KTI Networks KS-2260 - Manuals
KTI Networks KS-2260 – Manual in PDF format online.
Manuals:
Manual KTI Networks KS-2260
Summary
- 3 - The information contained in this document is subject to change without priornotice. Copyright (C) KTI. All Rights Reserved. TRADEMARKSEthernet is a registered trademark of Xerox Corp. WARNING:This equipment has been tested and found to comply with the limits for a Class Adigital device, pursu...
- 4 - Table of Contents 1. Introduction ................................................................ 8 1.1 Introduction .................................................................................... 81.2 Features ................................................................................
- 8 - 1. Introduction 1.1 Introduction Driven by recent advances in desktop computing technology, today’snetwork applications have increased in speed, power and the ability toprocess information. To meet the demands of these more bandwidth-intensive applications, this switch device provides signific...
- 1 0 - 1.3 Hardware Specifications 10/100 Switched Ports Port 1 ~ 24, Total : 24 ports 802.3 10Base-T, 802.3u 100Base-TX compliantShielded RJ-45 with auto MDI-X function Port 23, 24 Alternatives 100Base-FX connectivity 2 expansion module slots - Slot F23, F24 Giga Switched Ports 2 expansion Slots -...
- 1 2 - 1.4 Software Specifications Management interface In-band SNMP over TCP/IP networkIn-band Web browser over TCP/IP networkIn-band Telnet over TCP/IP networkOut-of-band via Console portSNMP Traps over TCP/IP network RFC & Protocols IPv4 IP version4 RFC791 TCP Transmission Control Protocol R...
- 1 5 - 1.5 Function Descriptions 1.5.1 LACP Trunking Function The switch provides a trunking function, which is compliant with 802.3adstandard. 802.3ad is a specification from IEEE that allows us to bundleseveral physical port links together to form one logical port , called atrunk between two devi...
- 2 6 - 1.5.9 QoS Priority Function This switch supports two priority levels, high and low, and provides twopriority functions:1. Port-based Priority (Static priority)2. 802.1p Priority (VLAN tagged priority) Priority Classification MethodsStatic priority is called port-based priority. The priority ...
- 3 0 - 2. Installation and Management 2.1 Panel Description 2.2 AC Power Supply One AC power cord which meets the specification of your country oforigin was supplied with the switch unit. Before installing AC power cordto the switch, make sure the AC power switch is in OFF position and theAC power ...
- 3 1 - 2.3 Network Switched Ports The switch provides three types of switched ports as follows:Port Number Label Specifications Port Type Modules Port 1 - 22 1 - 22 Fixed RJ-45 10/100TX No Port 23 - 24 23 - 24 Fixed RJ-45 10/100TX No F23 - F24 Module slot 100FX Optional Port 25-26 G1 - G2 Module sl...
- 3 4 - 2.3.3 Gigabit Ports and Modules Port 25 and Port 26, labeled G1 and G2 respectively, support the followingGigabit modules: Part Number Connector Cable Distance 2260-GT RJ-45 Cat.5e 100m 2260-SXC Duplex SC MMF 62.5/125mm 220m MMF 50/125mm 500m 2260-SXL Duplex LC MMF 62.5/125mm 220m MMF 50/125...
- 3 5 - Specifications Part Number Compliance Speed Duplex 2260-GT IEEE 802.3ab 1000BASE-T 1000Mbps Half / Full IEEE 802.3u 100BASE-TX 100Mbps Half / Full IEEE 802.3 10BASE-T 10Mbps Half / Full Auto-negotiation functionMDI-X RJ45 2260-SXC IEEE 802.3z 1000BASE-SX 1000Mbps Full 2260-SXL IEEE 802.3z 10...
- 4 0 - 2.7.1 Setup for Out-of-band (Console) Management Before doing any in-band management, it is necessary to perform con-sole operation for configuring IP and SNMP related settings for the firsttime the switch is received for installation. Any PC running Windows 95/98/ or NT can be used as a con...
