Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...
Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler
IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 843 Rack System. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. 3 NOTE: BOLT LENGTH I...
Page 5 - PARTS LIST; FIGURE 1
5 PARTS LIST PART # LEA6641509 LEA6641810 LEA6605710 LEA6605810 LEA6605910 LEA6606010 LEA6658610 LEA3235312 KEY 1 2 3 4 5 6 7 8 QTY 2 2 2 2 1 1 1 12 PART # LEA3235316 LEA3114401 LEA3114701 LEA6606801 LEA6405201 LEA7234801 LEA6590801 D E S C R I P T I O N 1/2 X 4” BOLT 1/2” WASHER 1/2” LOCK NUT SPRIN...
Page 6 - FIGURE 2
6 FIGURE 2 STEP 2: • SECURELY assemble the six SPRING PIN ASSEMBLIES (12) to the SPRING PIN BARRELS on each SAFETY RAIL (3) and each BAR SUPPORT (4) as shown in FIGURE 2. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Insert twelve 3 X 2” INSERT GUIDES (15) into the ends of each SAFETY RAIL (3) and BAR SUP...
Page 7 - FIGURE 3
7 FIGURE 3 STEP 3 • Slide one BAR SUPPORT (4) and one SAFETY RAIL (3) (IN THAT ORDER) onto each UPRIGHT (1). Pull back on the SPRING PIN ASSEMBLIES until they pop into holes. • Insert four 2” SQ. END CAPS (13) into the ends of the UPRIGHTS (1) as shown in FIGURE 3. 3 4 1 13
Page 8 - FIGURE 4
8 STEP 4: FIGURE 4 • LOOSELY assemble each UPRIGHT (1) to the UPRIGHT BASE (2) using four 1/2 X 4” BOLTS (9), eight 1/2” WASHERS (10), and four 1/2” LOCK NUTS (11). See FIGURE 4. • LOOSELY assemble the UPPER CONNECTOR (7) using four 1/2 X 3” BOLTS (8), four 1/2” WASHERS (10), and two 1/2” LOCK NUTS ...
Page 9 - FIGURE 5; THIS CONCLUDES THE ASSEMBLY OF THE 843 RACK SYSTEM.
9 STEP 5: FIGURE 5 • LOOSELY assemble the CHIN BAR (5) using four 1/2 X 3” BOLTS (8), four 1/2” WASHERS (10), and four 1/2” LOCK NUTS (11). See FIGURE 5. When all components are assembled, SECURELY tighten all bolt connections. 11 10 5 1/2 X 3” 8 THIS CONCLUDES THE ASSEMBLY OF THE 843 RACK SYSTEM.
Page 11 - LIMITED WARRANTY
11 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired o...