McCulloch 115306026 - Manuals

Page 2 - TABLE OF CONTENTS

2 TABLE OF CONTENTS Identification (What is What?) 2 Identification of Symbols 3 Safety Rules 3 Assembly 5 Operation 9 Maintenance 15 Service & Adjustments 16 Storage 18 Troubleshooting Table 19 Declaration of Conformity 20 Technical Data 21 IDENTIFICATION (WHAT IS WHAT?) 3 10 1 4 16 14 20 19 7 ...

Page 5 - ASSEMBLY; CARTON CONTENTS

5 S Keep others away when making carbure- tor adjustments. S Use only recommended McCulloch accesso- ries and replacement parts. S Have all maintenance and service not ex- plained in this manual performed by your au- thorized service dealer. FUEL SAFETY S Mix and pour fuel outdoors. S Keep away from...

Page 7 - ATTACHING THE SHIELD

7 3. Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes. Upper shoulder strap clamp Screws Lower shoulder strap clamp 4. Insert two screws into the screw holes. 5. Secure shoulder strap clamp by tighten- ing screws with a hex wrench. 76 cm HARNESS...

Page 9 - OPERATION

9 9. Remove the screwdriver. 10. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must re- install. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instru...

Page 13 - ADDITIONAL SAFETY RULES; FOR OPTIONAL ATTACHMENTS; EDGER SAFETY

13 ADDITIONAL SAFETY RULES FOR OPTIONAL ATTACHMENTS WARNING: For each optional attach- ment used, read entire instruction manual be- fore use and follow all warnings and in- structions in manual and on attachment. WARNING: Ensure handlebar is installed when using edger or brushcutter at- tachments. ...

Page 14 - HEDGE TRIMMER SAFETY; HANDS AWAY FROM BLADE; POLE PRUNER SAFETY

14 S Never operate the cultivator without the tine cover in place and properly secured. S Keep the tines and guard clear of debris. S After striking a foreign object, stop the engine, disconnect the spark plug and inspect the cultivator for damage. Repair before restarting. S Disconnect attachment f...

Page 15 - MAINTENANCE

15 SNOW THROWER SAFETY WARNING: Keep hands and feet away from the rotor when starting or running the engine. Never attempt to clear the rotor with the engine/motor running. Stop engine and disconnect spark plug before unclogging snow or debris from discharge chute or when adjusting vanes. WARNING: N...

Page 16 - REPLACE SPARK PLUG; SERVICE AND ADJUSTMENTS; REPLACING THE LINE

16 Air filter Air filter cover Knob REPLACE SPARK PLUG Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0,6 mm. Ignition timing is fixed and nonadjustable. 1. Twist, then pull off spark plug boot. 2. Remove spark plug from cylinder and dis- c...

Page 18 - STORAGE; SEASONAL STORAGE

18 Air filter cover Idle speed screw If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer. STORAGE WARNING: Perform the following steps after each use: S Allow engine to cool before storing or trans- porting. S Store unit and fuel in a...

Page 20 - DECLARATION OF CONFORMITY

20 DECLARATION OF CONFORMITY EC Declaration of Conformity (Only applies to Europe) We, Husqvarna AB , SE-561 82 Huskvarna, Sweden, tel: +46--36--146500, as authorised representative in the Community, declare that the brushcutter model McCulloch Cabrio 433L with serial numbers dating from 2009 and on...

Page 21 - TECHNICAL DATA

21 TECHNICAL DATA M ODEL: Cabrio 433L ENGINE Cylinder displacement, cm 3 33 At maximum engine power, rpm 7000 Maximum rotational frequency of the spindle 10000 Engine speed at recommended maximum spindle rotational frequency 7400 Recommended speed idling, rpm 2900 Maximum engine power, measured in a...