Master MK-470 - Manuals - manualsarea.com

Page 2 - Ta b l e o f C o n t e n t s; I M P O RTANT SAF ETY I NS TR U CTIO NS FOR T H E MK -47 0 T I L E S AW; Sa fe ty M es sa ges; Warning

Ta b l e o f C o n t e n t s Foryour safety, read all instructions! These safety precautions should be followed at all times. Failure to follow these safetyprecautions could result in injury to yourself and others. Safety is a combination of operatorcommon sense and alertness at all times when the s...

Page 3 - n o t i c e; Item; Ha zard S ym bol s; E l ec tr ic a l S h o c k !

Safety labels are located according to the drawing below. The labels contain important safety information. Please read themcarefully. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MKDiamond or your dealer for replacement. D amag e pr ...

Page 4 - Accessory Pack contains:; Do not operate saw until fully assembled.; In iti al A s s e m b l y; I ns tal li ng the B lade

3 Carefully open carton. Remove the accessory pack. Lift the saw out of the carton by the pan, and place onto a level work surface.Open the accessory pack, and check each item with the contents list and illustration below, making certain that all items areaccounted for and in good condition before d...

Page 5 - Ele ct rica l Requ irem ents an d Grou ndi n g In st ruc t io ns; Use of a temporary adapter is not permitted in Canada.; N o t e; Figure 1

The MK-470 tile saw is wired for 120V, single phase operation, and draws 5.3 amps at 120V. This is not a large load, howeverif the machine is operated on any circuit that is already close to its capacity, the circuit breaker may be tripped. If this occurs,eliminate other loads from the circuit. A se...

Page 6 - S a wi ng O per at io ns; Ge ne ra l Cu tt in g Gu ide lin es; Table 1; Lo ck Out M eth od; drip loop

S a wi ng O per at io ns Ge ne ra l Cu tt in g Gu ide lin es • A diamond blade does not cut, it grinds. Do not force the tile into the blade, nor feed it to quickly.• Diamond blades are not all alike. Match the MK blade to the product to be cut.• B e f o re mounting any blade on the saw, inspect the...

Page 7 - M a i n t e n a n c e; DO NOT Ser vice; square cut; Con veyo r Tabl e M ark in gs; m o t o r pr o bl e m s

Do not attempt to cut pieces too small to hold by hand outside the blade guard. Avoid awkward hand positions where a suddenslip could cause a hand or fingers to come in contact with the blade. When cutting any material, make sure it is fully supported.Hold workpiece firmly against the fence. Only fe...

Page 8 - Opt iona l Ac ce sso ri es; w a t er f lo w p r o b l em s

Opt iona l Ac ce sso ri es w a t er f lo w p r o b l em s Check that the water pump vibrates when the motor is on. Reprime pump: Take water hose off blade guard,remove air bubbles, fully submerse pump outlet in water, turn motor on.Plug the water pump into an electrical outlet, fully submerse pump i...

Page 12 - HOW TO ORDER PARTS; Please have the following information ready before calling:; PARA ORDENAR PARTES DE REPUESTO; Sírvase tener lista la siguiente información antes de llamar:; POUR COMMANDER LES PIECES DE RECHANGE; Veuillez avoir les informations suivantes avant d'appeler:

1315 Storm Parkway. Torrance, CA 90509-28031 (800) 421-5830 FAX 1 (310) 539-5158 (310) 539-5221 www.mkdiamond.com MK Diamond Products, Inc. R HOW TO ORDER PARTS Please have the following information ready before calling: SERIAL NUMBER OF YOUR SAWMODELNUMBER OF SAWWHERE PURCHASED AND WHENPART NUMBERP...