M-Audio 52803 - Manuals

Rear Panel 1. Power Switch: The Power Switch turns on the M-Audio Ozone. You probably figured that one out for yourself. 2. Power Jack: This jack is used to connect the keyboard to the supplied 9VAC 1000mA “wall-wart” type power supply. 3. USB Port: This USB connector jack is used to connect the M-A...

12. Mic In (Channel 1): This is an XLR Balanced preamp input for microphones. Mic In preamp gain is controlled by the top panel “MicGain” control. This input also gets defeated if the Aux Input is pluggedin, and the Monitor/Record button is pressed to the “Record” position. 13. Direct Monitor Stereo...

15. The “Found New Hardware Wizard” will again appear. Click “Next” to continue. 16. Another Windows Logo Testing window will appear. Click “Continue Anyway” to continue. 17. The next window informs you that the Wizard has finished installing the software. Press “Finish” to continue. Your installati...

8. An M-Audio Setup Window will come up, confirming a successful setup. Click, “Next,” to successfully install the M-Audio Ozone. 9. Windows will prompt you to restart the computer. Make sure that “Yes, restart my computer now,” is checked and then click, “Finish,” to restart 10. When you are comple...

installation (if you have not previously installed this update). Click“Next” to install DirectX 8.1. 4. Click next to verify that you would like to install Microsoft DirectX 8.1. 5. The next window shows the Microsoft DirectX 8.1 license agreement. Click “Yes” to continue. 6. Click “OK” at the next ...

7. After restart, the next window reminds you to verify that the M-Audio Ozone is disconnected from the USB bus before continuing, and that youhave closed all other Windows applications. Do so now, then click “Next”to continue. 8. An M-Audio Setup Window will appear next. Make sure both “Enable Digi...

10. The following window prompts you to restart your computer.With the checkmark enabled, click “Finish” to restart. 11. After Windows has completely restarted, turn on your device using the power button on the back of the M-Audio Ozone. A window will thenprompt you to click “Next” to continue. 12. ...

13. The next window defaults to browse to a specified location. Click “Next” to continue. 14. In the next window, click “Next” to install the recommended driver. 15. The next window prompts you that the driver will now be installed. Click “Next.” 23

16. The final window tells you that installation is complete. Click “Finish”.. After a few more ‘automatic’ windows which do not require any action, theinstallation procedure reaches completion, and your device is ready to use. M-Audio Ozone and the Windows Sound System After installation, the M-Aud...

OMS Installation To install OMS from the driver CD, locate the OMS 2.3.8 folder on this CD,find the OMS installer program in the folder, and double click on its icon tobegin installation. Once this process completed successfully, you can moveon to the M-Audio Ozone Installer. M-Audio Ozone Driver In...

1. Go to "System Preferences" in the Apple Menu.2. Select the "Sound" preference panel, and click the "Output" tab. 3. Select "M-Audio Ozone" to choose the M-Audio Ozone as your default output device. You can also select the “Input” tab to make theM-Audio Ozone the de...

Connection Status: The M-Audio Ozone Control Panel will only be accessible when your M-Audio Ozone is connected to the computer andrecognized by the system. When the M-Audio Ozone is not connected, thepanel will either be grayed out, or a message will pop up indicating that theM-Audio Ozone is not r...

sure that the M-Audio Ozone audio driver is set to “M-Audio Ozone ASIO.” Within your music application, when you assign an audio track to receiveits input from the M-Audio Ozone Channel 1 or Channel 2—whether it’sthe Mic In and Instrument In, or when using the Aux Inputs in “Record”mode—you will set...

Using the Mic and Instrument Inputs Channel 1 of the M-Audio Ozone gives you a high gain, low noisemicrophone preamp. It provides a low impedance microphone input on anXLR connector with optional phantom power. A dynamic, condenser, orany other type of low impedance microphone will interface easily ...

Setting Input Gain The M-Audio Ozone provides up to 60dB of gain on the Channel 1 Mic Inand 40dB of gain on the Channel 2 Instrument In. Microphones typicallyemit a low signal level, requiring a "pre-amp" such as the M-Audio Ozoneprovides. Other instruments, such as guitar pickups and even s...

to be safe, check your mic’s documentation to see if it will accept or needsphantom power. Some ribbon mics definitely should NOT receivephantom power, as this could damage them. Using the Aux Inputs The M-Audio Ozone has a pair of “Aux Input” line inputs, both on a single1/4” TRS jack. It is design...

Also, as we mentioned, using Record mode defeats the Mic and Instrumentinputs, so you will not be able to listen to or record from those inputswhen the Aux Input is in Record mode. Another example is to use the Record mode only to switch Channel 1 andChannel 2 to line inputs, for the purpose of reco...

monitoring, mute the channels you are recording to, or send their outputto another bus. In a typical Direct Monitor application, plug your microphone and guitarinto Channel 1 and Channel 2 on the rear panel. Arm a pair of inputs inyour computer recording software and set their recording levels using...

In the following setup, the M-Audio Ozone is being used as a MIDIcontroller as well as a MIDI interface, inputting MIDI data to the computerand its application software, and outputting MIDI to a sound module fromwhich sounds will be produced. The M-Audio Ozone as a controller mayalso send MIDI infor...

The keys on the M-Audio Ozone, in conjunction with the MIDI/SELECTbutton, give you the extra programming capability that is unique toM-Audio’s line of MIDI controllers (including the M-Audio Ozone, Oxygen8and Radium).You can use the Data Entry key to enter in values, or the keysthat are labeled with...

of your choice, send program change data from the keyboard, select theMIDI transmit channel of the M-Audio Ozone, set the octave or pitch ofthe keyboard, and program the eight rotary controllers. DATA ENTRY Assignments: Pressing the MIDI/SELECT button then pressing a key labeled by its MIDI function...

4. Assign the MIDI channel number on number key group (1-16) then press Enter. This channel assignment will apply only to the controllerknob that you are programming. 5. You can select up to five banks of presets for the M-Audio Ozone’s keyboard, P1-P5, by pressing the MIDI/SELECT button. This is mo...

Technical Support & Contact Information For additional technical assistance, contact M-Audio Technical Support bytelephone (626-445-8495, 9-5 PST M-F), by fax (626-445-7564) or bye-mail ([email protected]). If you have questions, comments or suggestions about this product, or anyM-Audio produ...

M-Audio Ozone Warranty Information M-AUDIO warrants that this product is free of defects in materials andworkmanship under normal conditions for 90 days, so long as the productis: owned by the original purchaser; the original purchaser has proof ofpurchase from an authorized M-AUDIO dealer; and the ...

M-Audio Ozone Technical Specifications General • Supports 24-bit or 16-bit audio input or output • Supports the following sampling frequencies (Hz): 8000, 11025, 12000,16000, 22050, 24000, 32000, 44100, 48000, 88200, 96000 • (Note: Because of USB bandwidth and device hardware constraints,there are l...