- 4 1 - 2.7.2 Setup for In-band Management To perform an in-band management, it is necessary to connect the sys-tem to your TCP/IP network. The steps are: 1. Configure IP and SNMP related settings to the device using direct console management when you receive it first time for the installa-tion. 2. ...
- 4 2 - 3. Console and Telnet Operation This chapter describes the detailed console operation. It can be appliedto either out-of-band console management or in-band Telnet manage-ment. Refer to Chapter 2 for installation details. Cold StartWhen the power to the switch is turned on, the device start i...
- 4 4 - 3.1 Main Menu When login successfully, the main menu is shown as follows: --------------------------------------------- Main Menu Switch Static Configuration Protocol Related ConfigurationStatus and CountersReboot SwitchTFTP Update FirmwareL o g o u t Configure the switch. Arrow/TAB/BKSPC = ...
- 4 5 - The following operation convention is commonly used for later configu-ration pages: Action menu: <Quit> Exit configuration <Edit> Edit each configuration value <Save> Save all configured values <Previous Page> Browse previous configuration page <Next Page> Brows...
- 4 6 - 3.2 Switch Static Configuration [Switch Static Configuration] menu is shown as follows: ---------------------------------------------------- Managed 24+2G Switch : Switch Configuration Port Configuration Trunk ConfigurationVLAN ConfigurationMisc ConfigurationAdministration ConfigurationPort ...
- 4 7 - 3.2.1 Port Configuration The following page illustrates Port 1 ~ Port 8 configuration example: ------------------------------------------------------------------------- Managed 24+2G Switch : Port Configuration InRate OutRate FlowControl Port Type (100K) (100K) Enable Auto Spd/Dpx Full Half ...
- 4 8 - Port : Port numberDisplay names - PORT1 - PORT24, G1 - G2 Type : Port typeDisplay names - 100Tx, 100FX, 1000T, 1000FX InRate : Input (Ingress) rate control setting, 100Kbytes per unit.Options - 0 = disable rate control, 1 ~ 1000 valid rate value OutRate : Output (Egress) rate control setting...
- 4 9 - 3.3.2 Trunk Configuration Trunk configuration example page ------------------------------------------------------------------------- Managed 24+2G Switch : Trunk Configuration 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 G1 G2 1 V V V V - - - - - - - - - - - - - - ...
- 5 0 - 3.3.3 VLAN Configuration ---------------------------------------------------- Managed 24+2G Switch : VLAN Configuration VLAN Configure Create a VLAN GroupEdit/Delete a VLAN GroupGroup Sorted ModePrevious Menu Configure the VLAN pvid and ingress.egress rules Tab=Next Item BackSpace=Previous I...
- 5 2 - 3.3.3.2 Create a VLAN Group Create a Port-based VLAN group ---------------------------------------------------- Add a VLAN Group VLAN Name: [Vlan2 ] Grp ID:[ 2 ] ( 1 ~ 4 0 9 4 ) Port M e m b e r ----------------------- PORT1 Member PORT2 Member PORT3 No PORT4 No PORT5 No PORT6 No PORT7 No PO...
- 5 4 - Member : Give a member setting, Options - UnTagged : the specified port is a member port and outgoing framesare not tagged.Tagged : the specified port is a member port and outgoing framesare tagged.No : the specified port is not a member port Note:If more than two VLAN groups are configured ...
- 5 5 - Example to edit Vlan2 group: ---------------------------------------------------- Edit a VLAN Group VLAN Name: [Vlan2 ] VLAN ID:[2 ](1~4094) Protocol VLAN : AppleTalk/NetBIOS Port Member -----------------------PORT1 UnTagged PORT2 Tagged PORT3 UnTagged PORT4 No PORT5 No PORT6 No PORT7 No POR...
- 5 6 - 3.3.4 Misc Configuration ---------------------------------------------------- Managed 24+2G Switch : Misc Configuration MAC Age Interval Broadcast Storm FilteringMax bridge transmit delay boundPort SecurityCollision Retry ForeverHash AlgorithmPrevious Menu Configure the MAC aging time Tab=Ne...
