Lincoln 2003 - Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possibledamage to others, your vehicle and its equipment? In this guide, answersto such questions are contained in comments highlighted by the warningtriangle symbol. These comm...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicl...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

If the light remains on, have your vehicle serviced at the first available opportunity. Note: The light will illuminate if vehicle refueling is conducted with the engine running. Never refuel vehicle with the engine running. Light is blinking: Engine misfire is occurring which could damage your cata...

position to the START position, the light will momentarily illuminate justprior to reaching the START position). If the light remains on, continuesto flash or fails to illuminate, have the ABS serviced immediately. If theABS light remains on, it means the anti-lock brake system hasmalfunctioned and ...

Speed control Illuminates when the speed controlis activated. Engine coolant temperature Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as safely possible,switch off the engine and let it cool. Never remove the coolant recovery cap while the engine isrunning or hot. ...

AWD locked (if equipped) Illuminates when all wheel drive(AWD) is locked. If the lightcontinues to flash have the systemserviced. Safety belt warning chime Sounds to remind you to fasten your safety belts. BeltMinder 姟 chime Sounds intermittently to remind you to fasten your safety belts. Supplement...

Fuel gauge Displays approximately how muchfuel is in the fuel tank. The fuelgauge may vary slightly when thevehicle is in motion or on a grade. When refueling the vehicle fromempty indication, the amount of fuelthat can be added will be less thanthe advertised capacity due to thereserve fuel. If the...

Tachometer Indicates the engine speed inrevolutions per minute. Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt)USA English (fus) Instrument Cluster 17

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. Tape eject control 2. CD eject control 3. Bass/treble control 4. Balance/fade control 5. Compression/shuffle control 6. Select control 7. Side direction/Dolby control 8. Rewind/fast forward control 9. RDS/Mute control 10. Autoset control 11. Scan control 12...

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. Audio power can also be turned on by pressing the AM/FM select controlor the TAPE/CD select control. Speed sensitive volume...

Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold f...

Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on thetape. (The tape scans in a forward direction. At the end of the tape’sfirst side, direction automatically reverses to the opposite side of thetape.) To stop on a particular selection, press the control...

Fast forward The fast forward control works intape and CD modes. • In the tape mode, tape directionwill automatically reverse whenthe end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within thecurrent track. Tape direction select Press to play the alternate side of...

Compression adjust Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activateand deactivate compression adjust. Radio data system (RDS) feature This feature allows your audio system to receive station identification orprogram ...

Program type • Press the RDS control until theFIND program type is displayed. • Use the SEL control to select theprogram type. With the featureon, use the SEEK or SCANcontrol to find the desiredprogram type from the followingselections: • Classic • Country • Info • Jazz • Oldies • R & B • Religi...

Soft mute When the vehicle is in reverse, and an obstacle is detected by Rear ParkAssist, the radio volume is reduced to a level that allows the warning tobe heard. After the obstacle warning is gone, the radio will return to thepreviously set volume level. Setting the clock Your vehicle is equipped...

Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on theCD. (The CD scans in a forward direction, wrapping back to the firsttrack at the end of the CD.) To stop on a particular selection, press thecontrol again. Radio station memory preset The radio is equipp...

If there are fewer than six strong stations available on the frequencyband, the remaining memory preset controls will all store the last strongstation available. To deactivate autoset and return to your audio system’s manually setmemory stations, press the AM/FM control again. CD select CD mode may ...

has been loaded, the door will close and the CD will begin to play. Forexample, to load a CD into slot 2, press the LOAD control and then presspreset 2. Auto load This feature allows you to autoloadup to 6 discs into the multi disc CDplayer internal to the radio.Press and hold the LOAD control until...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the BASS control. Use theSEL control to increase or decreasethe amount of bass. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Press ...

If RDS is turned ON , you can access the following: • TRAFFIC ON/OFF-Refer to Traffic announcements. • FIND type-Refer to Program type. • SHOW (NAME, TYPE, NONE)- Refer to Radio data system feature. • RDS ON— Refer to Radio data system feature. You can also access COMP ON/OFF. TRAFFIC ON/OFF— Traffi...

