LevelOne 8+8 POE 10/100 Mbps Web Smart Switch - Manuals

3 INTRODUCTION This chapter describes the features of the FSW-1670TX 8+8POE 10/100Mbps Web Smart Switch and some background information about Ethernet/Fast Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applic...

4 Switching Technology Another approach to pushing beyond the limits of Ethernet technology is the development of switching technology. A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments. Switching i...

6 separate electrical wiring and power outlets. Features 16×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 8- port PoE function (port-1 ~ port-8) Compliant with IEEE 802.3af specification Supports PoE power maximum 15.4W for each PoE ports Supports PoE Powered Device (PD) classification i...

7 UNPACKING AND INSTALLATION This chapter provides unpacking and installation information for the Switch. Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: FSW-1670TX 8+8POE 10/100Mbps Web Smart Switch One AC power co...

Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack installation, see the next section, Rack Mounting . When installing the Switch on a level surface, attach the rubber feet to the bottom of each device. The ru...

IDENTIFYING EXTERNAL COMPONENTS This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel The figure below shows the front panel of the Switch. Figure 3. Front panel of the Switch LED Indicator: Comprehensive LED indicators display the status of the switch and...

Card) or switch and hub. Ethernet Ports (Port 9~16): These ports support network speeds of either 10Mbps or 100Mbps, and can operate in half- and full- duplex transfer modes. These ports also supports automatic MDI/MDIX crossover detection function gives true “plug and play” capability, just need to...

UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. Figure 5. LED indicators of the Switch Power and System LEDs POWER: Power Indicator On : When the Power LED lights on, the Switch is receiving power. Off : When the Po...

14 100Mbps On : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. Off : When the respective port is connected to a 10Mbps Ethernet network PoE Status Green : When the PoE device was connected and the port supplies power successfully. Red : When the ...

15 CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN, Trunking, and QoS… etc. With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware. Installing the Web...

Figure 6. Web Management Utility The Web Management Utility was divided into four parts, Discovery List, Monitor List, Device Setting and Toolbar function , for details instruction, follow the below section. Discovery List This is the list where you can discover all the Web management devices in the...

Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you want to monitor. Delete Item: To delete the device in the Monitor List. Device Setting You can set the device by using the function key in the Device Setting Dialog box. Configuration Setting: In this...

Figure 10. Password Change Firmware Upgrade: When the device has a new function, there will be a new firmware to update the device, use this function to update. Figure 11. Web Access: Double click the device in the Monitor List or select a device in the Monitor List and press this “Web Access” butto...

21 Monitor Save: To record the setting of the Monitor List to the default, when you open the Web Management Utility next time, it will auto load the default recorded setting. Monitor Save As: To record the setting of the Monitor List in appointed filename and file path. Monitor Load: To manually loa...

Setup Menu When the main page appears, find the Setup menu in the left side of the screen (Figure 15). Click on the setup item that you want to configure. There are eleven options: Port Settings, VLAN Settings, Trunk Settings, Mirror Settings, QoS Settings, PoE Settings, Device Status, Statistic, Sy...

Port Settings In Port Settings menu (Figure 16), this page will show each port’s status, press the ID parameter to set each port’s Speed, Flow Control, Rate Control Ingress and Egress . When you need to renew the posted information, press the “Refresh” button. The Link Status in the screen will show...

26 Speed/Disable: This setting has six modes— 100M Full , 100M Half , 10M Full , 10M Half, Auto and Disable —for speed or port disable selections. Flow Control: This setting determines whether or not the Switch will be handling flow control. Set FlowCtrl to Enable for avoiding data transfer overflow...

VID: select the VID group that you set. When you select VID Table Setting, press “Add new VID” to create new VID group, from port 01 ~ port 16, select Untag Port, Tag Port or Not Member for each port. To save the VID group, press “Apply” button. To remove the selected VID group, select the VID group...

Trunk Setting The Trunk function enables to cascade two devices with a double times bandwidth (up to 1600Mbps in full duplex mode). There are 4 selection for the trunk setting, port “09,10”, port “09,10,11,12”, port “09,10,11,12,13,14,15,16” or select “disable” for closing this function. Figure 20. ...

RX (receive) mode: this mode will duplicate the data that send to the source and forward to the sniffer port. Both (transmit and receive) mode: this mode will duplicate both the data transmit from and data that send to the source port, then it will forward to the sniffer port. Figure 21. QoS Setting...

Port Based: to set the Switch QoS by port based, select the ports which need to higher the quality by changing Normal to High. Figure 24. IEEE 802.1p Based: to set the Switch QoS base on IEEE 802.1p, Figure 25. PoE Setting When click on the PoE Setting, the status of the PoE will present on the scre...

Figure 26. Press “Refresh” button to refresh the status of the PoE. Press click on the ID parameter to enter to the selected port to configure the PoE settings, select enable to activate the PoE function from port 1 to port 8, and disable to deactivate the PoE function. Click “Apply” button to save ...

Statistic The Statistic Menu screen will show the status of each port packet count. Figure 28. Statistic For Detail packet information, click on the ID parameter as Figure 29. Figure 29. 32

System Setting The System Setting includes the Web Server Port, System name, Location name, Login Timeout, IP Address, Subnet Mask and Gateway. Through the Web Management Utility, you can easily recognize the device by using the System Name and the Location Name. The Login Timeout is to set the idle...

Backup Setting The backup tools help you to backup the current setting of the Switch. Once you need to backup the setting, press the “Backup” button to save the setting. To restore a current setting file to the device, you must specify the backup file and press “Restore” button to proceed the settin...

Logout When press this function, the web configuration will go back to first Login page. Figure 35. Logout 37

39 TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af compliant Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half duplex), 2...