Life fitness CSLAT - Manuals

Page 3 - FIGURE 1

STEP 1: FIGURE 1 4 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble the TOWER (1) to the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/4” BOLTS (10), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 1. 1 10 3/8 X 3-3/4” 11 3 2 7 1 4 1B

Page 5 - FIGURE 2

5 FIGURE 2 STEP 2: • LOOSELY assemble the MAIN UPRIGHT (2) to the base of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/ 4” BOLTS (10), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 2. 3/8 X 3-3/4” 10 9 3/8 X 2-3/4 2 7 1 4 1 3 2 11 3 • LOOSELY assem...

Page 6 - FIGURE 3

6 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 3 STEP 3: • SECURELY assemble the KNEE SUPPORT (5) to the BENCH FRAME (3) using two BLACK RH CAPS (17), two RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHTLOCK NUTS (11) as shown in...

Page 7 - FIGURE 4

7 STEP 4 FIGURE 4 • SECURELY assemble the SEAT PAD (18) to the BENCH FRAME (3) using two RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9) and two 3/8” RH WASHERS (14) as shown in FIGURE 4. 3/8 X 2-3/4” 9 1 4 2 7 3 1 8 5A

Page 8 - FIGURE 5; HEAVY WEIGHT

8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 5: FIGURE 5 • Insert the two GUIDE RODS (26) (found in the SHROUD KIT) into the base of the TOWER (1) as shown in FIGURE 5. Lubricate the GUIDE RODS (26) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUS...

Page 9 - FIGURE 6

9 • Screw the treaded end of the CABLE all way into the end of the shaft on the HEAD PLATE (8) and tighten jam nut securely. See FIGURE 6. STEP 6: FIGURE 6 • SECURELY assemble the GUIDE ROD SUPPORT (6) to the TOWER (1) and MAIN UPRIGHT (2) using four RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9), four 3/...

Page 10 - FIGURE 7

0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 1 0 S T ` ` ` ` ` FIGURE 7 • Peel the backing off the WEIGHT STACK LABELS (12), line up sheet to the right of the selector opening and apply labels to the WEIGHT PLATES (24), starting with the HEAD PLATE (8) as shown in FIGURE 7. 1 2 8 2 4 TIGHTEN! • The WEIGHT ...

Page 11 - FIGURE 8

11 FIGURE 8 • Assemble the PLACARD LABEL (22) or the FOREIGN LANGUAGE PLACARD LABEL (23) to the FRONT SHROUD as shown in FIGURE 8. STEP 8: 2 3 2 2 7 2 1 4 • Attach LAT BAR (4) and/or TRICEP ROPE (7) end of cable using on SNAP LINK (21) with the TRICEP ROPE (7) as shown in FIGURE 8. 29 31 32 4A

Page 13 - FIGURE 9

12 STEP 9: FIGURE 9 • SECURELY assemble the FRONT FULL SHROUD (31) and the REAR FULL SHROUD (32) to the TOWER (1) using ten 3/8 X 3-1/2” BUTTON HEAD BOLTS (28), ten STARLOCK WASHERS (27), and ten 3/8” ACORN NUTS (12) as shown in FIGURE9 . 3/8 X 3-1/2” 28 2 7 3 1 3 2 1 1 2 0 1 2 3 4 5 6 1/2 1/2 1/2 1...

Page 14 - PREVENTATIVE MAINTENANCE TIPS; Consult your physician before beginning any exercise program.; CLEAN; WARRANTY INFORMATION

Clean: • Upholstery with mild soap and water.• Guide rods with a cotton cloth.• Hand grips with mild soap and water.• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at (800)328-9714. Inspect: • Cables for wear or damage and pro...