RDS traffic scan feature When in traffic mode, you can use the SCAN feature to scan up thefrequency band for listenable traffic capable frequencies. With the RDS activated, press the MENU control until TRAFFIC ON isdisplayed. Press the SCAN control. SCAN TRAFFIC will display. Theaudio system will sc...

Program type This feature allows you to search for RDS stations selectively by theirprogram type. Press the MENU control until FINDprogram type is displayed. Use the SEL control to select theprogram type. With the feature on,use the SEEK or SCAN control tofind the desired program type from the follo...

Press DSP to access the ambiancemenu. Press SEL toengage/disengage. Turn the volume control toincrease/decrease the level ofambiance. Press the DSP control again to access the occupancy modes. Use theSEL control to optimize the sound based upon the occupants in thevehicle. The following occupancy mo...

AUDIO SYSTEM WARRANTY AND SERVICE Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. LINCOLN NAVIGATION SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Lincoln Navigation System whichallows you to listen to th...

5. MENU : Press to access system settings such as display, brightness, clock mode, etc. 6. CD OPEN CLOSE : Press to open/close the display screen and access the CD player. Cold temperature advisory When operating the system below 32° Fahrenheit (0° Celsius), thedisplay screen requires 20–30 minutes ...

3. Select AM, FM1 or FM2. 4. Press TUNE to adjust manually up ( ) or down ( ) the frequency band. 5. Press SEEK to find the next strong station up ( ) or down ( ). Note: If PTY (program type) is selected, the station selection will be limited. Refer to Program Type (PTY) for further information. To ...

To use the Navigation system: 1. Ensure that the vehicle ignition is on, and the navigation DVD isloaded into the navigation DVD player. Refer to Loading the map DVD for navigation DVD locations. 2. Press DEST. The warning screen will appear. After reading, pressAGREE. The screen will show a map wit...

To adjust the voice guidance volume: Press On/Off to turn the voiceguidance option on/off. Use thenumeric keys (1–7) to determinethe volume level of the guidancevoice prompts. Voice activated commands (if equipped) Your Lincoln Navigation System (LNS) may be equipped with a voiceactivated feature wh...

• Detour While in navigation map mode, the following commands are available byvoice activation: • Gas station • Gas • Hospital • Police station • Restaurant • Hotel Audio mode Your Lincoln Navigation Audio System has many features including a fullrange of audio functions. To access these functions, ...

2. The navigation screen will fold down, allowing you access to thein-dash six CD system. 3. Press LOAD and the desired CD slot number. The indicator light willblink slowly at first, then quickly, signaling the system is ready. 4. Insert a disc. 5. To load more than one disc , press and hold LOAD. T...

Pause In CD mode, press PAUSE to pausethe current track. Press again tocontinue playing. Map mode Map display information To access the map display, press MAP on the bezel. Once pressed, the current mapdisplay will appear on the screenshowing the current vehiclelocation. Zoom control When ’Zoom’ is ...

• touch one of the arrow buttons repeatedly for the map to be displayedagain at the final zoom level. • touch one of the segments of the scale indicator for the map to bedisplayed at the selected zoom level. Additional map function buttons To initiate the display of additionalmap function buttons, t...

Screen symbols Navigation symbol — Indicates the current vehicle position andpoints to the direction in which thevehicle is currently traveling. Destination symbol — Indicates the current route destination. Next turn symbol — Shows the next maneuver that will need to betaken on the current route. No...

Way point symbol — Indicates the location of a way point (locationsyou wish to visit in route to yourultimate destination) on the map. Home position symbol — Indicates the location on the map, currentlystored as the home position. Stored location symbol — Indicates the location of a memorypoint. Thi...

Depending upon whether or not a route is active will determine if routeoptions/route preferences is contained on the Navigation Menu. Route options (destination entered) Once in navigation mode and aroute is currently active, press“Chng. route” to access the ROUTEOPTIONS screen. Choose from thefollo...

On route scroll The system automatically scrollsthrough the entire plannednavigation route either forwards orbackwards. To activate, press thearrow buttons at the bottom left ofthe map screen. Voice guidance/volume Allows you to turn the voiceguidance option on/off and todetermine the volume level o...

