Life fitness FSFCM1-0102-001 - Manuals

5 EXPLODED VIEW SERIAL# (inside of cover) SERIAL # SHROUD KIT PLACARD PLACEMENT

6 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 REQUIRED TOOLS: HARDWARE: * 9/16” wrench* Ratchet and 9/16” socket* Adjustable wrench* Tape measure* Two 5/16” Allen wrenches* 4 mm Allen wrench* 3/4 Wrench* Phillups Screw Driver BOLT LENGTH

7 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 1 STEP 1: ‰ LOOSELY assemble bottom of the LEFT UPRIGHT (4) and RIGHT UPRIGHT (5) to FRONT UPRIGHT (1)using four 3/8 x 3-1/2 BOLTS (34), eight 3/8 WASHERS (28) and four 3/8 NUTS (33) and TOP PULLEYS (7) ‰ LOOSELY assemble the top of the LEFT UPRIGHT (4)...

STEP 2: ‰ LOOSELY attach BASE PLATFORM (2) to front of FRONT UPRIGHT (1) using two 3/8 x 3/4” BOLTS (31), and two 3/8 WASHERS (28). ‰ LOOSELY attach the BASE PLATFORM (2) to the sides of UPRIGHTS (4) and (5) using two 3/8 x 3-1/2 BOLTS (34) and two 3/8 WASHERS (28) ‰ Assemble TOP BACK COVER (16) to ...

STEP 3: ‰ Insert two GUIDE ROD BUSHINGS (30) into bottom of FRONT UPRIGHT (1), slide one CUSHION (24) to bottom of eachGUIDE ROD (22) and insert both GUIDE RODS (22) thru GUIDE ROD BUSHINGS (30) and holes located at bottom ofFRONT UPRIGHT (1) ‰ CAREFULLY slide HEAD PLATE (12) over top of GUIDE RODS ...

MUST DISASSEMBLE ONE END OF CABLE AND REASSEMBLE AFTER ROUTING (SEE FIG 7 PAGE 14) STEP 4 ‰ NOTE: IF THE 50# ADD ON KIT WAS PURCHASED, USE THE CABLE FROM THAT KIT AND REFER TOKIT ASSEMBLY INSTRUCTION FOR HEAD PLATE ASSEMBLY ‰ Dimension between bottom of PULLEY BRACKET and top of JAM NUT approximatel...

STEP 5: ‰ Insert ball end of GUIDE CABLE 7746001 (42) through eye hook on FLOATING PULLEY BRACKET (11), insert and hookball end of cable into slotted bushing located at the bottom of frame. ‰ Screw threaded end of cable into the FRONT UPRIGHT (1) and loosely tighten cable by screwing JAM NUT to top ...

MU ST DISASSEMBLE ONE END OF CABLE AND REASSEMBLY AFTER ROUTING (SEE FIG 7 PAGE 14) STEP 6: ‰ Insert ball end of LONG CABLE 7745401 (44) under pulley #1 and thru slot in BASE PLATFORM (2).Run cable underneath and up the back side of pulley #2. Then run cable up and around the front and downthe back ...

STEP 7: ‰ USE THIS ASSEM B LY AT THE END OF EACH CABLE ‰ Slide each item onto cable as follows: ITEM 1, ITEM 2, ITEM 3, and insert cable end into ITEM 4. ‰ Slide entire assembly over ITEM 4 and secure by screwing ITEM 5 into ITEM 4 and TIGTHEN SECUR E LY 14 FIGURE 7 ITEM QTY. PART NO. DESCRIPTION 1 ...

STEP 8 ‰ Attach FRONT SHROUD (8) using two 3/8 X 2-1/2 SCREWS (35) and two 3/8 WASHERS (28) ‰ Attach REAR BOTTOM PLATE (13) using two 10-32 X 1/2 SCREWS (25) ‰ SECURELY TIGTHEN CABLE GUIDES (REFER TO FIG 5, PAGE 11) 15 FIGURE 8 3/8 x 2-1/2 10-32 x 3/8

MAINTENANCE 19 * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Life Fitness customer service representative at (800) 328-9714.(Outside of the U.S. and Canada, +1-847-288-3300) * Inspect equipment daily. Tight...

Clean: • Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at (800) 351-3737 Inspect: • Cables for wear or damage and pro...

21 LIMITED WARRANTY Life Fitness® FIT 1.0 CM Life Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchase required, keep yourreceipt with this manual) of the Life Fitness product. The Warranty terms apply to IN HOME and LIGHT INSTITUTIONALUSE ONLY. 1. LIMITED WARRANTY...