Lennox 2800HT - Manuals

Lennox 2800HT – Manual in PDF format online.

Manuals:

Manual

Manual Lennox 2800HT

Summary

Page 2 - IMPORTANT WARNINGS; PAGE 2

IMPORTANT WARNINGS CAUTION: PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW ROOM HEATER. FOR YOUR SAFETY, FOLLOW THE INSTALLATION, OPERATION AND MAINTENANCE INSTRUC-TIONS EXACTLY, WITHOUT DEVIATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY,...

Page 3 - PAGE 3; TABLE OF CONTENTS; One - Installation and operation instructions man-

PAGE 3 TABLE OF CONTENTS Important Warnings .................................................2 Testing / Listing, EPA, Using this Manual................ 3 Planning Your Installation ..................................... 4-7 Installation .......................................................... 8-12...

Page 4 - PAGE 4; QUESTIONS TO ASK LOCAL BUILDING OFFICIAL; Rooms where the installation is not allowed?; FLOOR PROTECTION; If

PLANNING YOUR INSTALLATION PAGE 4 QUESTIONS TO ASK LOCAL BUILDING OFFICIAL A correct installation is critical and imperative for reduc-ing fire hazards and perilous conditions that can arise when wood burning appliances are improperly installed. The installer must follow all of the manufacturer's in...

Page 6 - PAGE 6; Venting Requirements for factory built fireplace:; HT liner or; HT LINER WITH ANY OTHER TYPE

PLANNING YOUR INSTALLATION PAGE 6 FACTORY BUILT FIREPLACES (Not Approved In Canada) In the USA, this appliance is approved for installation into a listed factory built solid fuel burning fireplace (built to UL 127 or ULC S610 standards). The fireplace fire-box must accept the insert without modifica...

Page 8 - INSTALLATION

INSTALLATION PAGE 8 FIREPLACE INSTALLATION • USA only - All masonry fireplace installations re-quire a minimum positive flue connection using a block-off plate or a positive seal past the bottom of the chimney flue tile liner. In Canada, a full reline is required. • Measure fireplace size to make ce...

Page 9 - POWER CORD CHANGEOVER

INSTALLATION PAGE 9 POWER CORD CHANGEOVER DANGER: Risk of electrical shock. Disconnect power before servicing appliance. Do not route power cord under or in front of appliance. To change the power cord from one side of insert to the other, perform the following steps: 1. Ensure power cord in NOT plu...

Page 10 - Offset Adapter; CORRECT

INSTALLATION PAGE 10 10. Offsets can be handled using an offset adapter (it aligns starter pipe with flue. See Offset Adapter , page 26 for ordering information). Do not push insert in completely until surround assembly is installed. Care should be used to ensure that this adjustable connector is or...

Page 11 - SURROUND ASSEMBLY; Pull the insert slightly forward to its desired; Test for air leaks by hold-; : Preferred method of attaching connector; POSITIVE FLUE CONNECTION FOR MASONRY FIREPLACE

INSTALLATION PAGE 11 SURROUND ASSEMBLY IMPORTANT: Do not face seal over chimney cooling air system on superior brand or any brand fireplace which is designed with the chimney cooling air system. 13. Pull the insert slightly forward to its desired position; attach the face shield using the sur-round ...

Page 12 - Filler Plate; Blower System; Blower System Controls; Located on right side of door at bottom of panel.; PRIMARY AIR CONTROL

INSTALLATION PRODUCT FEATURES AND CONTROLS PAGE 12 POSITIVE FLUE CONNECTION FOR MASONRY FIREPLACE (continued) A preferable installation is the positive flue connection (a positive seal between the flue extension and the chimney). This can be achieved by using a filler plate. A filler plate can be ma...

Page 13 - CARE AND OPERATION; The glass should be cleaned thoroughly with glass

CARE AND OPERATION PAGE 13 GOLD DOOR The doorframe is plated with 24-karat industrial grade gold and requires curing to harden the gold. Once it is cured it will never tarnish. Prior to burning this appliance the door-frame should be cleaned thoroughly with a good window cleaning solution and a soft...

Page 15 - BLOWER SYSTEM; Turn rocker switch to the off position (; Located on right side of door at bottom of panel; WIRING DIAGRAM

CARE AND OPERATION PAGE 15 BLOWER SYSTEM The Blower System consists of a ON / OFF rocker switch, a variable speed blower speed control switch (rheostat) located on the right side panel, a thermally activated switch (fan disc) and 4 axial blowers. When starting a fire, leave the blower system off unt...

