Lincoln 2010 Town Car - Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of their vehicle. Only use cel...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Brake system warning light: To confirm the brake system warninglight is functional, it willmom...

Loading chapter. When the ignition is first turned to on, the light will illuminate for three seconds to ensure the bulb is working. If the lightdoes not turn on, have the system inspected by your authorized dealer.For more information on this system, refer to Tire pressure monitoring system (TPMS) ...

GAUGES Speedometer: Indicates the current vehicle speed. Refer to the Message center in this chapter to change your display to a digitalspeedometer. The digital display ismore accurate than the analoggauge and may not match. Engine coolant temperaturegauge: Indicates engine coolant temperature. At n...

Fuel gauge: Indicates approximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly when thevehicle is in motion or on a grade. The arrow near the fuel pump iconindicates which side of the vehiclethe fuel filler door is located. Refer t...

10. The compass is now calibrated. OIL LIFE START VALUE PRESS SELECT TO CHANGE Press SELECT to change the oil life start value. OIL LIFE START VALUESET TO XXX% will be displayed. To reset the oil monitoring system to 100% after each oil change(approximately 7,500 miles [12,000 km] or six months), pe...

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use (Note: this includesthe use of the optional full-sized matching spare tire and wheel). Formore information on how the system operates under these conditions,refer to Tire Pressure Monit...

AUDIO SYSTEMS Premium AM/FM Stereo Single CD/Cassette system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary respo...

The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission (CRTC) recommend that FM radiobroadcasters use RBDS technology to transmit information. FM radiostations are independently operated and individually elect to use RBDStechnology to transmit station ID ...

12. REW (Rewind): Press to rewind in tape or CD mode. FF (Fast forward): Press to fast forward in tape or CD mode. 13. SCAN: Press SCAN to hear a brief sampling of radio stations,selections or CD tracks. Press againto stop. 14. SHUF (Shuffle): Press to play the tracks on the current CD inrandom orde...

Premium plus AM/FM Stereo In-dash Six CD sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibili...

2. SEEK: Press to access the next/previous radio station or CDtrack. Press and hold toadvance/reverse in the current CD track. 3. TUNE/CAT: Press to manually go up or down the radio frequency. CAT is only available when equippedwith Satellite radio. Your vehicle may be equipped with Satellite readyc...

Press SEL-TEXT again to disable the feature when COMPRESS ON is displayed. When activated, the compression icon will illuminate inthe display. Occupancy mode: (Available on Premium plus audios): Press MENU until occupancy mode appears in the display. Press SEL-TEXT to select ALL, DRIVER or REAR SEAT...

12. LOAD: Press to load a CD. When the system prompts you,select a preset to load a CD in thatparticular slot. Load the CD. If you do not pick a slot, the system willselect the next available slot. Available slots are indicated by smallflashing indicators in the display. Press and hold to autoload u...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio andTelecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factor...

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circul...

DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL(DEATC) SYSTEM 1. A/C control: Cools the vehicle and is used to reduce humidity inthe vehicle. Press to turn on/off.The A/C control engages automatically in AUTO, and modes. 2. Recirculation control: Cools the vehicle more quickly byrecirculating the cabi...

15. EXT: Displays the outside air temperature. It will remaindisplayed until the EXT control ispressed again. The externaltemperature will be most accurate when the vehicle has been moving fora period of time. 16. Temperature conversion: Press to switch between Fahrenheitand Celsius temperature on t...

REAR CONSOLE CLIMATE CONTROLS (IF EQUIPPED) • TEMP: Press to increase or decrease airflow temperature. • FAN: Press to increase or decrease the fan speed. REAR WINDOW DEFROSTER The rear defroster control is locatedon the instrument panel. Press the rear defroster control toclear the rear window of t...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control....