- 6 0 - 3.3.4.5 Collision Retry Forever ---------------------------------------------------- Managed 24+2G Switch : Collision Retry Forever Collision Retry Forever : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- Collision Retry contro...
- 6 1 - 3.3.5 Administration Configuration ---------------------------------------------------- Managed 24+2G Switch : Device Configuration Change Username Change PasswordDevice InformationIP ConfigurationPrevious Menu ---------------------------------------------------- 3.3.5.1 Change Username ----...
- 6 2 - 3.3.5.2 Change Password ---------------------------------------------------- Managed 24+2G Switch : Password Configuration Old Password : xxxxNew Password : xxxxenter again : xxxx action-> <Edit> <Save> <Quit> ---------------------------------------------------- The pass...
- 6 3 - 3.3.5.4 IP Configuration ---------------------------------------------------- Managed 24+2G Switch : Device Configuration D H C P : Disabled IP Address : 192.168.0.2Subnet Mask : 255.255.255.0G a t e w a y : 192.168.0.1 action-> <Edit> <Save> <Quit> ---------------------...
- 6 4 - 3.3.6 Port Sniffer Configuration ---------------------------------------------------- Managed 24+2G Switch : Port Sniffer Sniffer Mode : RxSniffer Port : PORT1Monitored Port: Port M e m b e r ---------------------- PORT1 - PORT2 - PORT3 V PORT4 - PORT5 V PORT6 - PORT7 - PORT8 - action-> &...
- 6 5 - 3.3.7 Priority Configuration ---------------------------------------------------- Managed 24+2G Switch : The Priority Configuration Port Static Priority 802.1p PriorityPrevious Menu ---------------------------------------------------- Two priority methods are provided: • Port Static Priority...
- 6 8 - 3.3.8 MAC Address Configuration ---------------------------------------------------- Managed 24+2G Switch : MAC Address Configuration Static MAC Address Filtering MAC AddressPrevious Menu ---------------------------------------------------- 3.3.8.1 Static MAC Address ------------------------...
- 6 9 - Add static MAC address ---------------------------------------------------- Managed 24+2G Switch : Add Static MAC Address MAC Address : 0040F6FE0005 Port Num : PORT3 Vlan ID : 2 action-> <Edit> <Save> <Quit> ---------------------------------------------------- MAC Addres...
- 7 0 - 3.3.8.2 Filtering MAC Address Refer to Chapter 1 for description of MAC address filtering function. Theoperations to Add/Edit/Delete a filter MAC address are similar to theoperations for static MAC address table. The following page shows anexample of filter MAC address table: ---------------...
- 7 1 - 3.4 Protocol Related Configuration ---------------------------------------------------- Managed 24+2G Switch : The Protocol Related Configuration S T P S N M PG V R PI G M PL A C P8 0 2 . 1 xPrevious Menu ---------------------------------------------------- 3.4.1 STP ------------------------...
- 7 2 - STP Enable ---------------------------------------------------- Managed 24+2G Switch : STP Enabled/Disabled Configuration S T P : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- Spanning Tree function can be enabled or disabled....
- 7 4 - Perport Configuration ---------------------------------------------------- Managed 24+2G Switch : STP Port Configuration Port P o r t S a t e P a t h C o s t P r i o r i t y --------------------------------------------- PORT1 Forwarding 1 0 1 2 8 PORT2 Forwarding 1 0 1 2 8 PORT3 Forwarding 1...
- 7 5 - 3.4.2 SNMP ---------------------------------------------------- Managed 24+2G Switch : SNMP Protocol System Options Community StringsTrap ManagersPrevious Menu ---------------------------------------------------- Use this page to setup SNMP related parameters and SNMP trap hostsrelated param...
- 7 6 - 3.4.2.2 Community Strings ---------------------------------------------------- Managed 24+2G Switch : SNMP Community Configuration Community Name Write Access --------------------------------------------- public Restricted private Unrestricted action-> <Add> <Edit> <Delete&...