Search area Your navigation system uses aregional search area. This area isthe area from which navigationaldirections will be used. To checkyour area or reset, press CHANGEunder the search area listing. Themap will open and allow you toselect another regional area. Ensurethat your search area is cor...

Adding a home location • Select the desired menu item youwish to set as Home (Address,Memory Point, Point of Interest,Previous Destination). • Enter the required details. • Press OK to set the homeposition. To view the set home position: From the stored locations menu with home selected, press LIST ...

Freeway Entrance/Exit Select “Freeway Entrance/Exit”from the second page of theDestination Entry menu. Followthese steps: 1. Enter freeway name — Enter the freeway name using thekeyboard. Press “List” to select afreeway from those displayed. To enter numbers in the freewayname, press “Sym”. 2. Selec...

Special memory points There are five possible memorypoints that you can set. To set a memory point: • Press MAP. • Press “Nav Menu”. • Press “Stored locations”. • Press “Special Memory Point”. • Select “Add” and input destination. • Press OK to confirm. To delete a memory point: • Press “Delete”. Th...

When not using the headphones,shut them off to preserve batterypower. The headphones willautomatically turn off after fiveminutes if they have not received aninfrared audio signal from theoverhead pod. Ensure that the line of sightbetween the headphone andinfrared transmitter (mounted onthe DVD hous...

Do not use the navigation system to locate emergency services.For road safety reasons, the driver should program the system only whenthe vehicle is stationary. Certain functions will therefore not operatewhile the vehicle is in motion.The map database DVD does not reflect road detours, closures orco...

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM 1. A/C control 2. Recirculated air control 3. Passenger temperature control 4. Rear defrost control 5. DUAL control 6. Defrost control 7. Floor & Defrost control 8. Floor control 9. Panel & floor control 10. Panel control 11. OFF control 12. A...

• Off-Outside air is shut out and the fan will not operate. This mode willreduce undesirable odors from entering the vehicle but may increasethe possibility of interior window fogging. • Panel - Distributes outside or recirculated air through the instrumentpanel registers. The A/C compressor will on...

• Do not place objects under the front seat or over the defroster ducts.They may reduce visibility, fall into the ducts, or degrade theperformance of your climate control system. Do not place objects on top of the instrument panel, as theseobjects may become projectiles in a collision or sudden stop...

Controls the direction of the airflowin the rear of the vehicle. WhenFloor is selected, airflow will bedirected through the floor registers.When Panel is selected, airflow isdirected through the overhead registers. Press the mode selector once toselect air distribution through theoverhead vents. The...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position toturn on the parking lamps. Rotateclockwise to the second position toalso turn on the headlamps. Foglamp control The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlamp control is...

Autolamp exit time delay, manual sequence This option allows you to change the length of the autolamp exit delay. To program the auto lamp exit time delay: 1. Start with the ignition in OFF and the autolamps selected. 2. Deselect the auto lamps. 3. Put the ignition on RUN. 4. Put the ignition in OFF...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. • Turn signal will shut offheadlamps, in DRL equippedvehicles, in daytime driving. INTERIOR LAMPS Front row map lights (if equipped) To turn on the map lights, press theedge of the light. Sec...

Third row courtesy/reading/cargo lamps The dome portion of the lamp, thecenter light, can be turned on whenthe headlamp control is rotated fullyup or when an door is opened. With the ignition key in the ACC or ON position, the rear dome lamp canbe turned ON or OFF by sliding the control. BULBS Repla...

Function Number of bulbs Trade number Fog lamp 2 9140 Liftgate lamp 4 916 High-mount stop lamp 32 LEDS 2C54–13A613** Rear license platelamp 2 168 Mirror turn signallamp 2 906 Approach lamp 2 912 Cargo lamp 1 211-2 Interior overhead lamp 1 912 (906) Map lamps 2 168 (T10) Front footwell light 2 194 Al...

Replacing headlamp bulbs To remove the headlamps from the vehicle to change the HIGH BEAMbulb: 1. Make sure the headlamp switch isin the OFF position, then open thehood. 2. Remove the plastic radiator coverover the headlamps by grasping therear edge of the cover and pullingup and toward you. This wi...

