M-Audio 1010LT - Manuals

Macintosh • 128 MB of RAM for 96kHz operation. 64MB SDRAM for 48kHz or less. • Mac G3 with 128 MB of RAM recommended. Some faster Power PCs will perform adequately. • Mac OS 8.5.1 or higher.• UDMA EIDE or fast SCSI HDD recommended. Breakout Cable 1: 1. Word Clock Input: This female BNC connector is ...

Breakout Cable 2: 7. Host Cable connector: This 44-pin female D-sub connector is used to attach the breakout cable to the PCI host card’s male D-sub connector. 8. Analog Inputs 3-8: These jacks input analog audio from a variety of external sources. Each jack is RCA coaxial and is compatible with RCA...

Changing the jumper setting is easy to do when the 1010LT PCI card is notinstalled in the computer. Since it is usually impossible to change the jumperswhile the card is in the computer, it’s a good idea to make a decision now. If youwish to connect a dynamic or ribbon microphone directly to the Del...

3. Select the PCI slot where you will install your Delta 1010LT PCI host card. Make sure the slot is a PCI slot. If you don't know what "PCI slot" means,check the owner ’s manual for your computer. PCI slots are distinguishablefrom ISA slots by being shorter and set back farther from the out...

4. The ‘Wizard’ reports that its Windows driver file search has found the M-Audio Delta 1010LT. Click Next>. If announcements that “No DriverSignature” pop up, ignore them and continue with the installation procedure. 5. Windows is now ready to install the driver files from the specified location...

to the Delta drivers, which will be D:\Delta Products\Delta98 (these driversalso work in Win95). Click ‘Next>’. 4. Windows will start to copy files, with a progress indicator on the screen. Once this process completes itself, your Delta 1010LT will be ready for action. After completion of the dri...

Delta Driver Software Installation on the Mac 1. Open the System folder on your Macintosh hard drive. In the System folder, locate the Extensions folder. 2. On you Drivers CD disk, open the Mac Delta Drivers folder. Place the extension file "Delta 1010LT Driver" in your Extensions folder by ...

1. In the Opcode folder, which you will find on your hard drive, locate the OMS Applications folder, "then OMS Setup." Double click on OMS Setup. 2. OMS will inform you that it has not yet been configured. Click OK.3. The Create A New Studio Setup dialog box now appears. Click OK.4. The "...

Windows may also use the Delta 1010LT as its default MIDI device. This allows theDelta 1010LT to be used with the MIDI applications included with Windows. To set thisup, go to Control Panel | Multimedia | MIDI. Set the Delta MIDI driver as the defaultWindows MIDI driver by clicking on the "MIDI ...

mode, the left channel of the S/PDIF In is routed to OUT4 and the rightchannel of the S/PDIF In is routed to OUT3. 4. Options four through seven connect the hardware analog inputs 1 & 2, 3 & 4, 5 & 6, or 7 & 8 (respectively) directly to the 1010LT’s hardware analog outputs 3 & 4....

data. Different manufacturers’ products may interpret these codes differently and require youto set these bits by "trial-and-error" until proper operation is achieved. CONSUMER FORMAT ADVANCED SETTINGS (Emphasis): This status bit is used to indicateif pre-emphasis has been applied to the out...

Delta 1010LT Control Panel Software - Mac The Delta Control Panel must be placed on the hard drive by dragging the application fromthe Drivers CD. Once this is done, an alias may be created by highlighting the DeltaControl Panel on the hard drive and pressing the Apple key+M. Then, this alias may be...

Further to the right are more channels, labeled "H/W In S/PDIF" and "H/W In 1/2." Thesemixer inputs are audio streams from the physical Delta 1010LT hardware inputs, hencethe "H/W" at the front of each label. PAN: Each mixer input may be individually panned anywhere in the st...

hardware S/PDIF output on your Delta 1010LT PCI host card. 2. The second option, "Monitor Mixer," connects the S/PDIF Out port to the outputs of the Delta 1010LT monitor mixer. For more information on thecapabilities of the monitor mixer, please see the section "Monitor Mixer Page.” 3. T...

VARIABLE OUTPUT LEVELS: This section has two layers, providing extremely versatilecontrol of your Delta 1010LT’s input and output operating line levels. In the first layer there are three selections available for globally setting the operating linelevels for the Delta 1010LT’s analog input and outpu...

In the upper righthand corner of the control panel is a “H/W Installed” drop-down list. Atthe time of this writing, the Delta Mac ASIO drivers will support only a single Delta device,and of course the Sound Manager will support only one stereo pair regardless of how manyaudio cards are installed in ...

Transferring from DAT to Delta 1010LT 1. Connect the DAT’s coaxial S/PDIF output to the S/PDIF In of the Delta 1010LT PCI host card, using a good quality cable. 2. Connect the 1010LT analog outputs 1 & 2 to some type of amplified sound system. The sound system should be equipped with speakers or...

5. In order to monitor the digital signal coming into the 1010LT, switch to the Patchbay/Router page of the control panel software. In the "H/W Out 1/2"column, select the radio button named "S/PDIF In." This will copy all S/PDIFinput audio directly over to the analog outputs – theref...

Troubleshooting This section addresses potential problems that can occur in all operating systemenvironments, with emphasis on hardware troubleshooting. Within the PC environmentthere are a limited number of hardware resources (I/O addresses, IRQs, and DMAchannels) available for use. Since audio car...

To change your system to Standard PC mode: 1. Boot into Windows and open the Device Manager. Right-click the + sign next to“Computer.” 2. Double-click the entry that appears under Computer, which should indicate that thecomputer is in ACPI mode. Click the Driver tab, then click the “Update Driver” b...

Problem: Repetitious Sound. Possible Cause: An IRQ resource conflict. Often this will result in a small segment of sound (0.5 to 1 second) repeating itself over and over, sometimes completelylocking up the computer. See the general troubleshooting suggestions at the beginning ofthis section. Problem...

Use Midiman/M-Audio Resources In addition to your manuals, we also provide you with the following sources ofinformation: Read Me Files : In your CD ROM, locate the Midiman/M-Audio product you own and open that folder. Find the appropriate Platform (Windows 95, 98, ME, 2000, Mac OS 9,X, etc.) that th...

Appendix A - Technical Specs Analog Audio Peak Analog Input Signal: +14.2 dBu (+4dBu setting+2.1dBV (-10dBV setting) Peak Analog Output Signal: +14.0dBu (+4dBu setting),+2.0dBV (-10dBV setting) Dynamic Range: Outputs: 101.5 dB (a-weighted), Inputs: 99.6 dB (a-weighted) THD (at 0dBFS): Outputs: less ...

Limited Lifetime Warranty MIDIMAN warrants that this product is free of defects in materials and workmanshipunder normal use so long as the product is: owned by the original purchaser; the originalpurchaser has proof of purchase from an authorized MIDIMAN dealer; and the purchaserhas registered his/...