6. Wait the desired amount of time for delay, then turn the headlampswitch to off. • At this point, the exterior lamps turn off and the time delay is set. High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlightand parking lamp operation. • Rotate the thumbwheel from leftto right to brighten theinstrument panel. • Rotate the thumbwheel from rightto left to dim the instrumentpanel. During full daylight, the instrument p...

• (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp bulb center from theground and mark an 8 foot(2.4 meter) horizontal reference lineon the vertical wall or screen at thisheight (a piece of ma...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Map/courtesy lamps To turn on the map lamps, press themap lamp control. Rear courtesy/reading lamps The courtesy lamp lights when: • the rocker control is pressed. • any door i...

Function Trade Number Rear grab handle reading lamps 578 Door courtesy lamp 904 Glove compartment 194 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer. * For vehicles with HID lamps, see your authorized dealer for servic...

Replacing headlamp bulbs To remove the headlamp bulb:1. Make sure the headlamp switch is in the off position, then open thehood.2. Remove the three retainers on top of the radiator cover and the tworetainers in front of the radiator cover.3. Remove the three bolts for each headlamp.4. Press the reta...

1. Make sure the headlamp switch isin the off position, then open thetrunk and remove the retainer. 2. Carefully pull the carpet away toexpose the lamp assembly hardware. 3. Remove the three nut and washerassemblies, then pull the lampassembly away from the vehicle. 4. Remove the bulb socket byrotat...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. WARNING: Never adjust ...

CLOCK Press the right control to move thetime display forward. Press the left control to move thetime display backward. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse...

REAR CENTER CONSOLE FEATURES (IF EQUIPPED) The rear center console incorporates the following features: • Utility compartment • Auxiliary power point (if equipped) • Remote radio/climate controls (if equipped) • Remote seat adjustment (if equipped) Remote seat adjustment The rear passenger can move ...

Accessory delay With accessory delay, the power window switches and radio may be usedfor up to 10 minutes after the ignition switch is turned off or until anydoor is opened. INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or do...

To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Memory feature (if equipped) ...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press a...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The light will be ...

• Press the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Press the brake pedal. This willnot erase your vehicle’spreviously set speed. • Press the speed control OFFcontrol. Note: When you ...

Car2U 威 Home Automation System HomeLink 姞 Wireless Control System (if equipped) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a convenient way toreplace up to three hand-heldtransmitters with a single built-indevice. This feature will learn theradio frequency codes o...

press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat thissequence a third time to complete the programming. HomeLink 威 should now activate your rolling code equipped device. To program additional HomeLink 威 buttons be...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

If the battery is disconnected, discharged, or a new battery is installed,the power trunk needs to be reset. To reset the power trunk: • Reconnect the battery with the trunk closed • Power activate the trunk with the power interior trunk release, thekey fob or the keypad on the door to the full open...

KEYS Your vehicle is equipped with a master key and a valet (identified withthe word VALET) key lock system. • The master key will access the vehicle’s doors, trunk, glove box,ignition and remote trunk release. • The valet key will access doors and ignition only. Before using the valet key with an a...

Autolock This feature automatically locks all vehicle doors when the followingconditions are met: • all the doors are closed, • the engine is running, • you shift into gear, putting the vehicle in motion, and. • the vehicle’s speed is greater than 3 mph (5 km/h). Autorelock The autolock feature repe...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

The remote entry system allows youto lock or unlock all vehicle doorswithout a key. Note: The remote entry features operate with theignition in any position except in theon position, when the transmissionis in any gear other than P (Park)or N (Neutral). If there are problems with theremote entry sys...

Memory seat/mirrors/adjustable pedals feature (if equipped) The remote keyless entry system can also control the memoryseats/mirrors/adjustable pedals feature. With this feature, the first twoprogrammed transmitters will recall a different memory position. Press once to unlock the driver’s door and ...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

Tips for setting codes: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. Erasing personal codes 1. Enter the factory set 5–digit code. The keyless entry keypad andinterior lights will illuminate and the driver’s door will unlock. 2. Press and rele...