1. Push the bulb straight in,carefully aligning the plastic tabs inthe base of the bulb with theopenings in the plastic ring. 2. Rotate the bulb clockwise until itstops. 3. Reconnect the electricalconnector to the bulb. 4. Install the headlamp on thevehicle by aligning the four plastic projections i...

Replacing front parking lamp/turn signal/sidemarker bulbs To remove the headlamps from the vehicle and to change the front turnsignal lamp bulbs: 1. Make sure the headlamp switch isin the OFF position, then open thehood. 2. Remove the plastic radiator coverover the headlamps by grasping therear edge...

Approach lamp/mirror turn signal bulb removal To change the bulbs: 1. Make sure the headlamp switch isin the OFF position. 2. Remove the approach lamp/turnsignal lens from the mirror housingusing a standard flat screwdriver topry the lamp assembly out. 3. Pull the lens out to remove itfrom the mirro...

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals. Push (tap) the end of the st...

Changing the wiper blades It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the blade dow...

CLOCK Press the right control to increasethe time displayed. Press the left control to decreasethe time displayed. AUXILIARY POWER POINT (IF EQUIPPED) Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper use of the power ou...

Another auxiliary power point islocated on the right rear quarterpanel. The power point is accessiblefrom the liftgate. The maximum current draw of any single power point should not exceedit’s fuse rating, otherwise this will result in a blown fuse. Do not use the cigarette/cigar lighter element in ...

The following views are the driver’s side switches: Normal operation • Push down (to the first detent)and hold the top portion of theswitch to open. • Pull up (to the first detent) andhold the top portion of the switchto close. The following view is the powerwindow switch on the rear door trimpanels...

One touch up or down This feature is present on the driver’s window only. To operate ONE TOUCH DOWN: • Press the switch completely downto the second detent and releasequickly. The driver’s window willopen fully. Momentarily press theswitch to any position to stop thewindow operation. If the switch i...

up with no bounce-back protection. If the switch is released before the window reaches fully closed or the ignition is turned OFF (withoutaccessory delay being active), the window will stop. Security overridecan be used if there is ice on the window or seals, causing a restriction. Window lock The w...

Press the control to turn the mirrorOFF or AUTO. The mirror will automatically returnto the normal state whenever thevehicle is placed in R(Reverse)(when the mirror is on) toensure a clear view when backingup. Power side view mirrors The ignition must be in the ACC or ON position to adjust the power...

Reverse tilt down mirrors The side mirrors tilt down when thevehicle is put in R (Reverse). The reverse mirror feature can be turned ON and OFF through the Message Center in this chapter or by using the following key sequence. This procedure must be performed within 20 seconds. 1. Insert the ignitio...

SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph). Do not shift the gearshift leverinto N (Neutral) with the speedcontrol on. Do not use the speedcontrol in heavy traffic or on roads that are winding,slippe...

To set a lower set speed • Press and hold SET −. Releasethe control when the desiredspeed is reached or • Press and release SET − tooperate the Tap-Down function.Each press will decrease the setspeed by 1.6 km/h (1 mph) or • Press CNCL or depress the brakepedal. When the desired vehiclespeed is reac...

To disengage speed control • Press CNCL, or • depress the brake pedal. Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt)USA English (fus) Drive...

To return to a previously set speed • Press RES. For RES to operate,the vehicle speed must be fasterthan 48 km/h (30 mph). Indicator light This light comes on when thevehicle speed control is engaged andactively controlling vehicle speed. STEERING WHEEL CONTROLS These controls allow you to operate s...

In AM, FM1, or FM2 mode: • Press MEM to select presetstations within the selected radioband. In Tape mode: • Press MEM to select the nextselection on the tape. In CD mode: • Press MEM to select the nextselection on the CD. In any mode: • Press VOL + or − to adjustvolume. Climate control features Pre...

Press FAN + or - to adjust fanspeed. Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation controlfeatures when the vehicle is equipped with the navigation feature. Audio control features Press to select: • AM, FM1, FM2, or • CD. In AM, FM1, o...