- 7 7 - 3.4.2.3 Trap Managers A trap manager is a management station that allows to receive SNMPtraps. An SNMP trap is issued by the switch when the associated trapevent occurs in the switch. A trap manager is defined by its IP addressand a community string. Up to three trap managers can be configur...
- 7 8 - 3.4.3 GVRP This page you can enable or disable the GVRP (GARP VLAN Registra-tion Protocol) support. ---------------------------------------------------- Managed 24+2G Switch : GVRP Configuration G V R P : Enabled action-> <Edit> <Save> <Quit> ----------------------------...
- 7 9 - 3.4.5 LACP This menu list is used to configure LACP trunk groups. ---------------------------------------------------- Managed 24+2G Switch : LACP Configuration Working Ports Setting State ActivityLACP StatusPrevious Menu ---------------------------------------------------- 3.4.5.1 Working P...
- 8 1 - 3.4.5.3 LACP Status ---------------------------------------------------- Managed 24+2G Switch : LACP Group Status Group Key : 1P o r t _ N o : 1 2 3 4 action-> <Quit> <Previous Page> <Next Page> ---------------------------------------------------- This page shows LACP st...
- 8 2 - 3.4.6.1 Enable 802.1X Protocol ---------------------------------------------------- Managed 24+2G Switch : 802.1x Enabled/Disabled Configuration 8 0 2 . 1 x : Enabled action-> <Edit> <Save> <Quit> ---------------------------------------------------- This menu is used to ...
- 8 4 - 3.4.6.4 802.1X Misc. Configuration ---------------------------------------------------- Managed 24+2G Switch : 802.1x Misc Configuration Quiet-period <0..65535, default=60> : 60 Tx-period <0..65535, default=30> : 30 Supplicant-timeout <0..300, default=30> : 30Server-timeout...
- 8 5 - 3.5 Status and Counters ---------------------------------------------------- Managed 24+2G Switch : Status and Counters Port Status Port CountersSystem InformationPrevious Menu ---------------------------------------------------- Menu functions: Port Status : display the status of all switch...
- 8 7 - 3.5.2 Port Counters ------------------------------------------------------------------------- Managed 24+2G Switch : Port Counters Port TxGoodPkt TxBadPkt RxGoodPkt RxBadPkt TxAbort Collision DropPkt---------------------------------------------------------------------------PORT1 0 0 0 0 0 0 ...
- 8 9 - 3.6 Reboot Switch ---------------------------------------------------- Managed 24+2G Switch : Restart Configuration R e s t a r t D e f a u l t Previous Menu ---------------------------------------------------- 3.6.1 Restart This command will reboot the switch with current configuration sett...
- 9 0 - 3.7 TFTP Update Firmware ---------------------------------------------------- Managed 24+2G Switch : TFTP Update Firmware Configuration TFTP Update Firmware TFTP Restore ConfigurationTFTP Backup ConfigurationPrevious Menu ---------------------------------------------------- This menu support...
- 9 1 - 3.7.1 TFTP Update Firmware ---------------------------------------------------- Managed 24+2G Switch : TFTP Update Firmware TFTP Server : 192.168.0.15 Remote File Name : image.bin action-> <Edit> <Save> <Quit> ---------------------------------------------------- The step...
- 9 2 - 3.7.2 TFTP Restore Configuration ---------------------------------------------------- Managed 24+2G Switch :Restore Configuration File TFTP Server : 192.168.0.15 Remote File Name : data.dat action-> <Edit> <Save> <Quit> ---------------------------------------------------...
- 9 3 - 3.7.3 TFTP Backup Configuration ---------------------------------------------------- Managed 24+2G Switch :Upload Configuration File TFTP Server : 192.168.0.15 Remote File Name : newdata.dat action-> <Edit> <Save> <Quit> --------------------------------------------------...
