McIntosh MC2301 - Manuals

7 XLR Connectors Below is the Pin configuration for the XLR Balanced In- put, Input/Output Connectors on the MC2301. Refer to the diagram for connection: PIN 1: Shield/Ground PIN 2: + Output PIN 3: - Output Power Control Connector The MC2301 Power Control Input receives an On/Off sig- nal from +5 to...

8 Dimensions Dimensions The following dimensions can assist in determining the best location for your MC2301. There is additional infor- mation on page 9 pertaining to installing the MC2301 into cabinets. 17- 3/4 " 45.09cm 11" 27.94cm 12- 5/16 " 31.27cm 20" 50.86cm 21" 54.61cm 3/...

9 Installation Installation The MC2301 can be placed upright on a table or shelf, standing on its four feet. It also can be custom installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom of the MC2301 when it is custom installed as outlined below. Th...

11 Rear Panel Connections and Switch Connect the MC2301 power cord to a live AC outlet. Refer to the rear panel to determine the correct voltage POWER CONTROL IN receives a turn On/Off signal from a McIntosh component and the POWER CONTROL OUT sends a turn On/Off signal to the next McIn- tosh Compon...

12 Spade lug or prepared wire connection: Insert the spade lug connector or prepared section of the cable end into the terminal side access hole, and tighten the terminal cap until the cable is firmly clamped into the terminal so the wires cannot slip out. Refer to fig- ures 4, 5 & 6. Banana plu...

13 McIntosh Loudspeaker How to Connect McIntosh Preamplifier Connect to AC Outlet

14 3. If the cable is stranded, carefully twist the strands together as tightly as possible. Note: If desired, the twisted ends can be tinned with solder to keep the strands together, or attach spade lug and/or banana connector. Spade lug or prepared wire connection: Insert the spade lug connector o...

15 How to Connect for Bi-Amp McIntosh Loudspeaker McIntosh Preamplifier Connect to AC Outlet McIntosh Power Amplifier Two

16 Front Panel Displays and Controls Standby Power On and Sentry Monitor Tube Protection Activa- tion Indicator Meter indicates the Power Output of the Amplifier POWER Switch Turns AC Power On/Off, or On/Remote METER Switch selects the display modes of the Power Output Meter and Meter Illumination

17 amplifier. The meter pointer will then rise to the newer higher indication. If no further power peaks are reached, the meter pointer will very slowly return to its rest position or lower power level. The decay rate is approxi- mately 6dB per minute. Input Mode Switch The Input Mode Switch, which ...

18 Technical Description McIntosh Laboratory, the company who introduced the world’s first amplifier that could be called “High Fidelity”, has done it again. The McIntosh engineering staff has cre- ated a tube power amplifier without compromise, using the most advanced McIntosh circuit design concep...

20 feedback designs. The fully Balanced Push-Pull design is used from input to output. The resulting fully balanced configuration can- cels many forms of audible distortion and greatly improves the Signal-to-Noise ratio of the amplifier. While conventional designs only take output from the plate, th...

21 Technical Description, con’t should fail. During normal operation there is absolutely no compromise in sonic performance with this circuit, and it ensures safe operation of the amplifier under even the most extreme operating conditions. In the event a problem occurs, the MC2301 Sentry Monitor Tub...

22 Specifications Specifications Power Output Minimum sine wave continuous average power output is: 300 watts into 2 ohm load 300 watts into 4 ohm load 300 watts into 8 ohm load Output Load Impedance 2, 4 or 8 ohms Rated Power Band 20Hz to 20,000Hz Total Harmonic Distortion 0.5% maximum harmonic dis...