Life fitness 8215 - Manuals

Page 2 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH; Consult your physician before beginning any exercise program.

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8215 MULTI-PRESS. Please read these instruc- tions thoroughly and keep them for future reference. This product must be assembled on a flat,level surface to assure its proper function. 2 NOTE: BOLT LE...

Page 3 - PARTS LIST

3 PARTS LIST PART # 6795203 6784303 6755602 6755903 6878202 6783403 6781303 6784703 6784103 6624302 6624203 6651602 6780304 6780004 6791102 6214501 6284501 6714601 3116101 6782301 6784601 6382301 3108002 3109602 3118401 6757701 3203501 3103302 3202105 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18...

Page 4 - FIGURE 1

4 STEP 1: FIGURE 1 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble LOWER SUPPORT (6) to the TOWER (1) and PRESS FRAME (2) using four 1/2 X 4” BOLTS (31), four 1/2” WASHERS (41), and three 1/2” LOCK NUTS (43). See FIGURE 1. • LOOSELY assemble UPPER SUPPORT (8) to the TOWER (1) and PRESS FRAM...

Page 5 - FIGURE 2

STEP 2: FIGURE 2 5 • SECURELY assemble one 3/8” SPRING PIN (48) to the WOLFF SLEEVE (3) as shown in FIGURE 2. (IMPORTANT! Tighten nut of SPRING PIN completely.) • Attach one U-PIN (50) to the WOLFF SLEEVE (3) using one 1/2” PAL NUT (24). Slide one 4” VINYL CAP (25) onto the U-PIN (50) as shown in FI...

Page 6 - FIGURE 3

STEP 3: FIGURE 3 6 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the PRESS FRAME (9) to the PRESS BASE (2) using one 1/2 X 3” BOLT (32), two 1/2” WASHERS (41), and one 1/2” LOCK NUT (43), as well as two 3/8 X 3” FLAT HEAD BOLTS (36), one 1/4 X 8” PLATE (56), two 3/8” WASHERS (42), andtwo...

Page 7 - FIGURE 4

7 STEP 4: FIGURE 4 • Slide two HINGE TABS (46) onto the WOLFF SLEEVE (3) and SECURELY assemble SEAT PAD (14) using two 3/8 X 1-1/4” BOLTS (39), and two 3/8” WASHERS (42). See FIGURE 4. (NOTE: Please note the HINGE TAB direction.) 39 3/8 X 1-1/4” 3 46 14 42

Page 8 - FIGURE 5

STEP 5: 8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Slide the RIGHT BACK PAD ANGLE (10) and the LEFT BACK PAD ANGLE (11) onto the shaft on the WOLFF SLEEVE (3) as shown in FIGURE 5. • Assemble the 1/2 X 2 X 15-1/2” PLATES (12) to the RIGHT BACK PAD ANGLE (10) and the LEFT BACK PAD ANGLE (11) using two...

Page 9 - FIGURE 6

FIGURE 6 9 • SECURELY assemble the BACK PAD (13) to the LEFT & RIGHT BACK PAD ANGLES (11 & 10) using four 3/8 X 1-1/4” BOLTS (39) and four 3/8” WASHERS (42). See FIGURE 6. STEP 6: 39 3/8 X 1-1/4” 13 10 42 11

Page 10 - FIGURE 7

FIGURE 7 10 • Slide two PILLOW BLOCKS (27) over the shaft on the PRESS ARM ADJUST (5) and SECURELY assemble the two PILLOW BLOCKS (27) to the UPPER SUPPORT (8) using four 3/8 X 3-1/4” BOLTS (35), four 3/8” WASHERS (42), and four 3/8” LOCKNUTS (45) as shown in FIGURE 7. STEP 7: 0 1 2 3 4 5 6 1/2 1/2 ...

Page 11 - FIGURE 8

FIGURE 8 11 • SECURELY assemble one 1/2” SPRING PIN (47) to the PRESS ARM (4) as shown in FIGURE 8. (IMPORTANT! Tighten spring pin completely.) STEP 8: 29 1/2 X 7-1/2” 4 5 44 1/2” LOW HEIGHT 47 • SECURELY assemble the PRESS ARM (4) to the PRESS ARM ADJUST (5) using one 1/2 X 7-1/2” BOLT (29), two 1/...

Page 12 - FIGURE 9

12 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 9 STEP 9: • Snap two WEIGHT PLATE BUSHINGS (22) into the top side of all twenty WEIGHT PLATES (16) as shown in FIGURE 9. 22 16