Page 2 - please follow the instructions shown.
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Consiglio JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.com
Page 4 - Control elements
Control elements 1. Rotary Switch 2. Illuminated ring 3. ON/OFF key 4. Programming key 5. Draw-off key 1 cup 6. Draw-off key 2 cups 7. Maintenance key 8. Steam pre-selection key 9. Display dialog system 10. Water tank with carrying handle 11. Filler funnel for pre-ground coffee: 12. Bean tank cover ...
Page 5 - Contents
5 Contents 1. Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6 1.1 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6 1.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 6 - The coffee machine may only be used by instructed persons.; Preparing the IMPRESSA
6 Introduction Thank you for purchasing the IMPRESSA. To ensure perfect func-tioning of your IMPRESSA, carefully read this operating manualand keep it for future reference. Should you need more information or if you encounter particularproblems not specified in these operating instructions in suffic...
Page 8 - Adjusting the water hardness
8 FILLING SYSTEM CLOSE TAP Close the steam / hot water draw-off tap (14). HEATING PRESS RINSE Press the maintenance key (7). Machine carries out a rinsing operation. RINSING READY If BEANS FILL is displayed, press the coffee draw-off keyagain. Machine not filled with coffee beans yet. To get an exce...
Page 11 - Drawing off 2 cups of coffee
11 tank. Make sure that the pre-ground you use is not too fine.This may cause blocking of the system. In this case thecoffee only drips out of the coffee spout. If you have filled in too little powder, the message ADDMORE POWDER will be displayed. The IMPRESSA stopsthe operation and returns to "...
Page 13 - Before CLOSE TAP, steam may still escape the system.; Drawing off steam with the; Press the steam pre-selection key
13 STEAMREADY To draw off steam, open the steam/hot water draw-off tap (14)(Fig. 13). The illuminated ring (2) is active. You can adjust the steam draw-off time individually by turningthe Rotary Switch (1) until the required SEC are displayed. For example, 35 SEC If you do not change the steam draw-...
Page 17 - Programming the language
17 READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until CUPS MADE is displayed. CUPS MADE Now press the Rotary Switch (1) to start programming the itemCUPS MADE The total number of drawn off products is displayed. For example 100 ...
Page 19 - Fill coffee beans; Refill beans as described in Chapter 2.4.; Replacing the filter; Refer to Chapter 5.2 «Replacing the filter».; Cleaning the IMPRESSA; Clean the replaceable hot water nozzle after each use.
19 16.4 Fill coffee beans FILLBEANS Refill beans as described in Chapter 2.4. The message REFILL BEANS will disappear after you drawoff your next cup of coffee. We recommend that you clean the bean tank regularly beforerefilling beans, using a dry cloth. Before cleaning the tank,switch off the IMPRE...
Page 20 - Emptying the system; switched off
20 16.9 Emptying the system Precondition: IMPRESSA switched off This operation is required to protect the IMPRESSA againstfrost damage during transports. Place a container under the replaceable hot water nozzle (16). Press the steam preselection key (8) until the following message is displayed: OPEN...
Page 22 - Tips for perfect coffee; Grinding degree
22 20. Tips for perfect coffee Height-adjustable coffee spout (17) You can adjust the height of the coffee spout to the size of yourcups (Fig. 3) Grinding degree Refer to Chapter 2.5 «Adjusting the grinding gear». Preheating cups You can preheat the cups using hot water or steam. The smaller thecoff...
Page 25 - Legal information; Energy consumption Standby:
25 23. Legal information These operating instructions contain all the information requiredfor using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained inthese operating instructions is required for using the machine safelyas well as for ope...