LevelOne 4+4 PoE Fast Ethernet Switch - Manuals

Page 2 - Safety; FCC Warning; ii

Safety FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial enviro...

Page 3 - Table of Content; LED; iii

Table of Content INTRODUCTION .............................................. 1 FEATURES....................................................... 2 PACKAGE CONTENT ..................................... 3 HARDWARE DESCRIPTION ........................... 4 F RONT P ANEL .....................................

Page 5 - Introduction

Introduction The FSW-0809 Switch integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. And this switch’s Port-1 to Port-4 are Power over Ethernet (PoE) ports, and it will automatically detects the presence of IEEE 802.3af-compliant powered device (PD...

Page 6 - Features; Compliant with 802.3af specification

Features 8 ×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 4-port PoE function (port-1 ~ port-4) Compliant with 802.3af specification Supports PoE power up to 15.4W for PoE port Supports PoE power up to 30W for all PoE ports Supports PoE Powered Device (PD) classification identi...

Page 7 - Package Content; rubber

Package Content Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: – FSW-0809 – AC power adapter (Output: DC48V, 0.8A) – Four rubber feet – User Manual If any item is found missing or damaged, please contact your local reseller ...

Page 8 - Hardware Description; Front Panel; The PoE ports will not offer the power to

Hardware Description This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel LED Indicator: Comprehensive LED indicators display the status of the switch and the network (see the LED Indicators chapter below). Rear Panel PoE Ports (Port 1~4): These ports are...

Page 10 - LED Indicators; System Power

LED Indicators The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. System Power On : When the Power LED lights on, the Switch is receiving power. Off : When the Power turns off or the power cord has improper connection. PoE status (Port 1 ~ Port 4)...

Page 11 - PoE MAX

PoE MAX On : When the system was connected to PoE PD and the power resource remain <=7.5W, the LED lights on, the system will not provide power to the additional PoE PD inserted. Off : When the system have enough power of >7.5W. Ethernet port status (Ports 1~8) 10/100M Link/ACT: Link/ ACT : Th...

Page 12 - PoE Rule; this function will help to protect the

PoE Rule PoE Max: this function will help to protect the PoE Switch and to stabilize the power transmitting to the powered device (PD). If the system power remain <= 7.5 watt, the PoE MAX LED will light on and the system will not provide power to the additional PoE PD to protect the PoE Switch it...

Page 14 - Installation; The power outlet should be within 1.82; Connecting Network Cable

Installation The setup of the Switch can be performed using the following steps: 1. The surface must support at least 1.5 Kg for the Switch. 2. The power outlet should be within 1.82 meters (6 feet) of the Switch. 3. Visually inspect the DC power jack and make sure that it is fully secured to the po...

Page 15 - Technical Specifications

Technical Specifications General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex) 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half dupl...