Life fitness GS1 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody GS1 Gym System. Please read these instructions thoroughly and keep them for future reference. * Rubber mallet or hammer* 3/4” wrench* 9/16” wrench* Ratchet with 3/4” and 9/16” sockets* 5/32” Allen wrench...

Page 5 - PARTS LIST

5 PARTS LIST 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 PART # ACU04-1163 ACU04-1158 ACU02-1060 ACU04-1160 ACU04-1384 ACU04-1344 ACU04-1100 ACU04-1098 ACU04-1159 ACU04-1162 ACU04-1157 ACU02-1071 ACU07-0135 ACU01-1782 ACU6194601 ACU01-1783 ACU04-1099 ACU01-2009 ACU10-0204ASY ACU13-0091-2 ACU13-0091-1 ACU7...

Page 6 - FIGURE 1

FIGURE 1 6 STEP 1: 1 3 4 3 0 2 7 3/8 X 3-3/4 2 9 34 3 • LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30) and four 3/8” LOCK NUTS (34). See FIGURE 1. 6 3 4 4 7 3/8 X 4 36 • LOOSELY assemble the FOOTPLATE (7) to the lower holes in the FRAME (1) usin...

Page 8 - FIGURE 4; FIGURE 5

• Insert two GUIDE RODS (16) into the BASE (2) as shown on FIGURE 4. (NOTE: If the GS1 SHROUD OPTION was purchased, place the GUIDE RODS(16) through the BOTTOM SHROUD BRACKET (FOUND IN THE SHROUD KIT BOX ) into the BASE (2), as shown in FIGURE 4. • Using EXTREME CARE slide all fifteen WEIGHT PLATES ...

Page 9 - FIGURE 6

FIGURE 6 8 2 9 3 6 9 3 4 STEP 6: • Place PRESS ARM (8) into PRIMARY PIVOT (9) and insert two 3/8 X 3” BOLTS (29), and two 3/8” FLAT WASHERS (36). While Pushing the PRESS ARM (8) forward, securely tighten the two 3/8 x 3” BOLTS (29) to 20 LBS/FT of torque using two 3/8” FLAT WASHERS (36) and two 3/8”...

Page 10 - FIGURE 7

1 0 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 7: • Assemble the PRIMARY PIVOT (9) of the PRESS ARM ASSEMBLY to the top of the FRAME (1) using 1/2 X 8-3/4” BOLT (33), two 1/2” FLAT WASHERS (37) and 1/2” LOCK NUT (58). • SECURELY TIGHTEN ALL FRAME CONNECTION BEFORE PROCEEDING TO NEXT STEP 3 3 3 7 5 8...

Page 11 - FIGURE 8

11 STEP 8: • Securely tighten the SPRING PIN (50) to the FRAME (1) and hand tighten the STAR KNOB (52) • Securely assemble one SEAT PAD (13) to the SEAT ADJUSTMENT (10) using two 3/8 X 3” BOLTS (29) and two 3/8” WASHERS (36) as shown. FIGURE 8 • Securely assemble one SEAT PAD (13) to the FRAME (1) u...

Page 12 - FIGURE 9

FIGURE 9 STEP 9: • Assemble the LEG PEDESTAL (11) to the FRAME (1) using one 1/2 X 104mm BOLT (32), two RH WASHERS (56) and one 1/2” LOW HT LOCK NUT (35) • Assemble two RH CAPS (55) to the 1/2” RH WASHERS (56) as shown in FIGURE 9 • Route LAT CABLE (20) and LOW CABLE (21) as shown in FIGURE 10 3 2 2...

Page 13 - ILLUSTRATION A

ILLUSTRATION A NOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER TO THE CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEGPRESS KIT 1 3 • ILLUSTRATION “A” used as cable routing reference for steps 12-15

Page 21 - SERIAL NUMBER LOCATION

MAINTENANCE MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 2 1 * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be pur...

Page 22 - LIMITED WARRANTY

2 2 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...