Lincoln 2010 MKX - Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of their vehicle. Only use cel...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Powertrain malfunction/reducedpower: Illuminates when a powertrain or a AWD fault has beendete...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected. Contact yourauthorized dealer as soon aspossible. Normal braking is still functional unless the brake warning lightalso is illuminated. Airbag readiness: If this light fails to illuminate...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be checked. Referto Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will illuminate for...

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engine and let the eng...

Trip odometer: Registers the miles (kilometers) of individual journeys.See TRIP A/B under Message center in this chapter. MESSAGE CENTER Your vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicle problems and variousconditions with an informati...

MPG (L/100km) Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km. If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed for the ...

System check and vehicle feature customization Press SETUP repeatedly to cyclethe message center through thefollowing features: PRESS RESET FOR SYS CHECK For each of the monitored systems, the message center will indicateeither an OK message or a warning message for two to four seconds. Press RESET ...

Press RESET to turn autounlock on or off. POWER LIFTGATE (if equipped) This feature allows users to open/close the rear liftgate at the touch of abutton. Press RESET to turn the power liftgate on or off. EASY ENTRY This feature automatically moves the driver’s seat backwards for easyexit/entry from ...

CHECK COMPASS MOD — Displayed when the compass is not operating properly. If the warning stays on or continues to come on,contact your authorized dealer as soon as possible. INTKEY COULD NOT PROGRAM — Displayed when an attempt is made to program a fifth Integrated Key to the Remote Key EntrySystem. ...

AUDIO SYSTEMS AM/FM In-dash six CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s p...

• DELETE ALL SONGS: Press OK to delete all song’s from the system’s memory. The display will read ARE YOU SURE ? Press OK toconfirm deletion of all saved songs and the display will read ALLDELETED. Note: If there are no songs presently saved, the display will read NO SONGS. • ENABLE ALERTS / DISABLE...

Bass: Press / to adjust the bass setting. Treble: Press / to adjust the treble setting. Balance: Press / to adjust the audio between the right and left speakers. Fade: Press / to adjust the audio between the front and rear speakers. Speed sensitive volume: Radio volume automatically changes slightly...

Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connectors at each end To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. En...

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the portable music player should be stored in a securelocation, such as the center console or the glove box, when the vehicle isin motion. The audio exte...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Radio Display Condition Action Required NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. You are in a location that is blocking the SIRIUS signal (i.e., tunnel, under an overpass, dense foliage, etc). The system is working properly. When you move into an ope...

DUAL AUTOMATIC TEMPERATURE CLIMATE CONTROL WITHHEATED AND COOLED SEATS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. MAX A/C setting: In order to achieve maximum cooling performance, press , A/C, , and set the temperature...

13. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engagesautomatically in AUTO, (defrost) and (floor/defrost). 14. OFF: Outside air is shut out and the fan will not operate. 15. Driver side temperature control: Press to i...

• Manual operation: 1. Select or . 2. Select A/C and (recirculated air). Use (recirculated air) with A/C to provide colder airflow. 3. Set the temperature to 60°F (16°C). 4. Set highest fan setting initially, then adjust to maintain comfort. To aid in side window defogging/demisting in cold weather:...

CABIN AIR FILTER The cabin air filter element is designed to reduce the concentration ofairborne particles such as dust, spores and pollen in the air beingsupplied to the interior of the vehicle. The presence of a particulate filterelement provides the following benefits: • Improves your driving com...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Adaptive headlamps (if equipped) The headlamp beams move in the same direction as the steering wheelwhich ...

Fog lamp control The headlamp control also operatesthe fog lamps. The fog lamps can beturned on when the headlamp control is in the , , or positions and the high beams arenot turned on. Pull the headlamp control towardsyou to turn the fog lamps on. Thefog lamp indicator light will illuminate. High b...

WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may notprovide adequate lighting during these conditions. Failure to activateyour headlamps under these conditions may result i...

• (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp bulb center from theground and mark an 8 foot(2.4 meter) horizontal reference lineon the vertical wall or screen at thisheight (a piece of ma...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument pan...

Map/dome lamp (if equipped) The dome lamp lights when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition is off. The map lamps are activated by pressing the controls on either si...

Replacing interior bulbs Check the operation of all bulbs frequently. Replacing headlamp bulbs Check the operation of all bulbs frequently. 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Reach over the front bolster. Highbeam bulb Lowbeam bulb 4. Remove the bulb ...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Normal speed operation of rearwiper. 1 — Intermittent operation of rearwiper. O (off) — Rear wiper and washer off. For rear wash cycle, rotate (and hold as de...

