Page 2 - SAVE THESE INSTRUCTIONS; TT
SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product2. The product should be powered by a three pin `grounded (or earthed...
Page 4 - con; Laney; OPERATING INSTRUCTIONS
BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the...
Page 5 - INTRODUCTION; Lyndon Laney CEO
INTRODUCTION The Dark Art: In an age where guitar players have developed an unhealthy fascination with pre-amp distortion, the fabled sound of a tube power amp being pushed hard has almost passed into history. Until now that is! The TT50C and TT100C are modern versatile tube combo amplifiers. They f...
Page 6 - Sets the level of the clean channel channel pre-amplifier.; FRONT PANEL CONTROLS
MUTE TIGHT CHANNEL 1 2 3 DAMPING AMP REVERB REVERB REVERB 1 2 3 TREBLE TREBLE TREBLE MIDDLE MIDDLE MIDDLE REVERB FX MIX PRESENCE BASS BASS BASS VOLUME INPUT MASTER MASTER VOLUME 2 VOLUME 1 BRIGHT MODERN BRIGHT BRIGHT XPAND MODERN BOOST DRIVE DRIVE T T100 INPUT: Single jack input for connecting your ...
Page 7 - MASTER; Sets the overall ‘loudness’ of channel 2.; FRONT PANEL CONTROLS - continued
CHANNEL 2 SWITCH: Press in to activate Channel 2, the led will illuminate when active. Channel 2 is designed to be completely flexible giving punchy cleans, smooth blues and hard rock tones. This switch is footswitchable and midi controllable, for more information on midi see the midi section later ...
Page 8 - Sets the overall ‘loudness’ of channel 3.
MASTER Sets the overall ‘loudness’ of channel 3. VOLUME 1: Sets the overall listening level of the amplifier, Crank the Volume up to drive the output tubes harder. Having set your channel controls to your desired sound try backing off your guitar volume and tone controls for lots of other cool sound...
Page 9 - to 100% wet and any mix of the two in between. The main modes are:
factor in order to get the bass response you’re looking for. It is normal for this control to make a slicking sound when operated. MUTE: This mutes the output section of the amplifier and the line out socket. It does not affect the signal path through the pre-amplifier, so sends to the fx loops and ...
Page 10 - Main power switch for the unit.; (Always switch off and disconnect the power cord when not in use); REAR PANEL CONTROLS
POWER INLET SOCKET: Connect to your power source. Make sure the specified voltage is correct for your country! POWER FUSE: This is the main safety fuse for the unit. The fuse protects the AC power to the amplifier. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL. If a fuse blo...
Page 11 - EXTENSION LOUDSPEAKER:; This single; REAR PANEL CONTROLS - CONTINUED
Page 11/24 EXTENSION LOUDSPEAKER: This single jack socket can be used to connect an 8-16 ohm extension cabinet. When an extension cabinet is used the switch (36) should be moved to the on position. Failing to do so will result in masmatched impedance and will reduce the amplifiers performance and in...
Page 12 - The; Reverb; midi data; REAR PANEL CONTROLS - MIDI SECTION
Laney OPERATING INSTRUCTIONS The advantage of having midi in your guitar amplifier is that it allows your amplifier and external devices (like FX controllers) to talk with each other. At last you can press one button to select the amplifier channel, and choice of effects on multiple devices all at o...
Page 13 - REAR PANEL CONTROLS - continued
Laney OPERATING INSTRUCTIONS Page 13/24 MIDI THRU: Midi thru is a daisy chain buffered output of the midi in information. It is a 7 pin DIN socket supporting phantom power* Connect to the midi in of the next external midi equipped device in the chain if required. MIDI IN: The TT amplifier receives m...
Page 14 - Select the required patch on your pedal board/midi controller; MIDI APPLICATIONS NOTE 2: TT AMPLIFIER AND MIDI CONTROLLER; Further Possibilities
Laney OPERATING INSTRUCTIONS Page 14 /24 In this configuration the TT amplifier is a slave device ,its setting being called up by the midi controller. This midi controller could be a device which purely generates midi information or a multi effects pedal board. To setup the amplifier you need to do ...
