Lincoln Electric IM709 - Manuals

Page 2 - SAFETY; WARNING; CALIFORNIA PROPOSITION 65 WARNINGS

FOR ENGINEpowered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors....

Page 5 - PRÉCAUTIONS DE SÛRETÉ

iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1. Protegez-vous contre la seco...

Page 6 - Thank You; Please Examine Carton and Equipment For Damage Immediately

Thank You for selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much pride as we have in bringing this product to you! Read this Operators Manual and any others included with this equipment completely before attempting ...

Page 7 - vi; TABLE OF CONTENTS

vi TABLE OF CONTENTS Page Installation .......................................................................................................................Section A Technical Specifications .......................................................................................................A-1S...

Page 8 - INSTALLATION; ELECTRICAL INPUT REQUIREMENTS

A-1 INSTALLATION DEMO ZONE A-1 TECHNICAL SPECIFICATIONS - Demo Zone (K-1854-1) Voltage Specification Input Connection Specification 230 VAC single phase, 40 amps Type 6-50P plug ELECTRICAL INPUT REQUIREMENTS RATED OUTPUT HEIGHT WIDTH DEPTH WEIGHT 53.00 in. 66.00 in. 53.00 in. 1707 lbs. (w/o gas cyli...

Page 9 - SAFETY PRECAUTIONS; INPUT POWER

A-2 INSTALLATION DEMO ZONE A-2 SAFETY PRECAUTIONS INPUT AND GROUNDING CONNECTIONS INPUT POWER The Demo Zone is designed to operate from 230 volt,60 Hz single-phase input power with 40-amp capacity.A 6-50R type receptacle must be provided by theuser. The receptacle must be installed by a qualifiedper...

Page 11 - HANDLING; GENERAL INSTALLATION REQUIREMENTS; LOCATION; STACKING; CAUTION

HANDLING A pallet jack or forklift truck can be used to move theDemo Zone and to install the caster kit. The place-ment of the pallet jack or forks must balance theDemo Zone load to prevent tipping. FALLING EQUIPMENT can causeinjury. • Do not lift the Demo Zone by over- head crane. • Do not lift the...

Page 12 - OPERATION; GENERAL DESCRIPTION

B-1 OPERATION B-1 GENERAL DESCRIPTION DEMO ZONE The Demo Zone is a compact system to display anddemonstrate welding and cutting equipment. The Demo Zone contains: - Square Wave TIG 175 Power Source - Power MIG 255 Power Source - Ranger 250 Power Source - V350 Pro Power Source - Pro Cut 55 Plasma Cut...

Page 13 - EQUIPMENT LIMITATIONS; DESIGN FEATURES; PLATFORM COMMONALTIES; REGULATORY REQUIREMENTS; WELDING AND CUTTING AREA

B-2 OPERATION B-2 R E C O M M E N D E D E Q U I P M E N T /INTERFACE EQUIPMENT LIMITATIONS The Demo Zone is intended for indoor display anddemonstration use. The Demo Zone is intended forlight duty operation. Because of the input power limita-tion, power sources (except Ranger 250) may only beused a...

Page 14 - WELDER OPERATION; DUTY CYCLE; AUXILIARY POWER OPERATION

B-3 OPERATION B-3 WELDER OPERATION DUTY CYCLE Full output and duty cycle may not be obtained fromall power sources. The output and duty cycle may belimited by the 40 amp input power limitation of theDemo Zone. The duty cycle of the power source mustbe adjusted to be within the capability of the 40 a...

Page 15 - ACCESSORIES

C-1 ACCESSORIES C-1 FAC TO RY I N S TA L L E D O P T I O N S /ACCESSORIES - none F I E L D I N S TA L L E D O P T I O N S /ACCESSORIES CASTER WHEELS C a s t e r w h e e l s , w h i c h a r e p r o v i d e d , a r e a f i e l dinstalled option for the Demo Zone. The 5-inch diame-ter caster wheels off...

Page 16 - MAINTENANCE; ROUTINE MAINTENANCE

D-1 MAINTENANCE D-1 ROUTINE MAINTENANCE Refer to individual Operator’s Manuals for routinemaintenance requirements. Perform the following daily routine: • Check that no combustible materials are in the weld- ing or cutting area or around the machine. • Remove any debris, dust, dirt, or materials tha...

Page 17 - TROUBLESHOOTING

E-1 TROUBLESHOOTING E-1 DEMO ZONE If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed. CAUTION Service and Repair should ...

Page 18 - DIAGRAMS; DEMO ZONE WIRING DIAGRAM; IRCUI

F-1 DIAGRAMS F-1 DEMO ZONE DEMO ZONE WIRING DIAGRAM M19808 40A 40A L E AD CO L OR C ODE : W = W H IT E B = B L AC K G = GR EEN 2 3 0 V I N P U T C IRCUI T NOTES: MATERIAL: WIRE 8 AWG TYPE OR THHN OR THWN OR GAS AND OIL RESISTANT 600 V (UL) B W 230 VOL T I N PUT 50 A M P RE C E P T A C L E 50 A M P R...

Page 19 - NOTES

Page 20 - ÇÃ

WARNING AVISO DE PRECAUCION ATTENTION WARNUNG ATEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BEUSED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES. SE RECOMIENDA LEER Y ENTENDER LAS I...