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamp. Slide on rod feature The visor will slide back and forthon the rod for increased sunlightcoverage. Rotate the visor towardsthe side window and extend itrearward for additional sunlightcoverage. Note: To stow the visor ba...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: 1. Cupholders 2. Tissue box holder (if equipped)(located on underside of consolelid) 3. Rear power point 4. Utility compartment with aSecondary storage bin with coinholder slots (on hinges inside utilitycom...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

One-touch up (front windows only) Allows the driver and passenger’swindow to close fully withoutholding the control up. Pull theswitch completely up to the seconddetent and release quickly. Thewindow will close fully. Momentarilypress the switch to any position tostop the window operation. Global op...

Window lock The window lock feature allows onlythe driver and front passenger tooperate the power windows. To lock out all the window controls(except for the driver and frontpassenger) press the right side ofthe control. Press the left side torestore the window controls. Accessory delay With accesso...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

SPEED CONTROL With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. Th...

Navigation system/SYNC 威 hands free control features (ifequipped) Press control briefly until the voice icon appears on the Navigation display to use the voicecommand feature. Press to activate phone mode or answer a phone call. Press VOL + or− to adjust volume. Press andhold to exit phone mode or e...

The panoramic Vista Roof™ and power sunshade are equipped with anautomatic, one-touch, express opening feature. To stop motion at anytime during the one-touch operation, press the control a second time. To open power sunshades andpanoramic Vista Roof™: Press and release the control to open the sunsh...

detect an object, signaling the door to stop and reverse, does not meetcurrent U.S. federal safety standards. For more information, contactHomeLink 威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. ne...

4. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually near where the hangingantenna wire is attached to the unit). 5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.) Note...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

Opening and Closing the power liftgate: WARNING: Make sure all persons are clear of the power liftgate area before using the power liftgate control. WARNING: Keep keys out of reach of children. Do not allow children to play near an open or moving power liftgate. The liftgate will only operate with t...

To power close the liftgate withthe rear cargo area controlbutton: Press and release the control on theleft rear quarter panel to close theliftgate. Note: The rear cargo area control button is disabled when the liftgateis latched. WARNING: Keep clear of the liftgate when activating the rear switch. ...

WARNING: Make sure that the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive withthe liftgate door open, keep the vehicle well ventilated so outside aircomes into the vehicle. Liftgate ajar ...

Cargo net (if equipped) The cargo net secures lightweightobjects in the cargo area. Attach thenet to the loops and anchorsprovided. WARNING: This net is not designed to restrain objects during a collision. Utility hook The utility hook can be used tohang small items such as grocerybags, etc. Do not ...

ROOF RACK SYSTEM (IF EQUIPPED) Loads should never be placed directly on the roof panel. For properfunction of the roof rack system, loads must be placed directly oncrossbars affixed to the roof rack side rails. Your vehicle may beequipped with factory-installed crossbars. Ford Genuine Accessorycross...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and the transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a ...

CHILDPROOF DOOR LOCKS • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one ...

Opening front windows and panoramic roof (if equipped) You can open the vehicle’s windows, and (if equipped) vent thepanoramic roof by using the control on the transmitter. Refer to Power windows in the Driver Controls chapter for more information. Locking the doors 1. Press and release to lock all ...

Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash for a maximum of three minutes. Press again or turn theignition to the on position to deactivate, or wait for the alarm to time outin three minutes. Note: The panic alarm will only operate when the ...

3. A tone will be heard when the deactivation is complete.4. Repeat this procedure for another Integrated Keyhead Transmitter ifdesired. Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin...

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter or the keyless entry system keypad isused to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the on position, or • ...

to be repeated. If the procedure needs to be repeated, wait a minimumof 30 seconds before beginning again. 1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the onposition to the of...

• The battery saver will shut off the headlamps 10 minutes after theignition has been turned to the off position. SECURICODE™ KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • recall memory seat/power mirrorspositions. The keypad can be ope...

Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. All personal codes are now erased and only the factory set 5–digit ...

Automatic arming The vehicle is armed immediately after switching the ignition to the offposition. The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the onpositi...

If the key has been successfully programmed it will start the vehicle’sengine and will operate the remote entry system (if the new key is anIntegrated Keyhead Transmitter). The theft indicator light will illuminatefor three seconds and then go out to indicate successful programming. If the key was n...

• Press the driver or passengerinterior door lock control whilethe door is open, then close thedoor. • Press the 7 • 8 and 9 • 0 controls on the keyless entry pad(if equipped) at the same time tolock the doors (driver’s door mustbe closed). There is a 20 second countdown when any of the above action...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front power seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of ...

The control is located on the outboard side of the seat cushion. Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Tilt Function Move the switch in the direction ofthe arrows to tilt the seat forward orbackward. Power recline (if equipped) Press the contro...