- 9 5 - 4.1 Configuring SNMP Settings via Console Operation Before performing SNMP operation, proper SNMP settings must be con-figured. The SNMP related settings are: Name : Logic name to identify the switch unitLocation : Location where the switch unit is installedContact : Contact person regarding...
- 9 6 - The following MIB-2 objects are related to the switched ports and areindexed by a port number 1 ~ 27 (27 = CPU port): Port MIB-2 Objects Set/Get Value Options ifIndex.1 ~ 27 Get Physical port number ifDescr.1 ~ 26 Get text - Port 1~26 on unit 1 ifDescr.27 Get text - ethernet switch low drive...
- 9 8 - 4.3 SNMP Traps The switch supports the following SNMP traps. When the trap eventoccurs, the SNMP agent will generate a trap notification to SNMP trapmanager stations. Up to three trap managers can be supported. Each trapmanager must be configured with : IP address and Community stringwhich t...
- 1 0 0 - 5.1 Start Browser Software and Making Connection Start your browser software and enter the IP address of the device unit towhich you want to connect. The IP address is used as URL for thebrowser software to search the device. URL : http://xxx.xxx.xxx.xxx/ Factory default IP address : 192.1...
- 1 0 1 - 5.2 Web Management Home Overview This page provides the following menu list. Each menu is describedindividually in the following sections. • Menu • Port Status • Port Statistics • Administrator • TFTP Update Firmware • Configuration Backup • Reset System • Reboot
- 1 0 2 - 5.3 Port status This page shows all port status in a scroll bar list. The status are depen-dent on user settings and the negotiation results as follows: State : Display port function status including - Config : function setting - On = enable, Off = disableAtual : status - On = enabled, Off...
- 1 0 6 - 5.5.1 IP Address Available settings:DHCP : DHCP function setting Enable : enable DHCP client function to get dynamic IP addressDisable : disable DHCP client function and use static IP address IP Address : Static IP address assigned to the managed switch unitSubnet_Mask : subnet mask settin...
- 1 0 9 - 5.5.2.3 Advanced Miscellaneous settings : MAC Address Age-out Time : Type the number of seconds that aninactive MAC address remains in the switch address table. The validrange is 300~765 seconds (must be multiple of 3). Default is 300 seconds. Max bridge transmit delay bound control : Limi...
- 1 1 3 - 5.5.4 Port Controls This page allows to change per port configuration settings as follows: Port : Select the ports to perform setup. More than one port can beselected at the same time for setup. See next page for control settings. Note:All default values displayed for setup are not current...
- 1 1 8 - Two Static Trunking groups are configured.
- 1 2 6 - A Port-based VLAN group contains the following settings: VLAN name : Name of the VLAN groupGroup ID : Unique ID for the groupMember ports : list of ports belonging to the group ID Click [Apply] to confirm the changes. Note:If the trunk groups exist, you can see it (ex:TRK1,TRK2…..) in sele...
- 1 2 8 - Add a new VLAN Basic page settings:VLAN Name : name for the new VLANVID : VLAN ID of the new VLAN (value: 2-4094, default: 1)Protocol Vlan : setting for protocol support as follows: NoneIP, ARP, AppleTalk/NetBIOSNovell_IPX, Banyan_Vines_C4 / Novell IPX(raw Ethernet)Banyan_Vines_C5 / Spanni...
- 1 2 9 - Edit member ports : select member ports from available port box [Add] - add one member port[Remove] - remove a member port Click [Next] : to set tag/untag mode for the member ports Note:If more than two VLAN groups are configured with same protocol value,make sure the member ports of those...
- 1 3 0 - Port VID Settings Click [Port VID] to set per port VID and Ingress filtering rules. Multipleport selection at the same time for same settings is allowed. Port VID Settings:Port VID (PVID) : the port VLAN ID that will be assigned to untaggedtraffic on a given port. The range is 1~255, defau...
- 1 3 4 - STP port parameters settings: Port Priority : Priority value for becoming the root port. The rage is 0-255, default setting is 128, the lowest number has the highest priority.Path Cost : Specifies the path cost of the port that switch uses to deter-mine which port are the forwarding ports ...
