Laney lainey all tube 'class a' heritage amplifier - Manuals

Page 2 - SAVE THESE INSTRUCTIONS

SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product2. The product should be powered by a three pin `grounded (or earthed...

Page 4 - con; Laney; OPERATING INSTRUCTIONS

BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the...

Page 5 - INTRODUCTION; Best wishes from all at Laney; Lyndon Laney CEO

INTRODUCTION The Dark Art: In an age where guitar players have developed an unhealthy fascination with pre-amp distortion, the fabled sound of a tube power amp being pushed hard has almost passed into history. Until now that is! The L20H’s hand wired 20W Class A Single Ended output stage oozes class...

Page 6 - Only use good quality guitar cable.; FRONT PANEL CONTROLS

HI INPUT: LO INPUT: ‘ . CLEAN VOL: BRIGHT: DRIVE: ‘Hi’ stands for high gain. This input is designed for the connection of low output level guitars making it well suited for guitars with single coiled or low gain humbucker type pickups. Use of high gain pickups in this input may drive the preamp too ...

Page 7 - drive to be switched remotely via a foot switch.); (Always switch off and disconnect the power cord when not in use); This led will be lit when the amplifier is switched on.

ability to drive the output stage at higher Drive Volume settings. Setting a high level on the Drive control and a low setting on the Drive Volume will give you a punchy hard rock lead tone, with the ability to again drive the output tubes at higher Drive volume settings. Having set the Drive and Dr...

Page 10 - Off; BLUES LEAD

Laney OPERATING INSTRUCTIONS QUICK START SETTINGS - suggestions only, experiment! L H 20 Page 10 /16 Off BLUES LEAD BLUES CLEAN ROCK

Page 11 - USER SETTINGS - Store your own cool sounds

Laney OPERATING INSTRUCTIONS L H 20 USER SETTINGS - Store your own cool sounds Page 11 /16

Page 12 - TUBE AMPLIFIER SURVIVAL TIPS

L H 20 Laney OPERATING INSTRUCTIONS TUBE AMPLIFIER SURVIVAL TIPS " Take care when moving the amplifier. Tubes are fragile glass components, they can easily be damaged if thrown in and out of transit vans, " Make sure the impedance of your cabinets matches the setting on your amplifier. Impro...

Page 13 - L20H CONNECTIONS WITH FX

Laney OPERATING INSTRUCTIONS L20H CONNECTIONS WITH FX L20H WITHEXTENSION CABINETS In p u t O u tp u t FX Controller Page 13 /16 L H 20 www.laney.co.uk Laney 8 O HMS I MPEDANCE 60W RMS P OWER R ATING L INK O UT I NPUT MADE IN THE UK BY LANEY SERIAL NUMBER: www.laney.co.uk Laney 8 O HMS I MPEDANCE 60W...

Page 14 - amplifier load and could cause damage to your amplifier system.; BLOCK DIAGRAM

Laney OPERATING INSTRUCTIONS Laney OPERATING INSTRUCTIONS General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, ...

Page 15 - SPECIAL FEATURES; Factory Pre-set Option

Laney OPERATING INSTRUCTIONS L H 20 This product conforms to the requirements of the following European Regulations, Directives & Rules:- CE Mark (93/68/EEC), Low Voltage (72/23/EEC), EMC (93/68/EEC), RoHS (EU2002/95/EC), WEEE (EU2002/96/EC) Page 15 /16 In order to reduce environmental damage, a...

Page 16 - POWER TO THE MUSIC; A N E Y

In the interest of continued product development, Laney reserves the right to amend product specification without prior notification. POWER TO THE MUSIC Laney L A N E Y A M P L I F I C A T I O N w w w . l a n e y . c o . u k