Memory seats and power mirrors This system allows automaticpositioning of the driver seat andpower mirrors to two programmablepositions. The memory seat control is locatedon the driver door. • To program position 1, move thedriver seat and mirrors to thedesired position using theassociated controls....

If the engine falls below 350 RPMs while the cooled seats are on, thefeature will turn itself off and will need to be reactivated. Climate controlled seats air filter replacement The climate controlled seat system includes air filters that must bereplaced periodically. Refer to the scheduled mainten...

Folding down the 60/40 rear seats Note : The head restraints should be placed in the full down position before folding the seatback down. Note : Ensure that no objects such as books, purses, or briefcases are on the floor in front of, on or under the second row seat cushion beforeactuating the relea...

Press and hold the controlmechanism to lower the seatback.The top portion lowers the right(40%) seatback, and the bottomportion lowers the left (60%)seatback. Returning the 2nd row seatback to the upright position WARNING: Before returning the seatback to its original position, make sure that cargo ...

Seat-mounted armrest and cupholders Your vehicle is equipped with a rearseat armrest. To fold the armrestdown, release the latch located onthe seatback by pressing down andpulling forward. To access the cup holders, lift upone of the slotted areas on thecover. WARNING: Use only soft cups in the cuph...

SAFETY RESTRAINTS Personal Safety System 姞 The Personal Safety System 威 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

longitudinal deceleration. The pretensioners are designed to activate infrontal and near-frontal collisions, and in rollovers and side collisionswhen the Safety Canopy 威 is activated. Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor...

WARNING: Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off the frontpassenger airbag and passenger seat-mounted side airbag. The system isdesigned to help protect small...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, driver seatposition sensor, and front passenger sensing system. In addition, theRCM also monitor...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle. All restraints in the vehicle are combination lap and shoulder belts. While you are fastened in the safety belt, the combination lap/shoulderbelt adjusts to your movement. However, if you brake hard, turn hard, orif your v...

Webbing extraction sensitive mode The webbing sensitive locking mode locks the webbing and preventsmore belt from being pulled out if the belt is pulled out too quickly. Thebelt will unlock when you stop pulling on it. Automatic locking mode How to use the automatic locking mode • Buckle the combina...

How to disengage the automatic locking mode WARNING: Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify thatthe ⬙ automatic locking retractor ⬙ feature for child seats is still worki...

WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safetybelt and increase the risk of injury in a collision. Second row comfort guide The second row outboardla...

WARNING: Position the safety belt comfort guide so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safetybelt and increase the risk of injury in a collision. Safety belt extension assembly If the safety belt is ...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximatelyone minute while the vehicle istraveling at least 3 mph(5 km/h) and more than1-2 minutes have elapsed sincethe ignition switch has beenturned to on... The Belt-Minder 威 feature is activated - the safety belt...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are deactivated/activated independently. When deactivating/activatingone seating position, do not buckle the other position as this willterminate the process. Read Steps 1 - 4 thoroughly before proceeding ...

4. Within approximately seven seconds of the light turning off, bucklethen unbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light willflash four times per second for three seconds. •...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the cond...

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-fro...

How does the Safety Canopy 姞 system work? The design and development of theSafety Canopy 威 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

• The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your an authorized ...

WARNING: All children are shaped differently. The Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safetyorganizations or are the minimum requirements of law. Fordrecommends checking with a NHTSA Certified Child Passenger Safety...

Recommendations for attaching child safety restraints for children Re-straintType Child Weight Use any attachment method as indicated be- low by “X” LATCH(loweran-chorsandtoptetheran-chor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safet...

Transporting children Always make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are shapeddifferently. The child height, age and weight thresholds provided arerecommendations or the minimum requirements of law. The NationalHighway T...

SAFETY SEATS FOR CHILDREN Infant and/or toddler seats Use a safety seat that is recommended for the size and weight of thechild.When installing a child safety seat: • Review and follow the informationpresented in the Airbag supplemental restraint system(SRS) section in this chapter. • Carefully foll...

Combining safety belt and LATCH lower anchors for attachingchild safety seats When used in combination, either the safety belt or the LATCH loweranchors may be attached first, provided a proper installation is achieved.Attach the tether strap afterward, if included with the child seat. Referto Recom...

For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, , otherwiseroute the tether strap over the top of the head restraint. If the top of thesafety seat hits the adjustable head restraint, raise the head restraint tolet the...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO CROSSOVER VEHICLE OWNERS Crossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on streets, highwaysand off-road. Crossover vehicles arenot designed for cornering at speedsas high as passenger cars any morethan low-slung sports cars ar...

driving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other than those conditions could subject the vehicle to excessivestress which might result in damage which is not covered under yourwarranty. For AWD vehicl...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance andlonger tire life. • Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(fro...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, thenthe load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now yo...

