KTI Networks KG-500F - Manuals

Page 2 - from that to which the receiver is connected.

2 The information contained in this document is subject to changewithout prior notice. Copyright (C) All Rights Reserved. TRADEMARKS All brand names are trademarks or registered trademarks of theirrespective holders. Warning This equipment has been tested and found to comply with the limitsfor Class...

Page 3 - Marking by the symbol

3 CISPR 22 Class B This device complies with EMC directive of the European Commu-nity and meets or exceeds the following technical standard: EN 55022- Limits and Methods of Measurement of Radio Interference Char-acteristics of Information Technology Equipment. This device com-plies with CISPR 22 Cla...

Page 5 - M o d e l

5 Specifications Standards IEEE 802.3z 1000Base-SX/LX Network Port SFP for 1000Mbps mini-GBIC fiber transceiver Host Interface 32-bit 33/66Mhz PCI Rev.2.1/2.2/2.3 LEDs SFP status, Link status, Optical status Network Cables 50/125 multimode fiber up to 500m62.5/125 multimode fiber up to 220m9/125 sin...

Page 6 - Board Components; Adapter with PCI standard bracket

6 Board Components The figures show the major components on the adapters with PCIstandard bracket and PCI low-profile bracket. Adapter with PCI standard bracket

Page 7 - Adapter with PCI low-profile bracket; No. C o m p o n e n t s

7 Adapter with PCI low-profile bracket No. C o m p o n e n t s Description 1 LINK LED This LED lights when thefiber connection is established. 2 SFP LED This LED lights when a mini-GBICtransceiver module is installed inthe SFP slot. 3 OL LED This LED lights when optical signalis presented in the tra...

Page 8 - Installing the Adapter; Inserting the Adapter into the PCI Slot

8 Installing the Adapter Before installing the adapter, you need the following: • A computer system that is compliant with the PCI specifica- tions version 2.1 or later. • An available PCI bus master slot in the computer • The adapter driver diskettes (or CD supplied with the adapter) • Fiber cables...

Page 9 - Installing Mini-GBIC Transceiver; A typical mini-GBIC SFP transceiver is shown as follows:

9 Installing Mini-GBIC Transceiver A typical mini-GBIC SFP transceiver is shown as follows: To install a fiber transceiver into the SFP slot, the steps are: 1. Insert the fiber transceiver into the mini-GBIC SFP port. Normally, a bail is provided for every SFP transceiver. Hold thebail and make inse...

Page 10 - Connecting to the Network; The rear bracket of the PCI adapter contains two fiber connectors.

10 Connecting to the Network The rear bracket of the PCI adapter contains two fiber connectors. The TX connector is used for transmission and the RX is used forreception. When connecting to a device using fiber cable, make surethe TX connector of the adapter is connected to the RX connectorof the de...

Page 11 - Network Driver Installation; Installation for Windows Systems; After driver setup, the adapter is identified as :; Installation for other Systems

11 Network Driver Installation After making the connection to the network, you must install theadapter network driver in order to connect the network adapter toyour network operating system. The adapter driver media contain the latest versions of the networkdrivers available when the adapter is ship...

Page 12 - LED Indicators; The adapter has three LEDs. The interpretations of the LEDs are:; indicates an active 1000Mbps connection is established.; SFP LED; indicates installation status of mini-GBIC transceiver; OL LED; indicates optical signal status

12 LED Indicators The adapter has three LEDs. The interpretations of the LEDs are: LINK LED indicates an active 1000Mbps connection is established. On : Good link between the adapter and a remote device Off : No connection between adapter and a remote device Blink: Link on and traffic activities SFP...