Lennox T300HT - Manuals

PLANNING YOUR INSTALLATION PAGE 5 FLOOR PROTECTION This appliance requires a non-combustible floor protection forember protection. If the floor protection is to be stone, tile,brick, etc., it must be mortared or grouted to form a continu-ous non-combustible surface. If a chimney connector extendshor...

PLANNING YOUR INSTALLATION PAGE 6 COMBUSTIBLE WALL CLEARANCE WARNING: IT IS VERY IMPORTANT THAT YOUOBSERVE THE MINIMUM CLEARANCES. There are listed clearances for your stove which weredetermined in a Laboratory test using various "classes"of stove pipe or chimney. Minimums are first establis...

INSTALLATION PAGE 7 BAFFLE PLATES This appliance has two heavy steel baffle plates that are installed in the upper firebox (over the steel secondary air supply tubes). During shipment and installation, the baffle plates might slide around, and may need to be repositioned (lined up to each other) and...

INSTALLATION PAGE 8 CHIMNEY INSPECTION Existing chimneys must be inspected before installingyour stove. Consult your local building department forchimney code requirements. A masonry chimney musthave a code approved liner. This liner must not havebroken or missing pieces. Some non-code masonrychimne...

INSTALLATION PAGE 9 RESIDENTIAL STANDARD/RESIDENTIAL REDUCED Using 6” Diameter Single Wall or 6” L-Vent Connector Pipe

INSTALLATION – COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS NOTES: 1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through systemand the chimney wall, to but not past the inner flue liner face. 2. A chimney connector shall not ...

PRODUCT FEATURES AND CONTROLS CARE AND OPERATION PAGE 11 PRIMARY AIR CONTROL The primary combustion air delivery is controlled by thePrimary Air Control Assembly (The control handle is lo-cated below the fuel door). The heat output can be con-trolled by pushing the control handle in, then incremen-t...

CARE AND OPERATION PAGE 12 PRIMARY AIR CONTROL The Model T300HT has one combustion air control lo-cated under the ash lip. Start-up: To provide sufficient combustion air to achieve a clean burn as quickly as possible, the T300HT has theability to supplement its primary air with extra "Start-Up&#...

CARE AND OPERATION PAGE 13 BREAK-IN PERIOD Your stove finish is a high temperature paint that requirestime and temperature to completely cure. W e recom-mend that you ventilate the house during the initial burns.The paint emits non-toxic odors during this process. KEEP YOUR HOUSE WELL VENTILATED DUR...

CARE AND OPERATION PAGE 14 REFUELING To refuel the stove, first move the primary air control tohigh (pulled out). Let the fire "liven up" for about one min-ute. Open the fuel door about 1/2" and hold in this posi-tion about 30 seconds or until stove is drafting well.Open the door and add...

CARE AND OPERATION PAGE 15 WHY SEASONED WOOD? The key to the success of a good fire that produces heatfrom a woodstove is the wood. It needs to be well-seasonednatural wood. What does “Well-Seasoned” mean? When a tree is cut down, the wood is green, full of sap andmoisture. This moisture content can...

MAINTENANCE PAGE 16 SMALL AREA PAINT TOUCH-UP The stove body is painted with a quality high-temperaturestove paint. Use only model TSPK-B Stove Paint, Catalog# 70K99. Do not touch-up your stove with any other paint. Using one small piece of 320 grit sand paper and lightlysand the blemish so that the...

MAINTENANCE PAGE 17 CLEANING BLOWER INTAKE If an optional blower kit (catalog #14M41) is installed, theblower air intake requires cleaning at least once a year toremove lint, dust, etc. If there are pets in the dwelling, theintake should be cleaned at least twice a year. CREOSOTE FORMATION AND NEED ...

TROUBLESHOOTING PAGE 18 SMOKES OUT FUEL DOOR WHEN OPEN (SEE ✸ ✸ ✸ ✸ ) 1. The primary air control is closed.2. The chimney is too cool. Set the primary air control on "HIGH" for a few minutes before opening the fuel door. 3. Excess creosote will not only restrict your draft but it will create...

SPECIFICATIONS : Model T300HT PAGE 19 Approximate heating capacity ........ Up to ~2000 Sq. Ft. ( ~590 Sq. M.) Flue position........................................ Top Flue collar size .................................... 6" (152 mm) Approx. burn time .............................. 6 to 8 hours...

REPLACEMENT PARTS FOR MODEL: T300HT For the location of the nearest Dealer for replacement parts, contact: Lennox Hearth Products1110 West Taft AvenueOrange, CA 92865 PAGE 20 Part No. Description / Cat. No. Door & Glass Parts 28M21 Door Assembly, Metallic Black Painted 28M23 Door Assembly, Ebony...

COMPONENT DIAGRAMS – Model T300HT-M Firebrick (Note: All bricks are 1 ¼” thick) Part/Catalog # Quantity Dimensions Part/Catalog # Quantity Dimensions FB-1 12 9 x 4 1/2” regular FB7 2 9 x 2 1/8” regular FB-2 2 9 x 4 1/2” w/notch FB23 4 5 x 1” regular FB-3 2 9 x 4 1/2” w/hole FB30 4 8 1/4 x 1” regular...

OPTIONAL ACCESSORIES- Model T300HT-M Note: Install and use accessories per instructions provided with the accessory kit. PAGE 22 Catalog # Model Description 14M41 BK-T30 Blower Kit (Includes Dial - A - Temp) 14M21 SSK Stove Stat (Automates Fan / Heat Sensor Kit) 70K99 TSPK-B Touch-up Spray Paint Kit...