Page 15 - QUICK START SETTINGS - suggestions only! Experiment; Crystal Clean
Laney OPERATING INSTRUCTIONS Page 15/24 QUICK START SETTINGS - suggestions only! Experiment TT 5 C/ TT 10 C 0 0 Crystal Clean Blues Clean Blues Lead
Page 16 - QUICK START SETTINGS - continued; Rock Rhythm
Laney OPERATING INSTRUCTIONS Page 16 /24 QUICK START SETTINGS - continued TT 5 C/ TT 10 C 0 0 Rock Rhythm Rock Lead Metal
Page 17 - USER SETTINGS - Store your own cool sounds here
Laney OPERATING INSTRUCTIONS Page 17/24 USER SETTINGS - Store your own cool sounds here TT 5 C/ TT 10 C 0 0
Page 18 - TUBE AMPLIFIER SURVIVAL TIPS; often short out. Tube amps don't like running into a short circuit.
Laney OPERATING INSTRUCTIONS TUBE AMPLIFIER SURVIVAL TIPS " Take care when moving the amplifier. Tubes are fragile glass components, they can easily be damaged if thrown in and out of transit vans etc. " Make sure the impedance of your cabinets matches the setting on your amplifier. Improper...
Page 19 - TUBE AMPLIFIER SURVIVAL TIPS - continued
V1 ECC83 (High Grade) 1st Gain Stage Channel 1 V2 ECC83 (High Grade) 1st Gain Stage Channel 2 V3 ECC83 (Standard) 2nd Gain Stage Channel 2 V4 ECC83 (Standard) 1st Gain Stage Channel 3 V5 ECC83 (Standard) 2nd Gain Stage Channel 3 V6 ECC83 (Standard) Power Driver Stage V7-10 EL34B-STR Output Tubes (MA...
Page 20 - amplifier load and could cause damage to your amplifier system.; TT SAMPLE SYSTEM 1
Laney OPERATING INSTRUCTIONS Laney OPERATING INSTRUCTIONS General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, ...
Page 21 - TT SAMPLE SYSTEM 2; Midi Controller
Laney OPERATING INSTRUCTIONS Page 21/24 Input FX Controller Output 8 Ohms Link Model RB115 Power Rating 300W Program Model RB115 Power Rating 300W Program Serial Number: Serial Number: Input Laney Power To The Music www.laney.co.uk D ESIGNED IN THE UK BY L ANEY 16 Ohms Link Model RB115 Power Rating ...
Page 22 - BLOCK DIAGRAM; with normal
Laney OPERATING INSTRUCTIONS Laney OPERATING INSTRUCTIONS Page 22/24 TT 5 C/ T 10 C 0 T 0 INPUT DRIVE DRIVE CHANNEL2 CHANNEL3 EQ EQ CHANNEL1 EQ VOLUME/ BRIGHT MASTER VOLUME LINE OUT FX SEND FX RETURN REVERB RETURN MUTE PRESENCE RECORD OUT FX MIX MASTER REVERB OUTPUT STAGE CHANNEL SWITCHING MASTER VO...
Page 23 - SPECIFICATIONS
Laney OPERATING INSTRUCTIONS Page 23/24 0 V H 1 0R Laney OPERATING INSTRUCTIONS Supply Voltage ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option Mains Fuse TT50C (~220V>240V = T2A L 250V) (~100>120V = T5A L 250V) HT Fuse TT50C = T1A L Power Consumption TT50C = 200W TT100C = 300W Output ...
Page 24 - POWER TO THE MUSIC; A N E Y
In the interest of continued product development, Laney Reserves the right to amend product specification without prior notification. POWER TO THE MUSIC Laney JAZZ AMPICONS ARE HERE TO HELP! BLUES ROCK METAL w w w . l a n e y . c o . u k L A N E Y A M P L I F I C A T I O N
