Lenovo ThinkServer RD530- Manuals

Page 2 - Item; if the server meets one of the following criteria:

The dimensions of the rack cabinet must meet the following requirements: Figure 1. The dimension requirements of the rack cabinet 1 Rear mounting flange 2 Front mounting flange 3 Front door of the rack cabinet The following table explains the dimension requirements of the rack cabinet. Table 1. The ...

Page 4 - Rail kit package; Notes; that they are optional.; Figure 2. Parts in the rail kit package

Rail kit package Before you begin the rack installation, remove all the parts from the rail kit package shipped with yourserver and lay all the parts on a working surface. Notes : • An optional cable management arm can help you to manage your cables. Contact your local Service Provider to purchase t...

Page 5 - Figure 3. Slide rail components; right slide rail is marked with R. The letter R stands for right.; Figure 4. Cable management arm components

The left slide rail and the right slide rail are almost the same. The illustration below shows the components ofthe left slide rail. Figure 3. Slide rail components 1 Front end of the slide rail 3 Rear end of the slide rail 2 Inner rail 4 Outer rail Note: The inner side of the left slide rail is mar...

Page 6 - Installing your server into a rack cabinet using the rail kit; Install the rail kit by doing the following:

Installing your server into a rack cabinet using the rail kit Before you begin, remove all the parts from the rail kit package and lay all the parts on a working surface.See “Rail kit package” on page 4 . The length of each slide rail ranges from 65 cm (25.6 inches) whencollapsed to 90 cm (35.4 inch...

Page 7 - Figure 6. Unlocking the slide rail lock; until the

b. Pull up the release latch 1 on the front end of the right slide rail. Keep the release latch in the raised position and pull out the slide rail lock 2 . Figure 6. Unlocking the slide rail lock c. Position the front part of the right slide rail to the mounting flange. Make sure that the front end ...

Page 9 - Figure 11. Connecting the cable management arm and the slide rail

d. Connect the arm marked with A and the arm-rail joint by pulling out the eject button 1 and inserting the arm into the arm-rail joint 2 . Figure 10. Connecting the cable management arm and the arm-rail joint e. Connect the arm marked with B and the slide rail by pulling out the eject button 1 and ...

Page 10 - Install the server by doing the following:; Figure 12. Fully extending the inner rails

3. Install the server by doing the following: a. Fully extend the inner rails on both sides until the inner rails cannot be pulled out further. Figure 12. Fully extending the inner rails 10

Page 11 - Figure 13. Securing the server

b. Position the server as shown in the following illustration. Mount and secure the pair of rail mount points at the rear 1 first. Then mount and secure the pair of rail mount points 2 . Finally, hold and press the slide rails towards the server until the rail mount points 3 are locked into place. F...

Page 12 - Figure 14. The rail mount points are locked into place

The following illustration shows what the rail mount points 3 look like when locked into place. Figure 14. The rail mount points are locked into place 12

Page 13 - into the rack cabinet

4. Lift the latch 1 on both sides to release the inner rails. Gently slide the inner rails with the server into the rack cabinet 2 . CAUTION:To avoid injury to fingers, keep hands free from the latch area when the latch approaches theouter rail. Figure 15. Sliding the inner rails with the server int...

Page 14 - Figure 16. Securing the server to the rack cabinet; Trademarks

5. Secure the server to the rack cabinet with an M6 x 16 screw on both sides of the front of the server. Figure 16. Securing the server to the rack cabinet Trademarks Lenovo and the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both. Other company, product, or servic...

Page 16 - Second Edition; Printed in China

Second Edition © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration“GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Printed in China (1P) P/N: 0A91...