McCulloch 95390028700 - Manuals

Page 4 - A. GENERAL DESCRIPTION

ENGLISH – 1 A. GENERAL DESCRIPTION 1) Rear handle 2) Rear hand guard 3) Front handle 4) Front hand guard/chain brake lever 5) Chain tensioner knob/screw 6) Chain tensioner pin 7) Oil tank cap 8) Oil tank inspection gauge 9) Air vents 10) Cable 11) Manual 12) Switch 13) Switch block 14) Chain 15) Dri...

Page 5 - ENGLISH - 2; B. SAFETY PRECAUTIONS; Chain oil; Manual layout; : Section B is divided into various

ENGLISH - 2 B. SAFETY PRECAUTIONS MEANING OF SYMBOLS Warning! Read the instruction manual carefully Protective boots Protective goggles or visor, protective helmet and hearing protection Protective cut-proof gloves Protective long, cut-proof trousers Chain brake: deactivated, activated Disconnect th...

Page 6 - ENGLISH – 3; Precautions prior to machine use.

ENGLISH – 3 reference number of the corresponding component to draw the reader’s attention to the main safety procedure linked with that particular situation; the machine parts shown in “A – GENERAL DESCRIPTION” are indicated in italics in the text for easy identification. Precautions prior to machi...

Page 7 - ENGLISH - 4; Health precautions – Chemical agents.

ENGLISH - 4 6. Health precautions – Chemical agents. Avoid all chain oil contact with skin and eyes. 7. Health precautions - Electricity. All extension cords, plugs, and electricity lines must be homologated, to standard and in compliance with current regulations. Make sure that the main line to whi...

Page 8 - ENGLISH – 5; C. SAFETY EQUIPMENT DESCRIPTION

ENGLISH – 5 sure that the cable/ extension cord is kept behind the user, controlling that it does not create a source of danger for the user or for other persons, and check that it cannot be damaged (by heat, sharp objects, sharp edges, oil, etc); Always assume a stable standing position on both leg...

Page 9 - ENGLISH - 6; CHAIN CATCHER

ENGLISH - 6 The chain brake can be activated in two modes: the first using the left wrist by pushing forwards, or when it comes into contact with the brake system as a result of kickback; or by inertia, in the case of particularly violent kickback. When the machine is used with the bar in horizontal...

Page 10 - ENGLISH – 7; F. BAR AND CHAIN LUBRICATION

ENGLISH – 7 case do not tighten the chain immediately after use, but wait until it cools down. In cases where the loosened chain needs to be adjusted, always unscrew the bar retaining nuts / knob before adjusting the chain tensioning screw/knob ; adjust the tension and tighten the bar retaining nuts...

Page 11 - ENGLISH - 8; Every 2-3 hours of use

ENGLISH - 8 Check that the chain is sharpened correctly (See below), in good working condition and that the tension is correct. If the chain is irregularly worn, or if the cutting teeth are only 3 mm high, the chain must be replaced(fig.3). Clean the air vents regularly to prevent motor overheating....

Page 12 - ENGLISH – 9; Trunk on the ground.; (Risk of touching the ground; Trunk supported at one end only; (Risk of pinching the; FELLING CUTS

ENGLISH – 9 - At the end of each cutting operation the user will notice a considerable change in the strength necessary for controlling the machine. Great care must be taken not to loose control . Below is a description of two different types of cutting operation: Cutting action by pulling the chain...

Page 13 - ENGLISH - 10; Limbing

ENGLISH - 10 and lower cut. The meeting point between the two sides of the notch is called “directional cut line” This line must be perfectly horizontal at right angles (90°) to the felling direction. The felling cut that provokes the tree fall, is performed at 3 to 5 cm above the lower part of the ...

Page 14 - ENGLISH – 11; M. TROUBLESHOOTING TABLE; Make sure that

ENGLISH – 11 M. TROUBLESHOOTING TABLE Motor does not start Motor turns with difficulty or loses power The machine starts but does not cut properly Motor turns improperly or at reduced speeds Braking devices do not stop the chain properly Make sure the main line is powered z Make sure the machine is ...

Page 15 - ENGLISH - 12; N. DECLARATION OF CONFORMITY; Valmadrera, 19/05/2004; Chain; Guarateed sound power level Lw

ENGLISH - 12 N. DECLARATION OF CONFORMITY The undersigned, authorized by E.O.P.I., declares that the following products model: type ES15, ES 15/1, ES 15/2, ES16, ES 16/1, ES18 starting from 2004 onwards, manufactured by E.O.P.I., Valmadrera, Italy, comply with European Directive: 98/37/EEC (Machine ...