Liebherr RI 1410/ RBI 1410/ FI 1051 - Manuals

4 Cabinet Opening Dimensions Fig. 6 Single installation Fig. 7 Side-by-side installation: The door must be able to be opened at least 90° to allow the drawers to be pulled out properly. If the door opening angle is 90° it may be difficult to remove the drawers due to the door racks.If the appliance ...

Fig. 8 - An effective ventilation cross-section of at least 31 in 2 (200 cm 2 ) per unit must be present at the air intake Fig. 8 (1) and air outlet Fig. 8 (2) . - The upper ventilation cross-section can be set up directly above the appliance with an optional ventilation grille Fig. 8 (2) , near the...

7 Fitting décor panels NOTICE Risk of fire and damage if insufficient ventilation! u If you are replacing the factory air vents with an overlay, Do NOT restrict the air flow. The air flow must be the same or greater than the factory air vents of 31 in 2 (200 cm 2 ). The door panel weight must not ex...

7.2 Décor panel dimensions - Framed panels Fig. 15 Fig. 16 If the thickness of the custom panels is less than 1/4 in. (6.4 mm): u back the panels up with a sheet of shim material to build the total thickness to 1/4 in. (6.4 mm). Fig. 17 If the thickness of the custom panels is thicker than1/4 in. (6...

7.3 Cut-out for glass window (WFI 1061) Fig. 23 (1) Overlay panel (3) Backer panel (2) Spacer panel (4) Glassed area The edges of the panels Fig. 23 (1,2,3) are visible at the transition to the glass window Fig. 23 (4) . It can be covered with a decorative molding Fig. 24 (A) for esthetic reasons. F...

Fig. 31 u Close the door. u Pull cover Fig. 31 (10) forward and then upwards to remove. u Lift off cover Fig. 31 (11) . CAUTION Risk of injury if the door tips out! u Keep a steady grip on the door. u Set the door down carefully. u Unscrew upper bearing bracket Fig. 31 (12) (2 x Torx 25) Fig. 31 (13...

8.7 Fitting the soft stop mechanism (bottom) Fig. 34 u Loosen cover Fig. 34 (57) from the panel Fig. 34 (51) and insert on the other side. u With the hinge of the soft stop unit facing the door hinge side, engage the soft stop unit (A) and swivel inwards (B). w The holes on the left and right must l...

u Remove locking device Fig. 37 (2) by twisting it. u Snap panel Fig. 37 (1) into place on the door. u Turn cover Fig. 27 (6) 180° from the handle side, place it on top from the outside and snap into place. 8.9 Aligning the door u Unscrew center screw on lower part of bearing bracket Fig. 32 (20) . ...

Fig. 41 u With the hinge of the upper soft stop unit facing the door hinge side, engage the soft stop unit (A) and swivel inwards (B). w The holes on the left and right must lie exactly above each other. u Tighten soft stop unit (2 x Torx 15) Fig. 41 (7) . Note u Follow the correct sequence. First h...

NOTICE Risk of thread damage! u Do not overtighten. u Connect the domestic water supply Fig. 43 (5) (e.g. copper pipe) to the elbow connector Fig. 43 (4) . Before fitting into the cabinet: u Check the whole water system for leaks. Before using for the first time: u Have the water line bled (remove a...

Fig. 48 u Fit retaining plate Fig. 48 (1) to the lower part of the handle side by inserting two screws Fig. 48 (2) into the pre-cut holes. u Slide installation strip Fig. 48 (3) into the retaining plate Fig. 48 (1) from above. u Push second retaining plate Fig. 48 (4) onto the installation strip Fig...

14 Installing the water filter* The water filter guarantees optimal water quality and should be installed the first time you use the appliance.Alternatively, the appliance can also be operated without the water filter. Flow rate 0.5 gpm (1.89 lpm) Water connection Drinking waterWater pressure 40 psi...

WARNING Electrical shock hazard! This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards. Electrical Grounding Required. u Do not remove the round grounding prong from the plug. u Do not use a two-prong grounding adapter. - Wait 1 h...