Navigation control features Press and hold VOICE until thevoice icon appears to use thenavigation voice guidance. Press RPT (REPEAT) control tohear previous command repeatedfrom the navigation system. Climate control features Press TEMP + or - to adjusttemperature. HOMELINK 姞 WIRELESS CONTROL SYSTEM...

When programming your HomeLink 威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as requ...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing steps 1 and 2outlined in the “Programming” section, replace step 3 w...

Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP menu. Info menu This control displays the followingcontrol displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance to Empty • Average Fuel Economy • Trip Elapsed Drive Time Odom...

Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in liters/100 km ormiles/gallon. If you calculate your average fueleconomy by dividing liters of fuel used by 100 kilometers traveled (milestraveled by gallons used), your figure may be different th...

Warning display Status Low washer fluid level Warning returns after theignition key is turned fromOFF to ON. Check AdvTrac (if equipped) Check AWD (vehicles equipped withAdvanceTrac 娂 only) AWD Disabled (vehicles equipped withAdvanceTrac 娂 only) Check fuel cap Oil change required CHECK PARK ASSIST. ...

DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Oil life • Charging system • Door sensor • Washer fluid • Brake fluid • Compass • Outside temperature • Engine sensor Contact your dealer as soon as possible if the...

POSITIVE RETENTION FLOOR MAT Position the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in. Make sure thatthe mat does not interfere with theoperation of the accelerator or thebrake pedal. To remove the floormat, reverse the installationpro...

Always close liftgate window before opening liftgate. Liftgateglass and liftgate should never be open at the same time. Failure to observe this warning may result in personal injury or damage toyour vehicle. Make sure the liftgate door and/or window are closed to preventexhaust fumes from being draw...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are notdesigned for cornering at speeds as high as passenger cars any morethan low-slung sport cars are designe...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key with you in a safe place in caseyou require it in an emergency.Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCKS ...

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The remote entry system allows you to lock or unlock all vehicle doorsand liftgate and open the liftgate window without a key. The remote entry lock/unlock ...

Associating the transmitter with the memory seat feature To activate this feature: 1. Select the desired memory position by pressing the memory 1 or 2button on the memory SET control, located on the instrument panel tothe left of the steering wheel. 2. Press the memory SET button. 3. Press any butto...

To replace the battery: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in the same orientation.Refer to the diagram inside thetransmitter unit. 3. Snap the two halves back...

Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Turn ...

Illuminated entry The interior lamps illuminate when the remote entry system is used tounlock the door(s). The system automatically turns off after 25 seconds or when the ignitionis turned to the ON or ACC position. The dome lamp control (ifequipped) must not be set to the OFF position for the illum...

Deactivating/activating the autolock feature The autolock feature may be deactivated/activated by selecting theautolock function (accessed by pressing the SETUP control). Press theRESET control to turn the autolock function ON or OFF. Refer to Message center in the Driver controls chapter for additi...

Programming your own personal entry code To program your own code: 1. Enter factory set code (keypad will illuminate when pressed). 2. Press 1/2 control within fiveseconds of step 1. 3. Enter your personal 5 digit code.Enter each digit within five secondsof previous one. 4. After the code is entered...

Anti-scan feature The anti-scan feature preventsrepeated attempts at arriving at avalid key code. The keyless entry pad is disabled for1 minute after 7 unsuccessfulattempts at entering a valid keycode. The keypad will flash duringthis 1 minute mode. However, the7/8 and 9/0 controls will still lockth...

Locking the doors with the keyless entry system It is not necessary to enter thefactory or personal code prior tolocking all doors. To lock the doors: • with the driver’s door closed,press the 7/8 control and the 9/0control at the same time. Activating/deactivating autolock with the keyless entry sy...

The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems mayresult in vehicle starting problems and a loss of security protection. THEFT INDICATOR The theft indicator is the flashing red indicator located on the dashpanel. • Wh...

