Lenovo 4223 - Manuals

Chapter 1. About this manual This manual provides service and reference information for ThinkStation ® computers listed on the front cover. This manual is intended only for trained service personnel who are familiar with Lenovo ® computer products. Before servicing a Lenovo computer product, be sure...

Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting a...

Voltage-selection switch Some computers are equipped with a voltage-selection switch located near the power-cord connectionpoint on the computer and some computers do not have a voltage-selection switch. Before you installyour computer or relocate your computer to another country or region, you must...

1 2 PERIGO A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: • Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. • Conecte t...

Não: • Jogue ou coloque na água • Aqueça a mais de 100°C (212°F) • Conserte nem desmonte Descarte a bateria conforme requerido pelas leis ou regulamentos locais. PRECAUCIÓN: Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM, dispositivos de fibra óticaou transmissores) estiverem...

1 2 DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenterun danger. Pour éviter tout risque de choc électrique : • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au...

Connexion Déconnexion 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 3. Branchez les câbles d'interface sur des connecteurs. 4. Branchez les cordons d'alimentation sur des prises. 5. Mettez les unités SOUS TENSION. 1. Mettez les unités HORS TENSION. 2. ...

• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerkenund Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- undKonfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. • Zum Installieren, Transportieren und Öff...

Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegelverwenden. Strahlungsbereich meiden. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit...

• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. • Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o dannostrutturale. • Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima diaprire i c...

• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y losmódems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique locontrario en los procedimientos de instalación y configuración. • Conecte y desconecte los cables, como se describe...

Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta losiguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera coninstrumentos ópticos, y evite exponerse directamente al rayo láser. ≥18 kg (37 lbs) ≥32 ...

Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. Specifications This section lists the physical specifications for your computer. Dimensions Width: 210 mm (8.3 inches) Height: 485 mm (19.1 inches) (floor to top ...

The following table lists the programs that you can access from the Lenovo ThinkVantage Tools program. Toaccess a program, double-click the corresponding icon. Table 1. Program icon names in Lenovo ThinkVantage Tools Program name Icon name in Lenovo ThinkVantage Tools Create Recovery Media Factory R...

Note: If the Enhanced Backup and Restore icon in the Lenovo ThinkVantage Tools program is dimmed, it indicates that you need to install the ThinkVantage Rescue and Recovery program manually before enablingits features. To install the ThinkVantage Rescue and Recovery program, do the following: 1. Cli...

Chapter 4. General Checkout Attention The drives in the computer you are servicing might have been rearranged or the drive startup sequence mighthave been changed. Be extremely careful during write operations such as copying, saving, or formatting.Data or programs can be overwritten if you select an...

Chapter 5. Diagnostics The diagnostic program is used to test hardware components of your computer. The diagnostic program canalso report operating-system-controlled settings that interfere with the correct operation of your computer.You can use the preinstalled diagnostic program to diagnose comput...

Chapter 6. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardlessof which operating system you are using. However, the operating system settings might override any similarsettings in the Setup Utility program. Star...

Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, itis recommended to use a strong password that cannot be easily compromised. To set a strong password,use the following guidelines: • Have at least eight characters in lengt...

Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Password considerations” on page 38. Erasing lost or forgotten passwords (clearing CMOS) This section provides instructions on how to erase lost or forgotten passwords, such as a user pa...

The after power loss feature enables your computer to wake up when the power supply resumes after asudden loss of electricity. To enable the after power loss feature, do the following: 1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ After Power Loss , ...

Chapter 7. Configuring RAID This chapter provides instructions on how to install hard disk drives and configure Redundant Array ofIndependent Disks (RAID) for your computer. Depending on your computer model, RAID can be enabled byIntel Rapid Storage Technology enterprise (RSTe) or the LSI MegaRAID B...