Immobilizer System PATS XCVR certification numbers Kuwait M.C/U.S.0 /5/7-12579 Mauritius TA/2005/15 Mayotte (F) Mexico RLVVIVP03-324 Morocco MR 1299 ANRT 2004 Netherlands Antilles (NL) Nicaragua NCG-CE-04-004 Northern Mariana Islands See USA Oman OMA/1265(A) 1308/2001 Puerto Rico See USA Qatar QTEL/...

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the samekey chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded key while starting the engine. Theseobjects will not cause dama...

Automatic disarming Switching the ignition to the on position with a coded key (programmed to your vehicle) disarms the vehicle and allows the engine to start. The indicator on the instrument panel will illuminate forthree seconds and then go out. If the indicator stays on for an extendedperiod of t...

1. Insert a previously programmedcoded key into the ignition. 2. Turn the ignition from the 1 (off)position to the 3 (on) position. Keepthe ignition in the 3 (on) positionfor at least one second, but no morethan 10 seconds. 3. Turn the ignition to the 1 (off)position, and remove the coded keyfrom th...

SEATING Adjustable head restraints WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in itsproper position. The driver should never adjust the head restraintwhile t...

Using the manual recline function (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and t...

Front seat armrest The front seat armrest has a lockingpin which prevents the armrest fromfolding down during a collision. Ifthe locking pin has engaged becauseof a substantial jolt, but no collisionhas occurred, you can disengage thelocking pin by first moving thearmrest forward until it stops toal...

The rear seat heat controls are located on the rear door panels andoperate like the front heated seats. Refer to the Heated Seats section in this chapter. Easy-access/easy-out feature (if equipped) This feature automatically moves the driver’s seat rearward 2 in (5 cm)when: • the transmission is in ...

The memory seat positions are also recalled when you press your remoteentry transmitter (unlock) control. To program the memory seat to remote entry transmitter, refer to Remote entry system in the Locks and Security chapter. SAFETY RESTRAINTS Personal Safety System 姞 The Personal Safety System 威 pr...

WARNING: Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, movethe seat all the way back. WARNING: When possible, all children 12 years old and under should be proper...

manner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occupant’s chest bylimiting the load on the occupant. Refer to Energy management feature section in this chapter. Determining if the Personal Safety System 姞 is operational The Personal ...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, press the releasebutton and remove the tong...

The lap belt does not adjustautomatically. Insert the tongue intothe correct buckle (the buckleclosest to the direction the tongue iscoming from). To lengthen the belt,turn the tongue at a right angle tothe belt and pull across your lapuntil it reaches the buckle. Totighten the belt, pull the loose ...

When to use the automatic locking mode This mode should be used any time a child safety seat (except a booster) is installed in the vehicle. Children 12 years old and undershould be properly restrained in the rear seat whenever possible. Referto Safety restraints for children or Safety seats for chi...

How to disengage the automatic locking mode WARNING: Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify thatthe ⬙ automatic locking retractor ⬙ feature for child seats is still worki...

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. WARNING: Do not use extensions to change the fit...

WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s airbagsystem. One-time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safet...

1. Turn the ignition switch to the on position. DO NOT START THEENGINE. 2. Wait until the safety belt warning light turns off (Approximately oneminute). • Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, buckle then ...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. WARNING: All occupants of the vehicle, including the driver, s...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbags did notinflate in a collision does n...

The SRS consists of the following items: • Driver and passenger airbag modules (which include the inflators andairbags) • safety belt pretensioners • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this cha...

detect the presence of a properly seated occupant and determine if thefront passenger’s frontal airbag should be enabled (may inflate) ordisabled (will not inflate).The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if: • the front passenger seat i...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: An out of position front center occupant could affect the decision of the front passenger sensing system. If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the Cust...

WARNING: Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback. WARNING...

