Life fitness 8973601 - Manuals

3 A SSEMBLY 3.1 T OOLS & H ARDWARE Identify the following components after unpacking your cross-trainer: 8 WAVE WASHER (QTY.2) FLAT WASHER 10mm ID (QTY. 2) LARGE FLAT WASHER (QTY. 2) M10 X 74MM BLACK HEX HEAD BOLT (QTY. 2) M10 X 20MM CLEAR ZINC HEX HEAD BOLT (QTY. 3) M10 X 15MM SILVER HEX HEAD B...

10 3.6 A SSEMBLE THE R OCKER A RMS Parts: Hardware Bag #3 (2, Wave Washers, 2 Large Flat Washers) (2, Flat Washers)(2, M10 X 20mm Hex Head Bolts)(2, Plastic End Caps) Tools: 17mm Socket Wrench, Phillips Screwdriver, Rubber Mallet Slide one large Flat Washer (I) and one Wave Washer (J) onto the user ...

3.7 A SSEMBLE M OVING A RMS TO P EDAL A RMS Parts: Hardware Bag #4 (2, M10 X 74mm Black Hex Head Bolts)(2, M10 Hex Nuts) Tools: 17mm Socket Wrench, Phillips Screwdriver Lift the front end of the user left pedal lever (Q) to meet the left rocker arm clevis (R). Secure the pedal lever to the rock-er a...

13 3.9 C ONNECT ALL C ONSOLE W IRING ; C ONSOLE TO C ONSOLE B RACKET ; B ACK P LASTIC S HELL Parts: Hardware Bag #6 (4, M5 X 12mm Silver Phillips Screws) Tools: Phillips Screwdriver Position the console (Z) close to the console bracket (W) and followthe below instructions to connect all wiring. Plug...

14 4 I NITIAL S ETUP Read the entire User Manual before setting up the Total-Body Elliptical Cross-Trainer. Note: This Total Body Elliptical Cross-Trainer is speed independent. Resistance can be adjusted by means other than speed. W HERE TO P LACE THE T OTAL -B ODY E LLIPTICAL C ROSS -T RAINER After...

C ONTACT H EART R ATE The X1 includes hand pulse sensors on the stationary handlebar that are a built-in heart rate monitoring system. During aworkout grasp the hand pulse sensors to monitor your heart rate. We recommend using the heart rate chest strap providedwith your console during workouts and ...

16 5 S ERVICE & P RODUCT M AINTENANCE 5.1 T ROUBLESHOOTING Problem Cause / Solution No power. Check to see that the power cord is fully plugged into the back of theTotal-Body Elliptical Cross-Trainer and into the wall. Make sure the powercord is fully seated into the back of the Total-Body Ellip...

17 Problem Cause / Solution Creaking sound is coming from thestabilizers. It is very important that the nut on the leveler is tightened against the stabilizer tube after the product is leveled. Ensure that this nut is tight. “OFF” is displayed in the LEVEL window on the console. Turn the unit off an...

19 6 S PECIFICATIONS L IFE F ITNESS X1 C ROSS -T RAINER S PECIFICATIONS Designed Use: Home Max User Weight: 350 lbs / 159 kilograms Max Step-Up Height: 6.5 inches / 16.5 centimeters Resistance System: Eddy Current Stride Length: 20 inches Power Supply: 120 Volt (U.S.), 220 Volt (Europe), 240+ Volt (...

7 W ARRANTY I NFORMATION WHAT IS COVERED: This Life Fitness consumer product ("Product") is warranted to be free of all defects in material and workmanship. WHO IS COVERED: The original purchaser or any person receiving a newly purchased Product as a gift from the original purchaser.Warranty...

21 HOW TO GET PARTS & SERVICE: Refer to page one of this manual for your local service contact information. Reference your name, address and the serialnumber of your Product (consoles and frames may have separate serial numbers). They will tell you how to get areplacement part, or, if necessary,...