Page 3 - TO THE PURCHASER; This manual contains valuable information about your; Customer Information
3 TO THE PURCHASER This manual contains valuable information about your new King Kutter II Rotary Tiller. It has been carefully pre-pared to give you helpful suggestions for operating, adjust-ing, servicing and ordering repair parts. Keep this manual in a convenient place for quick and easy referenc...
Page 4 - It is the purchaser and/or operator ’s responsibility to....
4 It is the purchaser and/or operator ’s responsibility to…. z z z z z Read and understand the information contained inthis manual. z z z z z Operate, lubricate, assemble and maintain the equip-ment in accordance with all instructions and safetyprocedures in this manual. z z z z z Inspect the equipm...
Page 5 - CONTENTS; ITEM
5 CONTENTS ITEM PAGE Safety ......................................................................... 6 Assembly Instructions ................................................ 8 Before Putting Into Service ........................................ 8 Safety Training .......................................
Page 6 - SAFETY
6 SIGNAL WORDS: The signal words DANGER, WARNING and CAUTION are used withthe safety messages in this manual and with each safety sign. Theyare defined as follows: DANGER: Indicates an immediate hazardous situation that, if notavoided, could result in serious injury or death. This signal word is to ...
Page 7 - EQUIPMENT SAFETY GUIDELINES
7 EQUIPMENT SAFETY GUIDELINES z Safety of the operator and bystanders is one of the main concerns in designing anddeveloping a tiller. However, every year accidents occur which could have been avoidedby a few seconds of thought and a more careful approach to handling equipment. You,the operator, can...
Page 8 - ROTARY TILLER ASSEMBLY INSTRUCTIONS; BEFORE PUTTING ROTARY TILLER INTO SERVICE; For all Grease Fittings use TYPE/grade II tube grease.
8 ROTARY TILLER ASSEMBLY INSTRUCTIONS STEP 1 With rotary tiller still in crate, lay flat on a level surface. Cut banding straps on the two (2) upright crateposts. STEP 2 Remove the top & upper side sections of the crate, leaving the rotary tiller resting on the bottom sec-tion. STEP 3 Remove tie...
Page 11 - SAFETY TRAINING
SAFETY TRAINING z Safety is a primary concern in the design and manufacturing of our prod-uct. Unfortunately, our efforts to provide safe equipment can be wipedout by a single careless act of an operator or bystander. z In addition to the design and configuration of equipment, hazard controland acci...
Page 12 - PREPARATION; STARTING AND STOPPING SAFETY
PREPARATION z Never operate the tractor and tiller until you have read and completely understand this manual,the Tractor Operator’s Manual, and each of the safety messages found on the safety signs onthe tractor and tiller. z Personal protection equipment including hardhat, safety glasses, safety sh...
Page 13 - OPERATIONAL SAFETY
1 3 OPERATIONAL SAFETY z The use of this equipment is subject to certain hazards that cannot beprotected against by the mechanical means or product design. All opera-tors of this equipment must read and understand this entire manual, pay-ing particular attention to safety and operating instructions,...
Page 15 - TRANSPORT SAFETY; Plan your route to avoid heavy traffic.
OPERATIONAL SAFETY continued... z Pass rotary tiller diagonally through sharp dips and avoid sharp drops toprevent “hanging up” tractor and rotary tiller. Practice will improve yourskills in maneuvering on rough terrain. Always cut down slopes, neveracross the face. Always check tractor manual for p...
Page 16 - Never stand between
ATTACHING TO TRACTOR WARNING Never stand between tractor and rotary tiller while backing up tractor to the hitch. STEP 1 Attach to tractor's category 1 three point hitch as described in theTractor's Operator’s Manual. STEP 2 Determine if the PTO shaft needs to be shortened. N O T E : Due to the many...
Page 19 - OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS STEP 1Before each use perform the maintenance described in maintenance section(page 20). S T E P 2Read, understand, and follow the information on safety training, preparation,starting and stopping safety, operational safety, transport safety warning sec-tions of this manual (p...
Page 20 - WARNING; Periodically check and maintain proper gear oil level.; NOTE: Use only a grade Type II tube grease.; Check tiller tines for cracks and breaks before every use.; MAINTENANCE SAFETY; Follow good shop practices.
NOTE: Do not allow the tractor engine or rotary tiller to bog down or stall. Thiscauses undue wear and tear on the tiller and tractor. If this continues to happenreduce ground speed and raise tilling depth of rotary tiller. Never attempt to re-move objects from the rotor bar until the tractor has be...
Page 21 - STORAGE SAFETY; Store the unit in an area away from human activity.
z Be sure electrical outlets and tools are properly grounded z Use adequate light for the job at hand. z Make sure there is plenty ventilation. Never operate the engine of the towingvehicle in a closed building. The exhaust fumes may cause asphyxiation. z Before working on this machine, disengage th...
Page 22 - Top View; SAFETY SIGN LOCATIONS
2 2 Top View SAFETY SIGN LOCATIONS The types of safety signs and locations on the equipment are shown in theillustration below. Good safety requires that you familiarize yourself withthe various safety signs, the type of warning and the area, or particularfunction related to that area, that requires...
Page 28 - TILLER: EXPLODED VIEW
Page 33 - TG SERIES SIDE GEARBOX PARTS LIST
3 3 Ref. Part Name Part Number 1 Retaining Ring 90mm 902005 2 3 5 7 9 14 15 16 18 19 20 Retaining Ring 40mm Pressure Plate Plug 1/2"-14 NPT Flat Washer (main) Bolt M-12-25 Bolt M-10-25 (pck. of 6) Spacer (output) Spacer (input) Seal Double LIp(Pkg-2) 3210C Dbl. Bearing (Ball) 1310 Self Aligning ...
Page 34 - TG SERIES TOP GEARBOX ASSEMBLY
Page 35 - TG SERIES TOP GEARBOX PARTS LIST
3 5 Ref. Part Name Part Number 1 Retaining Ring 72mm 902301 2 3 5 7 9 12 13 14 15 16 17 18 Retaining Ring 40mm Housing RTA-50 Sq. Hd. Plug 1/4"-18 NPT Bolt M-10-30 (pck. of 4) Shim Pack (pck. of 8) Output Gasket 0.5 mm Input Gasket 0.4 mm Input Gasket 0.2 mm Output Seal (Double Lip) Input Seal (...