The following items may prevent the vehicle from starting: • Large metallic objects • Electronic devices on the key chain that can be used to purchasegasoline or similar items • A second key on the same key ring as the coded key If any of these items are present, you need to keep these objects fromt...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using yourremote entry transmitter. • Unlock the doors by using yourkeyless entry pad. • Unlock the driver’s door with a key. Turn the key full travel (towardthe front of the vehicle) to make sure t...

SEATING Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it i...

Using the power lumbar support The power lumbar control is locatedon the door panel. Press one side of the control toadjust firmness. Press the other side of the control to adjust softness. Using the manual recline function Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not...

Adjusting the power front seats – door mounted controls The controls for the power seats are located on the inside of each frontdoor. Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden sto...

Press to move the rear portion ofthe seat cushion up or down. Memory seats/rearview mirrors/adjustable pedals This system allows automaticpositioning of the driver seat,outside rearview mirrors, andadjustable pedals to twoprogrammable positions. The memory seat control is locatedon the instrument pa...

Deactivating/activating the easy entry/exit feature The easy entry/exit feature may also be turned on and off using thefollowing key sequence. This procedure must be performed within 20seconds. 1. Remove the key from the ignition (if currently inserted). 2. Insert the ignition key into the ignition ...

To remove climate controlled seatair filter: • Remove key from ignition. • Push on the outside rigid edge ofthe air filter at the center androtate toward the front of thevehicle once tabs are released. • Remove filter. To install climate controlled seat air filter: • First, position the filter in it...

The head restraints can be raised bylifting. If the head restraint is fullylowered, press the release button toraise it. To raise or lower the headrestraint, press the release buttonlocated on the side of the metal bar. If the head restraint becomes detached, replace the notched bar into theholes wh...

3. To return the seat to a seatingposition, flip the seat into theupright position. 4. Make sure the seat is latched tothe floor. If the seat is not firmly latchedto the floor, the seat back willnot lock in the upright position.To adjust, you must unlatch theseat from the floor and retry. To exit th...

Folding the middle 2nd row seat (If equipped) 1. Locate the lever on the top of theseatback. 2. Pull the lever up and push theseatback toward the front of thevehicle. 3. Press down on the top outboardarea of the seatback until a click isheard. To return the seatback to theupright position: 1. Pull t...

2. Pull the seat release lever locatedon top of the seatback while liftingthe seatback into the uprightposition. 3. The seatback will latch into place. The third row seat is equipped with combination lap and shoulder beltsin both seating positions. For information on the proper operation of thesafet...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on t...

• Front and rear seats All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengtha...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, allsafety belts should be checked for proper function. Failure to replacethe belt and retractor assembly could incre...

BeltMinder The BeltMinder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriver that the driver’s safety belt is unbuckled by intermittentlysounding a chime and illuminating the safety belt warning lamp in theinstrument cluster....

recommends that all safety belt assemblies used in vehicles involved in acollision be replaced. However, if the collision was minor and a qualifiedtechnician finds that the belts do not show damage and continue tooperate properly, they do not need to be replaced. Safety belt assembliesnot in use dur...

Children and air bags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Air bags can...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

The Safety Canopy 娂 is mounted to the roof side-rail sheet metal, behind the headliner, above the first and second row seats. In certain lateralcollisions or rollover events, the Safety Canopy 娂 system will be activated, regardless of which seats are occupied. The Safety Canopy 娂 is designed to infl...

Any difficulty with the system is indicated by one or more of thefollowing: • The readiness light (same light as for front air bag system) will eitherflash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone ...

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions tha...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh soldas shelf or carpet liner under the booster seat...

Installing child safety seats with combination lap and shoulderbelts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. Children 12 and ...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3...

3. Turn the key to 3 (ON) withoutturning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever yo...

Brake Assist (if equipped) The Brake Assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal andmaximizes the amount of brake booster assist, helping the driver toachieve maximum braking pressure. Once a panic brake application isde...

when the system is active and an indicator light in the control buttonthat will illuminate when the system is turned off. In vehicles with amessage center, the message “ADVANCETRAC OFF” will be displayed. If a failure is detected in the AdvanceTrac 娂 system, the warning indicator light in the instru...