Do not exceed the maximum loads listed on the Safety ComplianceCertification label. For load specification terms found on the label, referto Vehicle loading — with and without a trailer in this chapter. Remember to figure in the tongue load of your loaded vehicle whenfiguring the total weight. FWD G...

Preparing to tow Use the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. Contact your authorized dealer or areliable trailer dealer as soon as possible if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to ...

cause them not to function properly. Your lamp outage featuremay also be disabled or provide incorrect information. Trailer tow connector(equipped on vehicles with a Class II trailer tow/prep package) The trailer tow connector is located under the rear bumper, on thedriver’s side of the vehicle. Ref...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • If you are driving down a long or steep hill, shift to a lower gear...

All Wheel Drive (AWD) vehicles: Tow your All Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a vehicle transport trailer. Do not tow your All Wheel Drive vehicle with the front wheels offthe ground (by using a tow dolly) and the rear wheels on thegr...

STARTING Positions of the ignition 1. Off— locks the automatictransmission gearshift lever andallows key removal. This positionalso shuts the engine and allelectrical accessories off withoutlocking the steering wheel. To lockthe steering wheel, remove the keythen turn the steering wheel. 2. Accessor...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

Electronic Stability Control (ESC) Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for example when cornering severelyor avoiding objects in the roadway. ESC operates by applying brakes toone or more of the wheels individually and, if nece...

STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until itstops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level(below the MIN mark on the reservoir)...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have anintegrated convex spotter mirrorbuilt into the upper outboard cornerof the outside mirrors. They aredesigned to assist the driver byincreasing visibility along the side ofthe vehicle. For more information onyour side view mirrors, refer to E...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. With the AWD option, power will be delivered to the frontwheels and distributed to the rear wheels as needed. The AWD system isactive all the time and requires no input from the oper...

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through high w...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slip...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. This switch is located behind apanel on the left side of the...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 38 20A Subwoofer/amplifier 39 20A Radio 40 20A Not used (spare) 41 15A Automatic dimming rear viewmirror 42 10A Not used (spare) 43 10A Rear wiper logic 44 10A Customer accessory feed 45 5A Front wiper logic 46 7.5A Occupant classification senso...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (...

Removing the spare tire and jack 1. Lift the carpeted load floor panellocated in the rear of the vehicle. 2. Remove the spare tire cover (ifequipped). 3. Remove the wing nut securingthe spare tire by turning itcounterclockwise. 4. Remove the plastic washer. 5. Lift and remove the temporaryspare tire...

If you are stowing a flat 22 inch tire and wheel assembly, temporarily remove the load floor, plastic stowage bins, and the foamload floor supports to make space for the 22 inch tire and wheelassembly. Place the 22 inch tire & wheel assembly in the spare tire wellwith the valve stem facing down....

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth, then use a clean and dry white cottoncloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instr...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the rin...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the secondary hood latchthat is located under the frontcenter of the hood. 3. Lift the hood and support it with th...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer flu...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil ...

6. Wipe the dipstick clean. Insertthe dipstick fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. Maintenance and Specif...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the dipstick back in and...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quar...

• NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection cha...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certainconditions. Care should be taken to avoid inhaling excess fumes. WARNING: The flow of fuel through a fuel pump no...

Fuel filler cap When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise until it spins off. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on thefiller pipe. 5. Turn the filler cap cl...

Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leadedfuel or any other fuel. The use of leaded fuel is prohibited by law andcould damage your vehicle. Your vehicle was not designed to use fuel or ...

empty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might no...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (...

If the vehicle’s engine or transmission has just been serviced, or thebattery has recently run down or been replaced, the OBD-II system mayindicate that the vehicle is not ready for I/M testing. To determine if thevehicle is ready for I/M testing, turn the ignition key to the on positionfor 15 secon...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does notconsume fluid. However, the fluid level should be checked if thetransmission is not working properly, i.e., if the ...

The transmission fluid should bewithin the cross-hatch area if atnormal operating temperature180°F-200°F (82°C-93°C) . High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/or poss...

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Release the clamps that securethe air filter housing cover. 2. Carefully separate the...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for yourvehicle through your local Lincoln or Ford of Canada dealer. Thesequality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to comp...

Peace of mind Remote start Keyless entry keypad Cargo security shade Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................63 AdvanceTrac ..............................209 Air cleaner filter ...............297–299 Air conditioning ..........................40 Airbag supplemental restraintsystem ........................134, 143, 146 and child safety seats ............136descrip...