LSI Logic 22902 - Manuals - manualsarea.com

Page 2 - Figure 1; Installation; Section 2.1, “Setting up the Installation”

2 LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server Figure 1 LSI22902 Host Adapter Kit 2 Installation The installation process contains the following four major sections: • Section 2.1, “Setting up the Installation” • Section 2.2, “Installing the Host Adapter Board” • Section 2.3, “Instal...

Page 3 - Setting up the Installation; Figure 2

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 3 2.1 Setting up the Installation Important: Make sure the ISP1100 server is turned off and is notplugged into an electrical outlet. Take all precautions tominimize ESD. A ground strap is recommended. Step 1. Identify the parts listed belo...

Page 4 - Figure 3; Figure 4

4 LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server Step 4. Lift the cover using the notch in the front of the cover andremove. Refer to Figure 3 for a photograph of the ISP1100. Figure 3 Intel ISP1100 Internet Server Step 5. Locate the components of the ISP1100. Refer to Figure 4 for a p...

Page 5 - Installing the Host Adapter Board; Identify the PCI low profile slot for the host adapter board.

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 5 f. Slimline floppy and CD-ROM assembly. g. Two hard drive bays. The ISP1100 is provided with a floppy cable for hard drives,but no drives are installed or included. h. IDE cable with hard drive connectors. The cables are routed under the...

Page 6 - Figure 5; Figure 6

6 LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server Refer to Figure 5 . Step 2. On the back of the chassis, remove the two screws holding theexpansion bays retention bracket. Step 3. Remove the retention bracket and the expansion slot cover. Figure 5 PCI Slot Location You can use one of t...

Page 9 - Remove the floppy drive cable as shown in

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 9 Figure 7 Method 2 Installation At this point in the installation process, you should be at the same point,regardless of the installation method chosen. Proceed with the next step. Step 6. Remove the floppy drive cable as shown in Figure ...

Page 11 - Installing New Drives; Refer to

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 11 Figure 9 CD-ROM and Power Cables 2.3 Installing New Drives This section of the procedure describes installing the proper SCSI harddrives, as well as a CD-ROM drive and floppy drive, in the ISP1100. Italso includes removing the existing ...

Page 13 - Removing the Hard Drive Bays

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 13 Figure 11 Removing the Hard Drive Bays Note: Each device on the SCSI bus, in this case, the host adapterand hard drives, must have a unique SCSI ID. SCSI ID 7 isthe default host adapter setting. See the documentation foryour hard drives...

Page 14 - Removing the IDE Cable

14 LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server Figure 12 Removing the IDE Cable Step 5. Pull the Slimline floppy cable up and lay it out of the waytemporarily. Step 6. Attach the preformed 68-pin LVD SCSI cable to the hostadapter board. Step 7. Route the cable along the side of the ...

Page 15 - SCSI Cable Routing; Step 10. Firmly press down on the rear of the bay until the bay “snaps”

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 15 Figure 13 SCSI Cable Routing Step 9. Install both drive bays by positioning the front tabs in theirrespective positions with the rear of the bay over the chassissnaptop standoffs. Step 10. Firmly press down on the rear of the bay until ...

Page 16 - Drive Bay Installation

16 LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server Figure 14 Drive Bay Installation Step 12. Reinstall the CD-ROM and floppy drives. Use the three mounting screws and attach the CD-ROM/floppydevices to the chassis, taking care to not overtighten themounting screws. Overtigntening cause ...

Page 17 - CD-ROM and Floppy Installation; Completing the Installation

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 17 Figure 15 CD-ROM and Floppy Installation 2.4 Completing the Installation Step 1. Attach the loose end of the hard drive LED cable to the serverboard SCSI LED connector, J11. Refer to Figure 16 on the next page for a photograph showing t...

Page 18 - Attaching the Hard Drive LED Activity Cable

18 LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server Figure 16 Attaching the Hard Drive LED Activity Cable

Page 19 - Notes

LSI22902/22903 Host Adapter to Intel ISP1100 Internet Server 19 Notes