• If five SATA hard disk drives or solid state drives are installed, the SATA hard disk drive enablement module (one to five hard disk drives) is required. • If any SAS hard disk drives are installed, the SAS hard disk drive enablement module (one to five hard disk drives) is required. For more info...

using this adapter, refer to the complete MegaRAID SAS Software User Guide that is available at http://support.lenovo.com/en_US/guides-and-manuals/detail.page?DocID=UM007543. This section provides information about the following topics: • “Installing SATA or SAS hard disk drives” on page 46 • “Enter...

Entering the LSI MegaRAID BIOS configuration utility This section provides instructions on how to enter the LSI MegeRAID BIOS configuration utility. To enter the LSI MegaRAID BIOS configuration utility, do the following: 1. During the computer startup, follow the instructions on the screen. 2. Press...

Deleting RAID volumes using the LSI MegaRAID BIOS configurationutility This section provides instructions on how to delete RAID volumes using the LSI MegaRAID BIOSconfiguration utility. To delete RAID volumes using the LSI MegaRAID BIOS configuration utility, do the following: 1. Enter the LSI MegaR...

Chapter 8. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first.Always begin with Chapter 4 “General Checkout” on page 33. This index can also be used to help youdecide which FRUs to have available when servicing a computer. If...

The following tables describes beep symptoms. Beep Symptom FRU/Action 2 short beeps CMOS setting error Perform the following actions in order. 1. Start the Setup Utility program and press F10 to save and exit. See Chapter 6 “Using the Setup Utilityprogram” on page 37. 2. Start the Setup Utility prog...

POST Error Message Description/Action CMOS battery failed The CMOS battery is no longer functional. Replace the battery. CMOS checksum error - defaults loaded Checksum of CMOS is incorrect. The computer loads the default configuration settings.This error might indicate that CMOS has become corruptdu...

Message/Symptom FRU/Action Printer problems 1. Printer 2. System board Program loads from the hard disk with a known-gooddiagnostics diskette in the first 3.5-inch diskette drive 1. Run the Setup Utility program and check Startup sequence. 2. Diskette drive 3. Diskette drive cable 4. System board 5....

Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 56 shows the locations of the connectors on the rear of yourcomputer. Some connectors on the rear of your computer are color-coded to help you determine where toconnect the cables on your computer. Figure 2....

The following table lists the major FRUs shown in Figure 3 “Locating major FRUs and CRUs” on page 57 andidentifies which FRUs also are self-service CRUs or optional-service CRUs. Notes: • Self-service CRUs: These CRUs unplug or are secured by no more than two screws. Examples of these types of CRUs ...

Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to yourcomputer to increase storage capacity and enable your computer to read other types of media. Internaldrives are installed in bays. In this manual, the bays are referred to a...

Chapter 10. Replacing FRUs This chapter provides information about the FRU replacement instructions. Important Be sure to read and understand Chapter 2 “Safety information” on page 3 before replacing any FRU. Theseprecautions and guidelines will help you work safely. Note: FRU replacements are to be...

required connector. Then, use the instructions that come with the option to help you make the connectionand install any software or device drivers that are required for the option. Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding...

5. Disengage the cover latch 1 and remove the cover. Place the cover on a flat surface. Figure 6. Removing the computer cover Removing and reinstalling the front bezel Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on pa...

3. Remove the front bezel by releasing the two plastic tabs on the left side and pivoting the front bezel outward. Figure 7. Removing the front bezel 4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, and th...

Figure 8. Opening the PCI card retainer 4. Depending on whether you are installing or replacing a PCI card, do one of the following: • If you are installing a PCI card, remove the appropriate metal card slot cover. • If you are replacing an old PCI card, grasp the old card that is currently installe...

Figure 9. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. 68 ThinkStation Hardware Maintenance Manual

b. If the card is held in place by a retaining latch, press the card retaining latch 1 as shown to disengage the latch. Grasp the card and gently pull it out of the card slot. 5. Remove the new PCI card from its static-protective package. 6. Install the new card into the appropriate card slot on the...

• If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 11. Removing a memory module • If you are installing a memory module, open the retaining clips of the memory slot into which you want to install the memory module. F...

9. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 13. Installing a memory module 10. To install t...

