Master Bilt K - Manuals - manualsarea.com

Page 3 - TABLE OF CONTENTS; INSTALLATION INSTRUCTIONS............................................................................................... 6; General; CABINET COMPONENT AMP DRAW..........................................................................................11

3 TABLE OF CONTENTS INTRODUCTION………………………………….……………………………………………………………………4 STORE CONDITIONS…………………………….……………….…..…………………………………………….. 4 WARNING LABELS AND SAFETY INSTRUCTIONS………..…..……………………………………………… 5 PRE-INSTALLATION INSTRUCTIONS………………………..…..………………………………….…………… 6 Inspection for Shipping Damage…………...

Page 4 - INTRODUCTION; case. A parts list is included with this manual. Read all these; STORE CONDITIONS; store. The store temperature should be at or below 75; NOTICE

4 INTRODUCTION Thank you for purchasing a Master-Bilt cabinet. This manual contains important instructions for installing, using, and servicing a Master-Bilt BLG/TLG case. A parts list is included with this manual. Read all these documents carefully before installing or servicing your equipment. STO...

Page 5 - WARNING LABELS AND SAFETY INSTRUCTIONS; Severe injury or death will occur if you ignore the message.

5 CAUTION! GROUND REQUIRED FOR SAFE OPERATION WARNING LABELS AND SAFETY INSTRUCTIONS This symbol is the safety-alert symbol. W hen you see this symbol on your cabinet or in this manual, be alert to the potential for personal injury or damage to your equipment. Be sure you understand all safety messa...

Page 6 - PRE-INSTALLATION INSTRUCTIONS; INSPECTION FOR SHIPPING DAMAGE

6 PRE-INSTALLATION INSTRUCTIONS INSPECTION FOR SHIPPING DAMAGE You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage is noted to shipping crates or cartons or if a shortage is found, note this on ...

Page 7 - condensate pan from the top unit compartment.

7 ELECTRICAL WARNING Before servicing electrical components in the case or the doors or door frames make sure all power to case is off. Always use a qualified technician. Check voltage and amps drawn on (Page 17-20) to determine proper line and fuse or circuit breaker size. Check power supply for lo...

Page 8 - DOORS; cabinets have Anthony glass doors; Figure 3; Torque Adjustment

8 DOORS The BLG/TLG cabinets have Anthony glass doors that are equipped with a patented TorqueMaster ™ hinge system. The doors are easily adjusted using a flathead screwdriver (Fig.3). * The tension needs to be checked and set when first install. Figure 3 To remove the door shipping clamps, remove t...

Page 9 - ELECTRONIC REFRIGERATION CONTROL

9 MASTER-BILT ELECTRONIC REFRIGERATION CONTROL OPERATION Compressor When power is first turned on to the control, the LED indicator under COMP on the display starts blinking. After one-minute delay the compressor comes on. The COMP LED indicator stays on while compressor relay is energized. Display ...

Page 10 - HOW TO CHANGE THE SETPOINT; SET; or wait 15s without pressing a key.

10 HOW TO CHANGE THE SETPOINT 1. Push the SET key for more than 2 seconds to change the Set point value; 2. The value of the set point will be displayed and the LED under COMP starts blinking; 3. To change the Set value push the UP ▲ or DOWN ▼ arrows within 10s. To memorize the new set point value p...

Page 12 - FINAL CHECK LIST

12 FINAL CHECK LIST A. Check operating pressures. B. Check electrical requirements of unit to supply voltage. C. Set temperature control for desired temperature range. D. Check sight glass for proper refrigerant charge, if provided. E. Check system for proper defrost settings and operation. F. Check...

Page 13 - Disconnect power to the cabinet

13 Temperature sensor, defrost heater and fan motor replacement Before making any change, technician should: 1. Disconnect power to the cabinet 2. Remove screws from venturi and pull down To change a temperature sensor (cabinet zone sensor or defrost termination sensor), simply disconnect the sensor...

Page 14 - MASTER-BILT PART LIST; Sight Glass

14 MASTER-BILT PART LIST The table below gives Master-Bilt part numbers. Use this chart when ordering replacement parts for your BLG/TLG cabinets. Always Advise Cabinet Serial Number W hen Ordering Parts Description BLG/TLG- 27HD BLG/TLG- 48HD BLG/TLG- 52HD BLG/TLG- 74HD BLG/TLG- 80HD Ballast 23-017...

Page 15 - OWNER RESPONSIBILITY

15 Accessories (Includes HD Models) Description BLG/TLG- 27HD BLG/TLG- 48HD BLG/TLG- 52HD BLG/TLG- 74HD BLG/TLG- 80HD Baskets (Cantilever) 20” X 22” X 5” 33-01458 33-01458 Baskets (Conventional) 22”X 22-3/4”X 5” 33-01419 33-01419 Baskets (Conventional) 24-3/4”X22”X5” 33-01376 33-01376 Casters (4) 3”...