Driving with a 5–speed automatic transmission Your transmission is equipped with an adaptive learning strategy found inthe vehicle computer. This feature is designed to increase durability, andprovide consistent shift feel over the life of the vehicle. A new vehicle ortransmission may have firm and/...

2 (Second) Use 2 (Second) to start-up onslippery roads or to provideadditional engine braking ondowngrades. 1 (First) • Provides maximum enginebraking. • Allows upshifts by movinggearshift lever. • Will not downshift into 1 (First)at high speeds; allows for 1(First) when vehicle reachesslower speeds...

dirt (do not clean the sensors with sharp objects). If the sensorsare covered, it will affect the accuracy of the system. If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarm...

SETUP, AWD <LOCKED> will be displayed. AWD <LOCKED> providespower to all four wheels constantly which allows you to operate yourvehicle in severe winter or off-road conditions such as deep snow, iceor shallow sand. It is not recommended that you use AWD <LOCKED>on dry pavement. • A...

• To disable AWD, press RESET. The system will go back to AWD AUTOmode momentarily, then the AWD LOCKED indicator light will flash inthe instrument cluster eight times every two minutes. The display willthen show AWD <DISABLED> LOCKED for four seconds and thenturn off. • If a serious problem o...

Basic operating principles • Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle. • Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehi...

If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary. Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced. After driving through mud, ...

Tires, Replacement Requirements Do not use a size and type of tire and wheel other than thatoriginally provided by Ford Motor Company because it can affect the safety and performance of your vehicle, which could result in anincreased risk of loss of vehicle control, vehicle rollover, and/or seriousp...

Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired. Check tire pressure with atire gauge every few weeks(including spare). Safe operationrequires tires that are neitherunderinflated nor a vehicle which ...

• Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It isdetermined by subtracting the weight of the loaded trailer towingvehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the tr...

Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken whendriving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than mostpasse...

• Service your vehicle more frequently if you tow a trailer. Refer to thesevere duty schedule in the scheduled maintenance guide. • Do not tow a trailer until your vehicle has been driven at least 800 km(500 miles). • Refer to the instructions included with towing accessories for theproper installat...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safeif installed properly and adjusted to the manufacturer’s specifications. Thetrailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s br...

Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance guide formore information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the veh...

RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficie...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switc...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link ca...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Moonroof, Driver seat switch 2 10A VAPS module, Memory seat module,Body security module, TPMS 3 20A Radio, Navigation 4 5A Front wiper module 5 15A Flasher relay (turn/hazards) 6 5A...

Auxiliary relay box The relay box is located on the frontright fender well underneath thespeed control module. The relays are coded as follows: Fuse/Relay Location Description Relay 64 Right HID relay Relay 65 Left HID relay Relay 66 EDF relay Rear relay box The relay box is located on the rear pass...

The use of tire sealants is not recommended and maycompromise the integrity of your tires. The use of tire sealants may also affect your tire pressure monitoring system (if equipped). If your vehicle is equipped with a tire pressure monitoringsystem, refer to Tire Pressure Monitoring System (if equi...

Note: Passengers should not remain in the vehicle when the vehicle isbeing jacked. 4. Block the wheel that is diagonallyopposite of the flat tire using thewheel chock provided with yourvehicle. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following...

3. Remove the tools from theprovided bag. Rotate the wrench socket out fromthe handle. Removing the spare tire Do not use an impact wrench on the winch drive nut. This willdamage the spare tire winch. 1. Open the cover from the carpeting on cargo floor to expose the winchdrive nut. 2003 Aviator f/k/...

2. Insert the lug wrench on thewinch drive nut. The wrench will stop moving andforward resistance to turning will befelt when properly engaged. 3. Turn the wrenchcounterclockwise until the tire islowered to the ground and the cablehas slack. When turning the wrench,make sure that it does not scuff t...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. A...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to the exposedground metal surface accessible on the side of the power steering pumpreservoir bracket, facing the battery. Do not use fuel lines, engine rock...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the authorizeddealer where your vehicle was purchased when warranty repairs areneeded. However, you may also take your vehicle to another...

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action un...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailab...

• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer solution. Be sure to replace wiper blades when theyappear worn or do not function properly. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth. • Avoid cleaners o...

