McIntosh MT10 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY

2 The lightning ﬂash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “danger- ous voltage” within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons. 1. Read these instructions. 2. ...

Page 4 - Caution: To prevent possible damage to the turntable platter; Power Control Connector; necting Cable is available from the; Tonearm Headshell Wiring; Connector and Cable Information; Rear View of McIntosh MCC10 Cartridge

4 General Information and Cable Information General Information Caution: To prevent possible damage to the turntable platter bearing, do not move the MT10 Precision Turntable with the platter installed. 1. For additional connection information, refer to the owner’s manual(s) for any component(s) con...

Page 6 - The following dimensions can assist in determining the; Front View of the MT10

6 Dimensions Dimensions The following dimensions can assist in determining the best location for your MT10. 17- 1/2 " 44.45cm Front View of the MT10 Rear View of the MT10 Side View of the MT10 8- 3/16 " 20.80cm 8- 13/16 " 22.38cm 16- 5/8 " 42.23cm 13- 13/16 " 32.54cm 16- 1/4 "...

Page 7 - To prevent possible damage to the turntable

7 Unpacking the Turntable Unpacking the Turntable To protect the fine finish of the MT10 Precision Turntable during the assembly and adjustment process, it is advisable to prepare a suitable clean working area with a soft, clean fabric, such as a bed linen or blanket. It is recommended that the Prof...

Page 8 - Assembling the Turntable; To prevent possible damage to the Cartridge Sty-

8 4. Insert the two screws (from step 2) through the top of the headshell and into the Cartridge Body and fasten them with a small screwdriver. Make sure the sides of the Cartridge are parallel to sides of the Tone Arm Headshell before tighten- ing the screws. Refer to figure 9. 5. Remove any shippi...

Page 9 - Tone Arm Height Set Screw

9 Assembling the Turntable up with the Mc- Intosh MCC10 Car- tridge postion marking on the suface. Refer to figure 13. Then tighten the knurled knob to secure the position of the Coun- ter Weight. 9. Locate the Tone Arm Height Gauge (used for the McIntosh MCC10 Cartridge) from inside the accessory b...

Page 10 - Assembling the Turntable, con’t

10 Assembling the Turntable, con’t 19. Locate the Mc- Intosh Bubble Level and place it on the Turntable Plat- ter Mat. If the Bubble is not in the center circle of the Bubble Level adjust the height the Turntable Feet (by rotating them clockwise or counter clockwise) until it is level. Refer to figu...

Page 11 - Rear Panel Connections and Adjustments

11 Rear Panel Connections and Adjustments POWER CONTROL REMOTE IN receives turn-on signals from a McIntosh component and switches the Front Panel Illumination On/Off. POWER CONTROL RE- MOTE OUT sends turn- on signals on to another McIntosh Component Connect to the external Power Supply supplied with...

Page 13 - Front Panel Display, Switches, Lever and Record Clamp

13 Front Panel Display, Switches, Lever and Record Clamp Meter indicates actual rotation speed of the turntable platter POWER Switch turns AC Power On/Off, or Standby for Illumination only SPEED Switch selects one of three playback speeds, 331/3 rpm, 45 rpm or 78 rpm Record clamp helps to keep the p...

Page 14 - Power Selection; nection between the MT10 and the; Speed Selection; How to Operate the Turntable; Tone Arm Lift Lever

14 2. Release the Tone Arm from the Tone Arm Holder. Refer to figure 54. 3. Position the Tone Arm over the desired spot of the Pho- tograph record. 4. Pull on the top part of the Tone Arm Lift Lever towards the front of the turntable to begin playback. Power Selection Rotate the POWER Switch to sele...

Page 15 - Notes

Page 18 - Note: Tone Arm Height will vary depending on type of Car-; MCC10 Cartridge Specifications

18 General Speciﬁcations MT10 Turntable Speciﬁcations Overall Dimensions Width is 17-1/2 inches (44.45cm) Height is 8-13/16 inches (22.38cm) Depth is 21 inches (53.34cm) Note: Tone Arm Height will vary depending on type of Car- tridge installed. Playback Speeds 33-1/3 rpm, 45 rpm and 78rpm Motor Typ...