Page 16 - ings

FUEL MAINTENANCE PAGE 16 BURN RECOMMENDED FUEL This appliance is approved for use with wood only. Use only natural dry untreated wood (see Important Warn- ings , page 2, #10). Do not burn particleboard scraps or pressed logs using bonding agents because they can produce conditions which will deterio...

Page 17 - MAINTENANCE; DOOR GASKET; Ensure stove is cold prior to cleaning; CLEANING BLOWERS; - This stove is approved for; Removal of Fireplace Insert for Inspection:; The chimney connector and

MAINTENANCE PAGE 17 DOOR GASKET A spun fiberglass gasket (3/4" [19 mm] in diameter) pro-vides the seal around the fuel door. Should this become frayed or damaged it should be replaced. Spun fiberglass "rope" gasketing can be purchased from your dealer. It must be the same diameter as the...

Page 18 - Cleaning –; If the chimney is to be cleaned without re-; In the event of a chimney fire -; Make sure the fuel door

MAINTENANCE PAGE 18 Cleaning – If the chimney is to be cleaned without re- moving the insert from the fireplace, the baffle plate (in the firebox) must first be removed. Chimney cleaning should only be done by a qualified chimney sweep. See following – Cleaning / Removing Baffle Plate . Cleaning / R...

Page 19 - TROUBLESHOOTING; * SMOKES OUT FUEL DOOR WHEN OPEN; ments

TROUBLESHOOTING PAGE 19 * SMOKES OUT FUEL DOOR WHEN OPEN 1. The primary air control is closed. 2. The chimney is too cool. Set the primary air control on HIGH setting with start-up control OPEN for a few minutes before opening the fuel door. 3. Excess creosote will not only restrict your draft but i...

Page 20 - OVERFIRING DAMAGE; Overfiring Caused From Improper Op-; Overfiring Caused From Improper Operation

TROUBLESHOOTING PAGE 20 OVERFIRING DAMAGE If the heater or chimney connector glows, you are overfir-ing. Other symptoms may include: Cracking, warping or burning out of components, gold door may turn color, stove glass may develop a haze, which will not come off with cleaning. Overfiring of a stove ...

Page 22 - Description

REPLACEMENT PARTS LIST – Model 2800HT PAGE 22 Part No. Description Door Parts G300 Door Assembly, Gold (Handle Included) 86-128 Gasket Kit, 3/4" Door Rope (Includes Adhesive) 27M81 Gasket Kit, Glass Channel 27M67 Clip Set, Glass G400-7 Glass, Large Arched 11 1/8 X 17" (Glass gasket not inclu...

Page 23 - Installation / Operation Manual

REPLACEMENT PARTS LIST – Model 2800HT For the location of the nearest dealer for replacement parts, contact: Lennox Hearth Products 1110 West Taft Avenue Orange, CA 92865 PAGE 23 Part No. Description MS2805 Marble Set, Green (Also requires 1 each 1053 & 4 each 1051) 1053 Cerawool Pad For Marble ...

Page 24 - COMPONENT DIAGRAMS – Model 2800HT; FIREBOX PARTS

COMPONENT DIAGRAMS – Model 2800HT PAGE 24 FIREBRICK (1 ¼” THICK) AIR CONTROLS FIREBOX PARTS DOOR ASSEMBLY HANDLE ASSEMBLY

Page 25 - SAFETY/LISTING LABEL; Zero Clearance Fireplace Kit; Actual Appearance

SAFETY/LISTING LABEL PAGE 25 Catalog # Model Description (Model) 14M78 OA2800-66 Offset adapter, 6” to 6” diameter 14M74 ZCFK-28 Zero Clearance Fireplace Kit 14M75 MFK-28 Masonry Fireplace Kit 70K99 TSPK-B Touch-up spray paint kit, black 12 oz Spray Can OFFSET ADAPTER Installations requiring offsets...

Page 27 - EPA LABEL

Page 28 - Service Service

Page 28 OWNERSHIP RECORDS Dealer’s Name: Dealer’s Address: City: State: Zip Code: Serial Number: Date of Purchase: Date Installed: Notes: SERVICE AND MAINTENANCE LOG Service Service Service Date Technician Description