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe collision will be inflated. The airbag was designed to inflate betweenthe door panel and occupant to further enhance the protection providedoccupa...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot function properly in the ev...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddler seat). Small...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether anchor, if applicable. Tug thechild seat from side to side and forward and back where it is secured tothe vehicle. The seat should move less than one inch when you do thisfor a proper installat...

Perform the following steps to install a child safety seat to the tetheranchor: 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, otherwise routethe...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back be...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more ev...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Warning Lamp will turn ON if the tire pressure is significantly low.Once the light is illuminated, ...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low TirePressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is in use.(This includes the optional full-sizedmatching wheel and tire). Repair thedamaged road wheel and re-mount iton the vehicle to restore systemfunctionality. F...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. Tires, Wheels and Loading 170 2010 Town Car (tow) Owners Guide, 1st PrintingUSA (fus)

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, thenthe load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now yo...

Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cross thechains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agen...

• To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. For additional information, refer to Automatic transmission operation in the Driving chapter. • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. S...

Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after thetrailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise abo...

STARTING Positions of the ignition 1. Off— shuts off the engine and allaccessories/locks the gearshift leverand allows key removal. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. On— all electrical circuitsoperational. Warning lightsillu...

You may experience a decrease in peak performance when the engine iscold when operating on E 85 ethanol. Do not crank the engine for more than 10 seconds at a time as starterdamage may occur. If the engine fails to start, turn the key to off andwait 30 seconds before trying again. Do not use startin...

• Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been operating for approxim...

Using ABS When hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainsteering control during ha...

WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. The parking brake is not recommended to stop a moving vehicle.However, if the normal brakes fail, the parking brak...

During traction control operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment and theengine will not “rev-up” when you press farther on the accelerator. Thisis normal system behavior and should be no reason for conce...

This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch islocated on the left side of the trunk.If this switch is in the off ...

2. Locate the access plug on theunderside of the steering columncover. 3. Remove the access plug using aflat head screwdriver, then pressand hold the override button using aflat head screwdriver. With the keyin the on position, apply the brakepedal and shift the transmission intoN (Neutral) while co...

• To return to O/D (overdrive mode), press the transmission controlswitch. The O/D OFF lamp will not be illuminated. • O/D (Overdrive) is automatically returned each time the key is turnedoff. 2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slipp...

The system detects obstacles within approximately 16 feet (five meters),at speeds above 2.5 mph (4 km/h) behind the rear bumper with adecreased coverage area at the outer corners of the bumper. If vehiclespeed is below 2.5 mph (4 km/h), the system detects obstacles withinapproximately 9 feet (2.6 me...

Audible Warnings Distance to Object Warning 13 feet (4 meters) to 19.6 feet(6 meters) Slow beep Speed below 2.5 mph (4 km/h) up to 1.4 feet (.4 meters) Solid 1.4 feet (.4 meters) to 3 feet(.9 meters) Fast beep 3 feet (.9 meters) to 4.5 feet(1.4 meters) Medium beep 4.5 feet (1.4 meters) to 6.3 feet(1...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved in a substantial jolt.After a collision, if the engine cranks but does not start, the fuel pumpshut-off switch may have been activated. The fuel p...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 10A Starter relay coil 2 10A Restraint control module (RCM),Occupant classification sensor(OCS), Passenger airbagdeactivation indicator (PADI) 3 10A Audio 4 10A Back-up lamps, Anti-lock brakesystem (ABS) 5 7.5A ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 8 10A Power decklid module (PDM),Overdrive cancel switch, Cluster,Compass module, LCM, TractionControl™ switch 9 7.5A Door lock switch illumination,Heated seat switch illumination,Electrochromatic mirror 10 15A Hazards 11 15A Turn signal 12 15A ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 26 15A LCM (Park lamps, corneringlamps, license lamps) 27 — Not used 28 7.5A Brake signal, LCM (BTSI), ABS 29 — Not used 30 — Not used 31 5A LCM (Key in) 32 7.5A Delay accessory (audio) 33 — Not used K101 — Delayed accessory Power distribution b...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 201 Micro relay A/C clutch 202 — Not used 203 Micro relay Ignition coil 204 Micro relay PCM 205 — Not used 206 Micro relay Fuel 207 — Not used 208 — Not used 209 Micro relay Horn 301 Mini relay Starter 302 Mini relay RASM (Air compressor) 303 Mi...

tire with a road tire as soon as possible. During repairing or replacing ofthe flat tire, have the authorized dealer inspect the TPMS sensor fordamage. WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System and should not be used. WARNING: Refer to Tire pressure monitoring...

• Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance •...

Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving withthe full size matching spare tire/wheel, do not exceed 70 mph(113 km/h). It is intended for temporary use only. This means if youneed to use it, you should replace it as soon as pos...

Before placing the jack under the vehicle, NOTE the jack location markings: JACK LOCATION-FRONT The jack location markings can befound on the lower outer edge of the body. • Locate the jack locator mark(B - semi-circle ) on the body (C) near the tire you are changing,then place the jack (D) under th...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m 1 ⁄ 2 x 20 100 135 * Torque specifications are for nut and b...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING:...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated in the grille. 3. Lift the hood until the liftcylinders hold it open. Maintenance and Specifications 237 2010 Town Ca...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Windshield washer fluid reservoir 2. Engine oil filler cap 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Engine oil dipstick (access behind air tube) 7. Power steering fluid reservoir 8. Engine coolant ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. Turn the bladeas much as possible to gain accessto the lock tab (A). Using a skinnytool, press the lock tab (A) torelease the blade from the arm loopand pull the blade from the arm. 2. Attach the new blade to the armloop a...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the...

overfilled, some oil must be removed from the engine by an authorizeddealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal o...

WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for yourvehicle’s engine. Refer to Maintenance product specifications and capacities later in this chapter for more information. Do not use supplemental engine oil additives, cleaners or oth...

Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner may adversely affectbattery performance and durability. WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted subst...

6. Release the parking brake. With your foot on the brake pedal and withthe A/C on, put the vehicle in D (Drive) and allow the engine to idle forat least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the id...

• Protection against rust and other forms of corrosion. • Proper function of calibrated gauges. When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(...

WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hotengine parts. WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels such as gasoline and ethanol are highlytoxic an...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

light or CHECK FUEL CAP message may not reset immediately; it may take several driving cycles for the check fuel cap light or CHECK FUEL CAP message to turn off. A driving cycle consists of an enginestart-up (after four or more hours with the engine off) followed by cityand highway driving. Continui...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the right fuel section. Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with a pump(R+M)/2 octane rating of 87. Some station...

rating. These products have not been approved for your engine andcould cause damage to the fuel system. Repairs to correct the effects ofusing an aftermarket product in your fuel may not be covered by yourwarranty. Many of the world’s automakers approved the World-Wide Fuel Charterthat recommends ga...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

indicate that the vehicle is not ready for I/M testing. To determine if thevehicle is ready for I/M testing, turn the ignition key to the on positionfor 15 seconds without cranking the engine. If the service enginesoon indicator blinks eight times, it means that the vehicle is not ready for I/M test...

4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the range between the MIN and MAX lines. Besure to put the cap back ...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/or...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for yourvehicle through your local Lincoln or Ford of Canada dealer. Thesequality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to comp...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................58 Air cleaner filter ...............267–268 Air suspension ...........................188 description ..............................188 Airbag supplemental restraintsystem ........................116–117, 126 and child safety seats ............119descript...

filter, specifications ........242, 268recommendations ...................242refill capacities ........................269specifications ..........................269 Event data recording ....................7 Exhaust fumes ..........................182 F Fail safe cooling ........................24...

Power trunk ..........................74, 76 Power Windows ...........................57 R Radio ......................................26, 31 Rear window defroster ...............41 Recommendations forattaching safety restraints forchildren ......................................131 Relays .............