Liebherr HC 20 - Manuals

Cabinet Opening Dimensions - Figure 4 A = 36" (914 mm) Figure 4 IMPORTANT Do not install the shut-off valve behind the appliance. IMPORTANT The free length of the water supply line must be at least 31 - 1/2" (800 mm) when the tube comes out of the prescribed opening. IMPORTANT At 24" cab...

IMPORTANT Please note the cabinet depth of 24-3/4" (629 mm) only at framed cabinet design. Framed Cabinet - Figure 5 At Framed Cabinets the panel front is in line with the Cabinet frame. Cabinet frame. Figure 5 6 P LANNING I NFORMATION

Panel Dimensions - Framed Cabinet Design - Figure 6 Figure 6 The panels should be at least 5/8 inch (16 mm) thick to allow the connecting rails to be fastened to them. IMPORTANT The maximum panel thickness is 3/4" (19 mm). Cabinet Opening A Refrigerator door panel B 80" (2032 mm) 45 - 9/32&#...

At Frameless Cabinets the panels are in front of the Cabinet frame. Frameless Cabinet - Figure 7 Figure 7 8 P LANNING I NFORMATION

Panel Dimensions - Frameless Cabinet Design - Figure 8 The gap between all panels at frameless cabinet design is 1/4" (6 mm). The panels should be at least 5/8 inch (16 mm) thick to allow the connecting rails to be fastened to them. Figure 8 IMPORTANT The maximum panel thickness is 3/4" (19 ...

Figure 8 Mounting the anti tipping device on concrete floors - Figure 9 - 10 Secure the appliance in place so it does not tip for- ward when the fully stocked doors are opened. The anti tipping bracket is provided with the appliance. 1. Mark the center line of the appliance on the back wall. Align t...

Figure 11 Mounting the anti tipping device in cabinets deeper than 24" - Figure 12 - 13 1. Mark the center line of the appliance on the back wall. Align the anti tipping bracket center to this line. Be sure that there is no plumbing or electrical wiring located in this area which screws or drill...

Figure 15 12 I CE M AKER IceMaker The icemaker for a combined refrigerator-freezer is located in the freezer compartment. It must be connected to the water supply to function properly. These instructions only refer to the installation of the icemaker. Please refer to the Use and Care Manual provided...

Figure 16 Figure 18 Figure 17 Anti - tipping bracket Compressor mounting plate Wall Appliance 13 Connection to the Water Supply 1. Install the shut-off valve, water filter and auto- matic shut-off device as required. 2. The solenoid valve has a Metric R3/4 male con- nector. A R3/4 (metric) to a 1/4&...

Fasten the appliance in the recess - Figure 20 Fasten the appliance in the recess through the upper and lower hinges of the refrigerator doors. Use 2 screws for each hinge (Figure 20) . Leveling the appliance - Figure 19 1. The height can be adjusted in front by twisting the leveling feet 1 . 2. Twi...

Mounting the attachment brackets onto the door panels - Figure 22 Fasten the dismounted brackets of the refrigerator doors onto the refrigerator door panels using four screws (4 x 16 mm) for each bracket. Fasten the brackets provided onto the freezer drawer panels using three screws (4 x 16 mm) for ...

Mounting the freezer drawer panels - Figure 23 The panels can be attached to the appliance now. The upper drawer panel must be mounted first. 1. Pull out the upper freezer drawer and screw on the panel with three screws at left and right hand side using the screws as shown in Figure 23 . 2. Close th...

5. Close the door and check the height of the panel. 6. Align the panel in its vertical position if necessary. Loosen the hex nuts and turn the adusting bolts using a screwdriver for slotted screws (Figure 26) . 7. Check the vertical position of the panel again and fasten the hex nuts finally. Figur...

Mounting the ventilation grille - Figure 32, 33 1. Pull out the bottom freezer drawer. 2. Remove the blue protection film from the dust filter provided and insert the filter into its opening in the toe kick area as shown in Figure 32 . Figure 31 11. Extend the soft-stop cylinder and connect with the...