CLEANING THE CLIMATE CONTROLLED SEATS (IF EQUIPPED) Remove dust and loose dirt with a whisk broom or a vacuum cleaner.Remove fresh spots immediately. Clean the seat with a damp cloth, usinga mild soap and water solution, if necessary. LEATHER SEATS Your leather seating surfaces have a clear, protect...

Motorcraft Vinyl Conditioner (Canada only) (CXC-94) Motorcraft Deluxe Leather and Vinyl Cleaner (not available in Canada)(ZC-11–A) Ford Extra Strength Tar and Road Oil Remover* (not available inCanada) (B7A-19520–AA) Ford Extra Strength Upholstery Cleaner (not available in Canada)(E8AZ-19523–AA) Mot...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle. 2. Go to the front of the vehicle andrelease the latch located in thegrille. 3. Lift the hood. 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt)USA English (fus) Maintenance and Specifications 293

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 engines 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Battery 5. Power steering fluid reservoir 6. Engine oil filler cap 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Air filter assembly 200...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL...

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

• A large amount of water without engine coolant may be added, in caseof emergency, to reach a vehicle service location. In this instance, thecooling system must be drained and refilled with a 50/50 mixture ofengine coolant and distilled water as soon as possible. Water alone(without engine coolant)...

Severe climates If you drive in extremely cold (less than –36° C [–34° F]) or extremelyhot climates, it may be necessary to adjust the coolant concentrationlevels. • Extreme cold: increase the coolant concentration above 50%. NEVER increase the coolant concentration above 60%. • Extreme hot: it is a...

Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage. When fa...

splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction. When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely haza...

with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of gasoline. If theproblems persist, see your dea...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

EPA window sticker Every new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. The EPAwindow sticker should be your guide for the fuel economy comparisonswith other vehicles. It is important to note the box in the lower left corne...

Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, trades vehicles, or supervises a fleet of vehic...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

government test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires depends upon the actualconditions of their use, however, and may depart significantly from thenorm due to variations...

• Adjust tire pressure to recommended specifications found on theCertification Label. Tire pressure information can also be found on theTire Information label located on the inside of the fuel filler door. • Check tires for proper air pressure monthly. Check spare tire forproper air pressure every s...

LUBRICANT SPECIFICATIONS Item Ford PartName orequivalent Ford PartNumber FordSpecification Body hinges,latches, doorstriker platesand rotors, seattracks, fuel fillerdoor hinge andspring, hoodlatch, auxiliarylatch, seattracks Multi-PurposeGrease orMulti-PurposeGrease Spray XG-4 orF5AZ-19G209-AA ESR-M...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Automatictransmission 1 MotorcraftMERCON 威 V ATF XT-5-QM MERCON 威 V Power steeringfluid MotorcraftMERCON 威 Multi-PurposeATF XT-2-QDX MERCON 威 Rear axles 75W-140 Highperformancesynthetic rearaxle lubricant XY-75W140–QL WSL-M2C192–A Fro...

ENGINE DATA VEHICLE DIMENSIONS Vehicle dimensions mm (in) (1) Overall length 4909 (193.3) (2) Vehicle width (body) 1877 (73.9) (3) Vehicle width (includingmirrors) 2132 (83.9) (4) Maximum height* 1813.5 (71.4) (5) Wheelbase 2889 (113.7) (6) Track width, front 1547 (60.9) (6) Track width, rear 1554 (...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) Engine number The engine number (the last eight numbers of th...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln, Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desi...

A ABS (see Brakes) .....................219 Accessory delay ........................124 Air bag supplemental restraintsystem ................................196, 200 and child safety seats ............198description ......................196, 200disposal ....................................203driver...

fail-safe coolant ......................304idle speed control ...................299lubricationspecifications ..................323, 325refill capacities ........................321service points ..........................294starting after a collision .........252 Engine block heater ..................

Trip odometer .............................16 Trunk .........................................159 Turn signal ..........................13, 106 V Vehicle dimensions ...................325 Vehicle Identification Number(VIN) ..........................................327 Vehicle loading ...................