LG L222WT-BF - Manuals

LG L222WT-BF Monitor – User Manual in PDF format online.

Manuals:

User Manual

User Manual LG L222WT-BF

Summary

Page 2 - On Safety; Do not Open the Display.; Important Precautions

A1 This unit has been engineered and manufactured to ensure your personalsafety, however improper use may result in potential electrical shock or firehazards. In order to allow the proper operation of all safeguardsincorporated in this display, observe the following basic rules for itsinstallation, ...

Page 3 - On Installation; screen because over-spraying may cause electrical shock.; On Repacking

A2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a ...

Page 4 - Connecting the Display; Important; Connecting the stand; Place the monitor with its front facing downward on a soft cloth.

A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot. Before setting up the m...

Page 5 - Pushing Latch inside, Take the stand base from stand body.

A4 Connecting the Display Disassembling the standType. A 1. Put a cushion or soft cloth on aflatsurface. 3. Pushing Latch inside, Take the stand base from stand body. 5. Pack up the product as shown in the picture. 4. Separate the stand using a screwdriver as shown in the picture. Note: Please keep ...

Page 6 - Pull out the Stand to remove.

A5 Connecting the Display Disassembling the standType. B 1. Put a cushion or soft cloth on aflatsurface. 3. Change your hold on the product as it follows and turn the Stand Base in the arrow direction. 5. Pushing Latch inside, Take the standbase from stand body. 6. Pack up the product as shown in th...

Page 7 - Positioning your display; Ergonomic

A6 Connecting the Display 20 Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Ergonomic It is recom...

Page 8 - Using the Computer; to; NOTE; Connect DVI Cable

A7 Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch mapform to . 1 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) N...

Page 9 - Control Panel Functions; ZOOMING; Recommend resolution are 1680; Control; MENU Button; Use this button to enter or exit the On Screen Display.; The message; MENU button; for several seconds. The message; Front Panel Controls

A8 Control Panel Functions ZOOMING At the current display, Use 'ez Zooming' Key, then the displayresolution is transferred to the one step low resolution.Use 'ez Zooming' Key one more, the display is back to theoriginal display. *Only One touch of ez-zoom, you can fine the best resolutionyou want an...

Page 10 - Use this button to turn the display on or off.; Power Button; button before entering the On Screen; Power Indicator; Buttons

A9 Control Panel Functions This Indicator lights up blue when the displayoperates normally(On Mode). If the display is in SleepMode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off. Power Button Use this button to enter a selection in the On Scree...

Page 11 - On Screen Display (OSD) Control Adjustment; Screen Adjustment

A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters ofthe display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.The follo...

Page 12 - On Screen Display(OSD) Selection and Adjustment; PICTURE; POSITION VERTICAL; FLATRON

A11 NOTE The order of icons may differ depending on the model (A11~A16 ). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus. To adjust the brightness,contrast and gamma of thescreen PICTURE COLOR POSITION TRA...

Page 13 - Press the MENU Button, then the main menu of the OSD appears.; P I C T U R E

A12 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the ...

Page 14 - Main menu

A13 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues d...

Page 15 - To move image left and right.; POSITION; To adjust the clearness of the screen.; TRACKING

A14 MENU : Exit : Decrease : Increase SET : Select another sub-menu On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description HORIZONTAL VERTICAL To move image left and right. To move image up and down. POSITION P O S I T I O N - + MENU : Exit : Decrease : Increase SET : Select ...

Page 16 - SETUP

A15 Press the button to reset immediately. On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled only whenth...

Page 18 - Troubleshooting; Check the following before calling for service.; No image appears

A17 Troubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue orgreen? ● Is...

Page 19 - Display image is incorrect

A18 Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, verticalbars or stripes arevisible. ● Any horizontal noise appearing in anyimage or charactersare not clearlyportrayed. • Press the AUTO/SET button to automatically adjust your display image t...

Page 20 - Have you installed the display driver?; Have you installed the; The screen color is

A19 Troubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor,Plug&Play (VESA DDC)monitor found"message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with yourdispla...

Page 21 - Specifications; Information in this document is subject to change without notice.

A20 Specifications NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play PowerConsumption Dimensions &Weight Tilt Range Power Input Environmental Conditions Stand Base Signal cable Power cord 21.6 inches (54.864 cm) Flat Pa...

Page 22 - Indicator; LED Color

A21 Specifications Preset Modes (Resolution) *Recommend Mode Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 123456789 1011 *12 720 x 400640 x 480640 x 480800 x 600800 x 600 1024 x 7681024 x 7681152 x 864 1280 x 10241280 x 10241680 x 10501680 x 1050 31.46831.46937.50037.87946.8...

Page 23 - Installing the Wall mount plate; Kensington Security Slot

A22 Installing the Wall mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plate ispurchased. Kensington Security Slot Connected to a l...

Page 24 - Digitally yours