Life fitness Smith Machine - Manuals

Page 2 - Signature Smith Machine; PROPER USAGE; fied by the manufacturer.; CHECK FOR DAMAGED PARTS; replacement parts supplied by LIFE FITNESS.; MAINTAIN LABELS AND NAMEPLATES:; contact LIFE FITNESS for a replacement.; MAINTAIN ALL EQUIPMENT:; PERSONNEL FOR CLARIFICATION.

Signature Smith Machine Safety & Warranty Purchasers of LIFE FITNESS products should read the Owner's Manual and all of the warning labels on the products before using them. Because theseproducts may be used in commercial settings, it is the purchaser's responsibility to instruct all individuals...

Page 4 - LIMITED WARRANTY; WHAT IS COVERED; 0 years on structural frame; WHAT IS NOT COVERED

Signature Smith Machine Safety & Warranty LIMITED WARRANTY WHAT IS COVERED This Life Fitness commercial exercise equipment (Signature Benches and Racks) is warranted to be free of all defects in material and workmanship to theoriginal purchaser for the specific items and duration listed: O 10 ye...

Page 5 - HOW TO GET PARTS & SERVICE; Write the RA# on the outside of the carton; EXCLUSIVE WARRANTY

HOW TO GET PARTS & SERVICE Simply call Customer Support Services at (800) 351-3737 or (847) 451-0036, Monday through Friday from 8:00 a.m. to 6:00 p.m. Central Standard Time,and tell them your name, address and the serial number of your Product. They will tell you how to get a replacement part, ...

Page 6 - tubing and 5 1/4” x 3 3/4” “D” shaped tubing with 11 gauge wall thickness.; SIGNATURE SMITH MACHINE

Signature Smith Machine Safety & Warranty 1. Frame Construction: Frame is constructed of mechanical quality steel purchased in mill run quantities. Frame is primarily 2 1/2" x 4 1/2" oval shaped tubing and 5 1/4” x 3 3/4” “D” shaped tubing with 11 gauge wall thickness. 2. Frame Finish: T...

Page 7 - Assembly Instructions

Item Qty Description Part Number 1 1 Left Side Frame 82942xx (Ref) 2 1 Right Side Frame 82943xx (Ref) 3 1 Back Brace 82949xx (Ref) 4 10 M10 X 130mm Bolt 3236220 5 22 3/8" Washer 3236601 6 10 1/4" Spacer (.82” OD) 7634701 7 10 M10 Socket Head Nut 7335401 8 6 M10 X 25mm Bolt 3236202 9 10 1"...

Page 8 - With the help of another person, erect the LEFT and RIGHT SIDE

Signature Smith Machine Assembly Instructions BE SURE TO SELECT A LEVEL LOCATION FOR ASSEMBLY. THESIGNATURE SMITH MACHINE MUST REST LEVEL AND IN COMPLETECONTACT WITH THE FLOOR. 1. With the help of another person, erect the LEFT and RIGHT SIDE FRAMES (1 & 2). Position the SIDE FRAMES approximatel...

Page 10 - MUST pass BOTH; of the following criteria:; Counterweight Cable Adjustment

6. Loosen the four set screws on the pre-assembled 1.25" SHAFT COLLARS (C) located at the top of the SIDE FRAMES. 7. With the help of another person and the LIFT BAR ASSEMBLY (D) oriented as shown, position it near the bottom of the GUIDE RODS (E). Lift both GUIDE RODS up through the top of theS...

Page 11 - and remove the PULLEY.

When all of the above criteria have been met, tighten the JAM NUT (18) and continue to complete the installation. 15. Install 1" HOLE PLUGS (9) into all open bolt holes. 16. Cycle the machine to ensure smooth LIFT BAR operation up and down. Counterweight Cable Adjustment If the CABLE is still to...

Page 12 - Maintenance

Signature Smith Machine Maintenance ONCE A WEEK O Visually inspect all hardware, including jam nuts, for loosening, tampering or wear. O Check condition of hand grips. ONCE A MONTH O Inspect hardware and tighten any bolts or nuts that may have loosened during use. O Clean Guide Rods with Break-Free ...