KTI Networks KF-16M - Manuals

KTI Networks KF-16M – Manual in PDF format online.

Manuals:

Manual

Manual KTI Networks KF-16M

Summary

Ó 1998 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used tomake any directive work (such as translation or transformation) withoutpermission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documenta...

Page 3 - Installation Guide

16-port Dual-speedEthernet / Fast Ethernet Hub Installation Guide DOC.980302-KF16M/16MS-NK P/N: 750-0105-002

Page 4 - CE

The information contained in this document is subject to change without prior notice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant t...

Page 5 - Table of Contents

Table of Contents 1. Introduction ............................................................................... 1 1.1 Features .................................................................................................................. 2 1.2 Dual-speed Hub Technology ...........................

Page 6 - Figures

Figures 1-1 Dual-speed Ethernet / Fast Ethernet Hub Unit ...................................................... 1 1-2 Dual-speed Hub Design ......................................................................................... 3 1-3 Dual-speed Hub with Built-in 10/100 Switch ........................

Page 12 - Figure 2-1 Desktop Mounting

2. Installing the Dual-speed Hub The hub is designed to operate in workgroup environments without acomplicated configuration procedure. It also features an auto-select 100-240V, 50/60Hz power supply unit, which works in most countries aroundthe world. Before connecting the supplied power cord into t...

Page 14 - Front Panel and Rear Panel; Figure 2-4 Components on the Front and Rear Panel

2.3 Front Panel and Rear Panel Figure 2-4 Components on the Front and Rear Panel 8

Page 15 - This socket is used for plugging an AC power cord.; AC Power Switch

• 1X - 16X RJ-45 Connectors MDI-X jacks for Port #1 - Port #16 respectively • 16I RJ-45 Connector MDI-I jack for Port #16 • Diagnostic LED indicators The indicators provide the operating status of the hub and thenetwork ports. The status includes power, activity status for 10Msegment, activity statu...

Page 16 - Cascading Multiple Hubs; Figure 2-5 Cascading Two Hubs

2.4 Cascading Multiple Hubs More than one hub can be cascaded together to be a hub stack using thecascade cable supplied with the hub. Two cascade connectors are lo-cated on the rear of the hub and labeled IN and OUT respectively forKF-16M. For KF-16MS, only IN cascade connector is provided. Before ...

Page 18 - Making Network Connections; The pin definitions for MDI-X jack and MDI-I jack are as follows:; NC

3. Making Network Connections 3.1 Dual-speed Twisted-pair Ports Figure 3-1 16 Dual-speed TP Ports The hub provides 16 dual-speed TP ports. Each can support one con-nection to either a 10BASE-T Ethernet device or a 100BASE-TX FastEthernet device using 2-pair UTP cable. RJ-45 ConnectorsEach of Port #1...

Page 19 - Category 5 only; Figure 3-2 Straight-through UTP and Crossover UTP

UTP CablesFor connecting to an 10BASE-T Ethernet device, a 2-pair Category 3,4, or 5 UTP cable can be used. For connecting to a 100BASE-TX FastEthernet device, only 2-pair Category 5 UTP cable can be used. Connected Device UTP Cable Used 10BASE-T devices Category 3, 4 or 5 100BASE-TX devices Categor...

Page 20 - Figure 3-3 Connecting to Computers

Connecting to a ComputerThe RJ-45 connectors labeled 1X to 16X can be used for connecting tothe network adapter installed in a computer. The network adapter can bea 10BASE-T adapter, a 100BASE-TX adapter, or a dual-speed NWayadapter. The following figure illustrates the cables used for connectingto ...

Page 21 - Note: only one Class II hub connection is allowed per hub.; Figure 3-5 Connecting to a 100BASE-TX Class II Hub; Switch Connected; 00BASE-TX switch port

Connecting to a 100BASE-TX HubSince the KF-16M and KF-16MS hubs are designed to comply withIEEE 802.3u Class II repeater specifications, each hub can support oneconnection to another 100BASE-TX Class II hub only. It is recommendedto preserve Port #16 as a uplink port for connecting to another hub (o...

Page 22 - Hub Stack Connection; Figure 3-6 Connecting Two Hub Stacks

3.2 Hub Stack Connection A hub stack composed of multiple hubs (up to four) cascaded togetheras the instruction in section 2.4 can be treated as a single dual-speed hubwhich provides up to 64 dual-speed ports. If interconnection of the 10M network and the 100M network is re-quired, one and only one ...