Page 2 - Required Tools; understand and identify all of the components.
PAGE 2 MantelMount MM750 Required Tools 7/32” 10-14mm 4-5mm Before you begin, please verify that all components are included and undamaged. If any parts are missing or damaged, contact MantelMount. Never proceed with missing or damaged parts! Lay out all components and make sure you identify that ea...
Page 3 - MAXIMUM; STUDS; larger than 50”; VESA; PAGE 3; This is not an installation step, only a verification.
MantelMount is designed for use only with decorative fireplaces that are not the primary heat source for a house. Temperature at the front edge of mantle should never exceed 110° F. A B C E D Mantle must not extend from mounting surface more than 19 inches (22 inches for non-recessed installations)....
Page 4 - Flat Back; Spacers; to Flange edge
Use a Vertical Brace {27} to determine if your television is a flat back or an irregular back. An irregular back will require spacers and longer screws to fill any spaces between the Vertical Brace and the TV. The Braces must be parallel to your television screen. Choose the correct screw diameter a...
Page 5 - Use this distance in Step 9; PAGE 5
The Vertical Braces {27} are always mounted higher than the bottom of the TV. However, the Brace Extenders {28} will be mounted one of two ways: Without a Sound Bar - The Brace Extenders are installed within a few inches above the bottom of the TV. With a Sound Bar - The Brace Extenders are installe...
Page 6 - PAGE 6; M A N T E L
Determine the Vertical Position of the Housing: This image at right shows that the further out a mantle extends, the more it will interfere with the arc of the lowering TV. The chart below gives clearance heights from the bottom of the TV to the top of various mantel sizes. However, the MM750 Lift H...
Page 7 - PAGE 7; Installation Options: Surface Mount
MantelMount MM750 PAGE 7 SURFACE MOUNT (non-recessed) installation using Horizontal Braces {31} to attach to existing wall studs, on top of existing drywall. The Horizontal Braces can reach studs that are up to 34 inches (875mm) apart. They attach flush to the back of the Lift Housing {30}. SURFACE ...
Page 8 - Cutting a Center Stud:; PAGE 8
{13} {11} FIG. C (view facing the wall) FIG. B (view from inside the wall) FIG. A (view from inside the wall) opening MM750 includes brackets that make it easier to install horizontal pieces of 2x4 bracing inside the wall. This is because all of the attachment holes in the Brackets can be reached fo...
Page 9 - THIS STEP REQUIRES TWO PEOPLE; Distance from; CL; Marking the Location for the Lift Housing {30}; PAGE 9
DO NOT damage or scratch the rods of the Gas Springs! THIS STEP REQUIRES TWO PEOPLE Pull the Safety Braces out to the ready position as shown. You might need to flex them over the screws. Do not bend the Safety Braces. Firmly and slowly pull down the Arm until the Lifting Mechanism is in a horizonta...
Page 10 - MantelMount MM750; ONLY WITH
PAGE 10 MantelMount MM750 ! WARNING: DO NOT put hands into Lifting Mechanism while operating the mount. Severe Injury can occur due to pinching or crushing. Always use the Safety Braces when working near or inside MantelMount. Install the TV Frame {26} using 4 Screws {20} and Washers {11}. These scr...
Page 11 - PAGE 11
Adjusting for Television weight: With Safety Braces in place, use a socket wrench with an extension to adjust the long bolts inside the Lift Housing {30}. Take turns adjusting each side so they stay relatively even with each other. Turn the bolts clockwise (AS SHOWN BELOW) to pull the Gas Springs do...
Page 12 - Adjusting the Hard Stops for Range of Motion:
Adjusting the Bottom Stop Position : Loosen the Locknuts and adjust the Bottom Stop screws to the desired stopping position. There are two screws underneath the Lifting Mechanism. Turn these screws inward until they tighten at the desired lower position. Tighten both locknuts after the adjustments a...
Page 15 - PAGE 15
MantelMount MM750 PAGE 15 ITEM NO . PAR T NUMBER DESCRIPTION Q TY. ITEM NO . PAR T NUMBER DESCRIPTION Q TY. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30 31 32 33 34 35 36 37 38 39 40 41 42 43 45 44 46 47 48 49 50 26 27 28 29 54 55 56 57 58 59 53 52 51 12189 4 12190 4 12191 4 ...
Page 16 - Full Manufacturer Warranty:; MantelMount will replace or repair any product or part; Exclusive MantelMount Features!
PAGE 16 U.S. Pat. No. 8,864,092 01Jan2018 MantleMount MM750 Customer Service: (800)-897-9755 www.MantelMount.com 20.5 Max Recessed Clearance 17.0 M in Recessed Clearance 30.5 Maximum Drop 31.5 1.8 Thick ness 35.427.8 725 mm Soundbar 13.3 Full Manufacturer Warranty: MantelMount will replace or repair...
