Life fitness OHDMR - Manuals

Page 2 - PARTS LIST; Tools Required for Assembly

PARTS LIST PART # LEA 7586101 LEA 7586501 LEA 7664501 LEA 7584901 LEA 7663601 LEA 7586601 LEA 7663401 LEA 7663901 LEA 7584401 LEA 7584501 LEA 7587501 LEA 7587901 LEA 7587801 LEA 7589201 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 QTY 1 1 2 2 2 2 1 1 1 1 10 1 1 2 KEY 15 16 17 18 19 20 21 22 23 24 25 26 27 P...

Page 4 - FIGURE 1

STEP 1: FIGURE 1 4 • LOOSELY assemble the REAR UPRIGHT (4) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITC DOME WASHERS (22), two 1/2” INT TOOTH LOCK WASHERS (20) and two 1/2” LOCK NUTS (23) as shown in FIGURE 1. 23 4 4 26 1/2 X 4-1/4” 2 20 1 22 • LOOSELY assemble th...

Page 5 - FIGURE 2

5 STEP 2: FIGURE 2 • LOOSELY assemble the BOTTOM UPRIGHT SUPPORT (15) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (26), four 1/2” PLASITC DOME WASHERS (22), four 1/2” INT TOOTH LOCK WASHERS (20) and four1/2” LOCK NUTS (23) as shown inFIGURE 2. 4 26 1/2 X 4-1/4” 22 4 15 20 23 Use this set ...

Page 6 - FIGURE 3

6 STEP 3: FIGURE 3 • LOOSELY assemble the FRONT UPRIGHT (3) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITC DOME WASHERS (22), two 1/2” INT TOOTH LOCK WASHERS (20) and two 1/2” LOCK NUTS (23) as shown in FIGURE 3. 23 3 3 26 1/2 X 4-1/4” 2 20 1 22 • LOOSELY assemble t...

Page 7 - FIGURE 4

7 STEP 4: FIGURE 4 4 5 3 • LOOSELY assemble two LOWER CROSS SUPPORTS (5) to the FRONT UPRIGHTS (3) and the REAR UPRIGHTS (4) using eight 1/2 X 4-1/4” BOLTS (26), eight 1/2” INT TOOTH LOCK WASHERS (20), eight 1/2” PLASITC DOME WASHERS (22) and eight1/2” LOCKNUTS (23) as shown in FIGURE 4. 1/2 X 4-1/4...

Page 8 - FIGURE 5

8 STEP 5: FIGURE 5 • LOOSELY assemble the CHIN-UP SUPPORT (8) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (26), four 1/2” PLASTIC DOME WASHERS (22), four 1/2” INT TOOTH LOCK WASHERS (20) and four 1/2” LOCK NUTS (23) as shown in FIGURE 5. 8 20 22 23 1/2 X 4-1/4” 26 4 4

Page 9 - FIGURE 6

9 STEP 6: FIGURE 6 • LOOSELY assemble the WEIGHT HORN UPRIGHTS (6) to the LEFT & RIGHT UPRIGHT BASE (1 & 2) and REAR UPRIGHTS (4) using eight 1/2 X 4-1/4” BOLTS (26), eight 1/2” PLASTIC DOME WASHERS (22), eight 1/2” INT TOOTH LOCK WASHERS (20)and eight 1/2” LOCK NUTS (23) as shown in FIGURE ...

Page 10 - FIGURE 7; Securely tighten all loose frame connections made to this point.; TIGHTEN

10 STEP 7: FIGURE 7 • Securely tighten all loose frame connections made to this point. TIGHTEN BOTH SIDES! TIGHTEN BOTH SIDES!

Page 11 - FIGURE 8; DETAIL 8

STEP 8: FIGURE 8 • LOOSELY assemble one RIGHT & one LEFT ADJUSTMENT RACK (9 & 10) to the REAR UPRIGHTS (4) as shown, using eight 3/8 X 3-3/4” FLAT HEAD BOLTS (18), eight 3/8” INT TOOTH LOCK WASHERS (21) and eight 3/8” LOCK NUTS (24). See FIG-URE 8. 24 3/8 X 3-3/4” 18 21 9 10 4 4 13 12 • Befo...

Page 12 - FIGURE 9

12 STEP 9: FIGURE 9 • SECURELY assemble the ten WEIGHT HORNS (11) to the WEIGHT HORN UPRIGHTS (6) using twenty 1/2 X 4-1/4” BOLTS (26), twenty 1/2” INT TOOTH LOCK WASHERS (20), twenty 1/2” PLASTIC DOME WASHERS (22) and twenty 1/2” LOCK NUTS (23) asshown in FIGURE 9. 1/2 X 4-1/4” 26 20 11 6 6 22 23

Page 14 - equipment, call your local Hammer Strength distributor .

14 STEP 11: FIGURE 11 • Insert the LEFT BAR SUPPORT (12) into the desired slots of the LEFT ADJUSTMENT RACK (10), and allow it to drop down to lock in place. See FIGURE 11. 10 13 12 • Repeat the above step to assemble the RIGHT BAR SUPPORT (13) to the RIGHT ADJUSTMENT RACK (9). 9 7 Thank you for pur...

Page 15 - PREVENTATIVE MAINTENANCE TIPS; Consult your physician before beginning any exercise program.; WARRANTY INFORMATION

Clean: • Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with touch-up paint can be purchased from your Hammer Strength customer service representative. Inspect: • Cables for wear or damage and proper tension (...