- 1 3 5 - 5.5.9 Port Sniffer Sniffer Mode : Select one of sniffer modes, options - DISABLE : Disable sniffer functionRX : All Rx traffic on monitored ports are copied to Analysis portTX : All Tx traffic on monitored ports are copied to Analysis portBOTH : Both Rx and Tx traffic are copied to Analysi...
- 1 3 6 - 5.5.10 SNMP SNMP Parameters This page is used to configure SNMP related parameters as follows:Name : Name to be used for the switch.Location : The location of the switch.Contact : A name of a person or organization Click [Apply] to apply the settings.
- 1 3 7 - SNMP Managers Community String and access control settings:Community String : The community string serves as a password whichallows remote SNMP manager stations to access the switch managementobjects via SNMP protocol. Max. Up to 4 community strings are sup-ported. RO : Access right for Re...
- 1 3 8 - SNMP Trap Managers A trap manager is a management station which can receive SNMP trapmessages sent by the switch when predefined trap events occur. SNMP Trap Manager settings:IP address : IP address of the trap manager stationCommunity : Community string belonging to the trap manager Click...
- 1 4 0 - 5.5.12 802.1X Configuration This menu includes three 802.1X function related settings: System Configuration : Parameters for connection to a Radius serverPerPort Configuration : Per port 802.1X mode settingsMisc Configuration : 802.1X protocol related timers and parameters
- 1 4 4 - 5.6 TFTP Update Firmware The steps to update the firmware of the switch are: 1. Start your TFTP server. 2. Copy the firmware image file of new version into the TFTP server. 3. In this web page, specify the IP address of the TFTP server, in where the new firmware image file is stored. 4. In...
- 1 4 6 - 5.7 Configuration Backup 5.7.1 TFTP Restore Configuration The function is used to download a new default configuration file from aTFTP server into the switch. The steps are:1. Start your TFTP server. 2. Copy the new default configuration file into the TFTP server. 3. In this web page, spec...
- 1 4 7 - 5.7.2 TFTP Backup Configuration This function is used to backup (upload) current configuration settingsof the switch unit onto a TFTP server. The steps are: 1. Start your TFTP server. 2. In this web page, specify the IP address of the TFTP server, to where the current configuration data is...
- 1 5 0 - 6. Update Firmware from Console The switch also supports firmware update from console port. Theoperation is performed over 1K Xmodem protocol. Cases to update firmware from console:1. Power on the switch and press any key from console within 5 seconds. The switch enters 1K Xmodem receiver ...
- 1 5 1 - Appendix A: Factory Default Settings IP Address Related Settings DHCP Disabled Static IP Address 192.168.0.2 Subnet Mask 255.255.255.0 Default Gateway 192.168.0.1 Per Port Settings Port Function Enabled Auto-negotiation Auto Speed 100Mbps (Port 1-Port 24)1000Mbps (Port G1, G2) Duplex Full ...
KTI Networks Manuals
-
KTI Networks KT-10T
Manual
-
KTI Networks DH-8T
Manual
-
KTI Networks Ethernet Media Converter
Manual
-
KTI Networks KCD-302 Series
Manual
-
KTI Networks KG-502T
Manual
-
KTI Networks KF-221FX Ver.C
Manual
-
KTI Networks KF230TX
Manual
-
KTI Networks KSC-240
Manual
-
KTI Networks KS-115FM-V
Manual
-
KTI Networks KCD-302
Manual
-
KTI Networks KCD-400 Series
Manual
-
KTI Networks KF-310L
Manual
-
KTI Networks KF-310
Manual
-
KTI Networks KC-10FM
Manual
-
KTI Networks KC-1300
Manual
-
KTI Networks KS-117FM-V
Manual
-
KTI Networks KC-300DM
Manual
-
KTI Networks KC-300D
Manual
-
KTI Networks KCD-300
Manual
-
KTI Networks 221TX/3
Manual