MGE UPS Systems 3 - Manuals

iii Contents Quick Start ..........................................................insert Important Safety Instructions ....................................i 1. Introduction ........................................................1—1 MGE UPS Systems .....................................................

iv 6. Advanced Configuration ..................................6—1 6A. Entering/Exiting Configuration Mode ....................................................6—16B Using Configuration Mode ....................................................................6—16C Configuration Options .................

1—1 Thank you for your purchase of the Esprit rack"UPS" from MGE. The Esprit "UPS" will providemany years of, trouble-free power protection forcritical high availability servers and other devices.Please read this manual fully, to familiarize yourselfwith the safety instructions and E...

2. Getting to Know Your Esprit Rack UPS 2A. Product Features & Benefits Features Benefits Comments ◗ Plug in operation Low installation cost ◗ Modular concept Greater flexibility Add batteries as needed ◗ High efficiency Longer life and back-up time Up to 93% on battery, 98% on utility ◗ 2/3 com...

2—2 2C. Esprit Rack UPS Product Views With Rack Kit Figure 2a. Rear View of Models 3 and 4 With Rack Kit and Extended Batteries Model 3 Model 4 Figure 2b. Optional Rack Mounting Kit Figure 2c. Typical Front Views of Models (ESP104) 3, 4, Extended Battery, Label Placement ! Models 3 and 4 Extended Ba...

3A. Storing the UPS and Recharging the Battery Always store the equipment in its original packaging. The battery is of the sealed lead-acid type. Battery recharge requires that the battery module beplugged into an energized NEMA 5-15 receptacle for 6-8 hours. The battery may be charged in thebox by ...

3E. Connecting the Optional Extended Battery Plug the DC battery cable into the UPS module as shown in Figure 2a . The cable plug is keyed, so make sure to align the plug properly to the receptacle. Do not force the cable on, nor attempt toreverse the connection. To do so, will damage the equipment ...

The transistor resistance is 27 ohms and the maximum current allowed is 140mA AC or DC with ambient temperature of up to 40°C. In order to get a "logic low" you have to limit the current to: logic low voltage required dividedby 27, logic low voltage = 0.5V. I max = 0.5/27=0.0185A=18mA. If yo...

3—4 Caution: Connect only computer-type loads to the Esprit UPS. Warranty is void if non- computer-type loads are connected to the UPS. 3J. Solution-Pac Software Solution Pac software allows you to interface your computer with the UPS. The software is loadedon your computer and through the communica...

4. Startup and Shutdown 4A. UPS Startup You are ready to start the equipment after installing the UPS module, optional battery module(s),any options, and the communication cable (if used). Follow these simple steps: 1. Connect your computer equipment. 2. Depress the green "ON" button. You wi...

4—2 If desired, the UPS can be set up to operate at a known, fixed frequency regardless of thedetected utility frequency. Fixed-frequency operation is often desirable in installations thatmake use of cold-start capability. Discussion on this is in the Advanced Configuration Section(section 6) of thi...

4—4 The "Fault Detected" LED turns on and acts as described above for ANY system alarm,including those that have their own status indicators (e.g. overload, replace battery). Button Operation There are 3 buttons present on the front panel: ◗ The grey, " " top button controls the audi...

Table 5a. Esprit Models 3 and 4 Rack UPS Specifications (Continued) Item Specification Comment Design standards Safety; UL, cUL 1778, Emissions;FCC A, Surge protection; ANSI C62.41, Transportation; (drop test), IEC 68 level 1, (vibration), IEC 68.2-6 level 3, testing; PowerCet tested Input connectio...

6. Advanced Configuration 890-=qwertyuio Esprit Front Panel Configuration Mode Usage and InstructionsFor advanced users only! The Esprit UPS is shipped from the factory with a configuration that is suitable for most applications.However, there are some circumstances where modification of the UPS ope...

6—2 It is possible to cycle backward through the configuration options by pressing and holding the topbutton. A given option setting can be forced to its factory default state by pressing and holding the bottom button. The middle (Power ON) button is not used in configuration mode. To leave configur...

6—3 Options 0, 1, 2 – Extended Battery Configuration These three option switches should be changed as shown in the table below when new batterycabinet(s) are added to the UPS. The standard setting for these options are all OFF, selectingthe single/internal battery module option. Option Setting Numbe...

6—4 Options 5, 6 – Input Voltage Tolerance Use these two option switches to select the Esprit’s sensitivity to low/high input voltage conditions.The Esprit will switch to battery power when the utility voltage falls outside the range selected.The percentages shown in the table below are subtracted/a...

6—5 Option 10 – Automatic UPS restart after Low Battery shutdown The factory setting for this option is ON, which allows the UPS to automatically turn its output back on following a Low Battery shutdown once input AC is present. This setting is theusual one for applications where the UPS is connecte...

7—2 7B. Recycling Your UPS In USA or Canada, call 1-714-557-1636, M - F, 6:00 A.M. to 5:00 P.M. PST. Ask for a returngoods authorization for free UPS or battery recycling. MGE does not cover return freightcharges for recycling and will not accept items without a return goods authorization number.

Other Fine MGE Products Eclipse Surge Suppressors Ellipse 300-1200 VA ESV+ UPS ESV+ Rack UPS 780-2200 VA 780-2200 VA EX UPS EX Rack UPS 700-3000 VA 700-3000 VA Call MGE for many more power solutions: (714) 557-1636 or (800) 523-0142  US MGE GREEN SWEEP Call MGE to return your UPS for freerecycling ...