KTI Networks KS-108F - Manuals

Page 3 - TRADEMARKS; Ethernet is a registered trademark of Xerox Corp.; FCC NOTICE; Marking by the symbol

- 3 - The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation issubject to the following two cond...

Page 4 - Table of Contents

- 4 - Table of Contents 1. Introduction .................................................................. 5 1.1 Features ........................................................................................... 61.2 Specifications .....................................................................

Page 5 - The key features of the switch series are:; Optimized Bandwidth; a connectivity to a Fast Ethernet network via fiber cable.; Easy Installation

- 5 - 1. Introduction This 8-port Fast Ethernet switch series provides seven 10/100 TP portsand one 100BASE-FX fiber port, each capable of transmitting or receiv-ing information simultaneously at full wire speed to control and allocatethe network bandwidth. The key features of the switch series are:...

Page 7 - K entries

- 7 - 1.2 Specifications 10/100 Ports IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX std.Shielded RJ-45 jacks with Auto MDI-X detectionAuto-negotiation capableSpeed for 10Mbps or 100MbpsFull-duplex or half-duplex mode support 100FX Port IEEE 802.3u 100BASE-FX compliantFixed 100Mbps operationDuplex mode...

Page 8 - 00FX Port Fiber Specifications; Single Fiber Bi-Di WDM Series

- 8 - 100FX Port Fiber Specifications KS-108FB-xxx Duplex Series Model Ext Fiber Wavelength Tx Power S e n s . Ref.Distance -T ST MMF 1310nm -19 ~ -14dBm -31dBm 2km -C SC MMF 1310nm -19 ~ -14dBm -31dBm 2km -JM MT-RJ MMF 1310nm -19 ~ -14dBm -31dBm 2km -VM VF-45 MMF 1310nm -20 ~ -14dBm -31dBm 2km -SA2...

Page 9 - Installing the Switch; Installation guide; Checking AC Power; AC power voltage of your area

- 9 - 2. Installing the Switch 2.1 Unpacking Check to see that you have everything before you start the installation.• Installation guide • The switch unit • One AC power adapter for the unit 2.2 Checking AC Power Before you begin the installation, check the AC voltage of your area. TheAC power adap...

Page 10 - Installing the Switch; Install the switch with the AC power adapter provided.

-10- The DC power jack for the AC power adapter is located on the rear of theswitch as shown below: 2.3 Installing the Switch 1. Install the switch with the AC power adapter provided. 2. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet.

Page 11 - Making Network Connections; The following figure shows the locations of the switched ports:; Making UTP Connections; All 10/100 TP ports support configuration as follows:

-11- 3. Making Network Connections 3.1 Switched Ports The following figure shows the locations of the switched ports: 3.2 Making UTP Connections 10/100 TP Port Configuration All 10/100 TP ports support configuration as follows: Auto-negotiation capableHighest capability : 100M Full duplexSpeed : aut...

Page 12 - Cables; Depending on the connection speed, use the proper UTP cables:; Speed; Making Fiber Connection; The following figure illustrates a connection example

-12- Cables Depending on the connection speed, use the proper UTP cables: Speed Cables used Distance 100M Cat. 5, 5e, or higher grade 100 meters 10M Cat. 3, 4, 5, 5e, or higher grade 100 meters Auto-MDI-X Function An Auto-MDI-X function will automatically detect if a crossover is re-quired and make ...

Page 13 - 00FX Duplex Selector; The following table lists the maximum; MM; fiber cable length connecting

-13- 100FX Duplex Selector This selector is used for 100FX port duplex mode selection as follows: The following table lists the maximum MM fiber cable length connecting to different devices: Connected Device Distance (MMF cable) Network card half-duplex fiber port 400 m Network card full-duplex fibe...

Page 14 - LED Functions; indicates the power status of the switch.; LED States and Indications; LED

-14- 4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing andmonitoring the operation of the switch as illustrated below: 4.2 Interpretation LED Functions POWER LED : indicates the power status of the switch. LNK/SPD/ACT LED : indicates the link status, con...