page 17 - Output personalisation; Personalisation using external software

34007776EN/AB - Page 17 4. Access to measurements and personalisation data Output personalisation (1) These parameters may be modified only when the UPS is OFF. Detailed comments are available in the Personal Solution-Pac software. ON/OFF personalisation Battery personalisation 4.4 Personalisation u...

Page 20 - Mounting the new battery module; Maintenance on a UPS equipped with the HotSwap MBP module

34007776EN/AB - Page 20 5. Maintenance Mounting the new battery module Carry out the above instructions in reverse order. 5.3 Maintenance on a UPS equipped with the HotSwap MBP module D - Remove the metal protection cover in front of the battery (two screws). E - Pull the plastic tab to remove the b...

Page 22 - Technical specifications

34007776EN/AB - Page 22 6. Appendices 6.1 Technical specifications (1) Depending on the output voltage selected: 200V / 208V / 220V / 230V / 240V, the output power is 1980VA / 1980VA / 2200VA / 2200VA / 2200VA. (2) Depending on the output voltage selected: 200V / 208V / 220V / 230V / 240V, the outpu...