8. Connect the signal cable and the power cable to the new optical drive. Figure 18. Connecting the optical drive 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 65. What to do next: • To work with another piece of hardware, go to the appropriate section. • To c...

8. Slide the card reader with retainer into the card reader drive bay until it snaps into position. Figure 21. Installing the card reader 9. Reconnect the card reader cable to the system board. See “Locating parts on the system board” on page 58. 10. Reinstall the front bezel. See “Removing and rein...

Refer to the “Lithium battery notice” in the ThinkStation Safety and Warranty Guide for information about replacing and disposing of the battery. To replace the battery, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. S...

9. Follow the following sequence to install the four screws to secure each new heat sink and fan assembly. Do not over-tighten the screws. a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 . b. Partially tighten screw 3 , then fully tighten screw 4 , and then...

5. Press the tab, and then pivot the hard disk drive fan outward to remove it from the chassis. Figure 25. Removing the hard disk drive fan assembly 6. Position the hard disk drive fan, and then pivot the fan to insert the tab into the chassis. 7. Reconnect the hard disk drive fan cable to the syste...

Figure 27. Installing the rear fan assembly 7. Connect the rear fan assembly cable to the system fan connector on the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts rep...

What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 104. Installing or replacing a hard disk drive enablement module Attention: Do not open your computer or attempt a...

7. To install a new hard disk drive enablement module, align the hole in the hard disk drive enablement module with the plastic standoff on the system board, and then position the hard disk drive module overthe corresponding connector on the system board. Figure 34. Installing a new hard disk drive ...

5. Disconnect the front audio and USB assembly cables from the system board. See “Locating parts on the system board” on page 58. Note: Make sure you note the locations of the cables when you disconnect the cables from the system board. 6. Remove the two screws that secure the front audio and USB as...

Note: The internal speaker is only available on some models. To replace the internal speaker, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 64. 3. Locate the internal speaker ...

Installing the second microprocessor Attention: Do not open your computer or attempt any repair before reading and understanding the “Important Safety Information” on page 1. This topic provides instructions on how to install the second microprocessor. Depending on the model, your computer might com...

• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 39. Removing the microprocessor 8. Touch the static-protective package that contains the new microprocessor to any unpainted surface on the outside of the computer. Th...

12. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press down the small handle 2 and push the handle inward to lock the microprocessor retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microproce...

Figure 45. Opening the microprocessor retainer 8. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket. Place the old microprocessor on a static-protective surface. Notes: • Do not touch the gold contacts on the bottom of the microprocesso...

12. Pivot the microprocessor retainer downward to close the retainer. Figure 49. Closing the microprocessor retainer 13. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press down the small handle 2 and push the handle inward to lock the microprocesso...

Figure 53. Securing the microprocessor in the socket 3. Align the notch 1 of the microprocessor socket cover with the alignment key 2 of the microprocessor socket. Lower the socket cover straight down into the microprocessor socket on the system board. Figure 54. Installing the microprocessor socket...

12. To complete the installation or replacement, go to “Completing the parts replacement” on page 104. Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstall the computer cover andreconnect cables. Depending on the parts you installed o...

Chapter 11. Additional service information This chapter provides additional information that the service representative might find helpful. Security features Security features in this section include the following: • Passwords • Vital Product Data • Management Information Format (MIF) Hardware-contr...

Note: You can download a self-starting bootable disc image (known as an ISO image) with the system program updates to create a system-program-update disc. Go to:http://www.lenovo.com/support. To update (flash) the BIOS from a disc, do the following: 1. Turn off your computer. 2. Repeatedly press and...

Television output notice The following notice applies to models that have the factory-installed television-output feature. This product incorporates copyright protection technology that is protected by method claims of certain U.S.patents and other intellectual property rights owned by Macrovision C...

Index A Administrator, password 38 B battery, replacing 77, 102 boot-block recovery 106 C card reader, replacing 75 changing password 38 startup device sequence 40 CMOS, clearing 39 components, internal 56 computer cover removing 64 computer cover, reinstalling 104 connectors rear 56 connectors, con...