Lennox 1003C - Manuals

PLANNING YOUR INSTALLATION PAGE 6 COMBUSTIBLE WALL CLEARANCES WARNING: IT IS VERY IMPORTANT THAT YOU OB-SERVE THE MINIMUM CLEARANCES. There are listed clearances for your stove which were deter-mined in a Laboratory test using various "classes" of stove pipe or chimney. Minimums are first es...

PLANNING YOUR INSTALLATION PAGE 7 ALCOVE CLEARANCES NOTE:" = inches, mm = millimeter, cm = centimeter Alcoves must have minimum dimensions of 84" (214 cm) height, 56" (142 cm) width and 24" (610 mm) maximum depth. Require pipe: Type L Vent pipe to the top of the stove. Manufactured (...

INSTALLATION PAGE 8 AIR INTAKE COVER The pedestal is equipped with an air intake cover (lo-cated at the top front of the pedestal). The air intake cover should be adjusted to the open position if outside combustion air is NOT provided. If outside combustion air is provided, adjust to the closed posi...

INSTALLATION PAGE 9 SECURING THE STOVE TO THE FLOOR Manufactured (Mobile) Homes Only Once the outside air floor duct is in position, replace the floor protector. Make sure that the floor protector's hole is aligned with the outside air opening. Next position and align the stove on the hearth pad. Ma...

INSTALLATION PAGE 10 CHIMNEY INSPECTION Existing chimneys must be inspected before installing your stove. Consult your local building department for chimney code requirements. A masonry chimney must have a code approved liner. This liner must not have bro-ken or missing pieces. Some non-code masonry...

INSTALLATION PAGE 11 DRAFT REQUIREMENTS The appliance is merely one component of a larger sys-tem. The other equally important component is the vent-ing system which is necessary for achieving the required flow of combustion air to the fire chamber and for safely removing unwanted combustion byprodu...

INSTALLATION See Pipe Manufacturers Instructions For Installation Requirements Of Venting Components And Vent Clearances. PAGE 12 RESIDENTIAL STANDARD Using 6” (152 mm) Diameter Single Wall Connector Pipe. Not Approved For Manufactured (Mobile) Homes. MANUFACTURED (MOBILE) HOME STANDARD Using 6” (15...

CARE AND OPERATI0N PAGE 14 ASH DRAWER The large ash drawer located on the left side of the ped-estal is designed to make cleaning easier by containing the ashes in a removable drawer. WARNING: DO NOT OPERATE THIS STOVE WITHOUT THE ASH DRAWER PROPERLY INSTALLED AND SE-CURED (SEALED), AS THIS WILL PRO...

CARE AND OPERATION PAGE 15 FUEL DOOR The gold or black door option is purchased separately, but is required. Install the door per instructions provided in kit (see page 28 for ordering information). WARNING: DO NOT OPERATE THIS STOVE WITHOUT THE DOOR PROPERLY INSTALLED AND SECURED AS THIS WILL PRODU...

CARE AND OPERATION PAGE 16 BREAK-IN PERIOD Your stove finish is a high temperature paint that re-quires time and temperature to completely cure. We rec-ommend that you ventilate the house during the initial burns. The paint emits non-toxic odors during this proc-ess. KEEP YOUR HOUSE WELL VENTILATED ...

CARE AND OPERATION FUEL PAGE 17 REFUELING To refuel the stove, open the bypass damper and move the primary air control to "HIGH." Let the fire "LIVEN UP" for about one minute. Open the fuel door about ½” (1 cm) and hold in this position about 30 seconds or until the stove is drafting...

FUEL MAINTENANCE PAGE 18 SEASONING GUIDE Softwoods – 6 months to 18 months Hardwoods – 12 months to 24 months Logs that are 5” (127 mm) diameter across or larger should be split in half, three pieces if over 8” (203 mm), and four pieces when over a foot (305 mm) across. If the tree was fell 2 to 4 y...

MAINTENANCE PAGE 19 DOOR / GLASS GASKET AND ASH DRAWER GAS-KET A 3/4" (19 mm) spun fiberglass gasket provides the seal around the fuel door and a 1/8” (3.2 mm) x 1” (25.4 mm) flat woven gasket glass provides the seal around the glass. A ½” (13 mm) flat fiberglass gasket provides the seal around ...

MAINTENANCE PAGE 20 CATALYST REPLACEMENT The normal expected life of a catalyst (catalytic com-bustor) is 10,000 to 12,000 hours if the appliance is op-erated correctly and proper fuels are used. If the cata-lyst has been deactivated, it should be replaced. Symp-toms of deactivation include – notice...

TROUBLESHOOTING PAGE 21 SMOKES OUT FUEL DOOR WHEN OPEN (see ✸ ) 1. The primary air control is closed. 2. The chimney is too cool. Set the primary air control on "HIGH" with the bypass damper control "OPEN" for a few minutes before opening the fuel door. 3. Excess creosote will not on...

TROUBLESHOOTING PAGE 23 OVERFIRING DAMAGE If the heater or chimney connector glows, the appli-ance is overfiring. Other symptoms may include: Cracking, warping or burning out of components, cata-lytic combustor may deteriorate, gold doors may turn color, stove glass may develop a haze which will not...

SPECIFICATIONS: Model 1003C PAGE 24 Maximum Log Length 18” (458 mm) Manufactured (Mobile) Home Approved Yes, U.S.A. and Canada Outside Air Provision Yes Flue Collar Size 6” (153 mm) Flue Position Top Stove Back to Flue Center 9” (229 mm) Width 25.25” (642 mm) Depth 27” (686 mm) Height (to flue) 34.5...

REPLACEMENT PARTS LIST: Model 1003C PAGE 25 ITEM NO DESCRIPTION Door Parts 27M65 Clip Kit, Glass G6000 Door Assembly, Black, H0533 (handle included) 14M72 Door Assembly, Gold, G3000 (handle included) 86-128 Gasket Kit, Door (3/4" rope, includes adhesive) 27M81 Gasket Kit, Glass (10' of 10580. se...

COMPONENT DIAGRAMS - Model 1003C PAGE 27 Catalytic Combustor System Components Damper Assembly Air Intake Draft Module Door Assembly Handle Assembly (P/N LB-102214) Torque Plate Nut Washers Handle Rod Coil Handle Secondary Air Tube Bypass Damper Control Damper Door Positioning Stops Tunnel Baffle Ca...

OPTIONAL ACCESSORIES - Model 1003C Note: Install and use accessories per instructions provided with the accessory kit. PAGE 28 Catalog # Model Description 14M67 OAFD-S Outside Air Floor Duct * 14M72 DK100-G Gold Door Kit * H0533 DK100-B Black Door Kit 14M22 BK-100 Blower Kit 14M21 SSK Stove Stat Kit...

OWNERSHIP RECORDS Page 31 Dealer’s Name: Dealer’s Address: City: State: Zip Code: Serial Number: Date of Purchase: Date Installed: Notes: SERVICE AND MAINTENANCE LOG Service Service Service Date Technician Description