Kramer TP-202 - Manuals - manualsarea.com

Page 3 - Contents; Introduction; Figures

TP-202 – Contents i Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 3 2.3 Recycling Kramer Products 3 3 Overview 4 3.1 About the Power Connect™ Feature 4 3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) 5 3.3 Defining the TP-2...

Page 4 - Congratulations on purchasing your Kramer

TP-202 - Introduction 1 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis. In re...

Page 5 - Getting Started; Achieving the Best Performance

2 TP-202 - Getting Started 2 Getting Started We recommend that you:  Unpack the equipment carefully and save the original box and packaging materials for possible future shipment  Review the contents of this user manual Go to http://www.kramerelectronics.com to check for up-to-date user manuals, a...

Page 6 - Safety Instructions; There are no operator serviceable parts inside the unit; Recycling Kramer Products; go to our recycling pages at

TP-202 - Getting Started 3 2.2 Safety Instructions Caution: There are no operator serviceable parts inside the unit Warning: Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning: Disconnect the power and unplug the unit from the wall before installing 2.3 R...

Page 7 - Overview; UXGA Line Transceiver/DA; About the Power

4 TP-202 - Overview 3 Overview The TP-202 is a twisted pair branching receiver for computer graphics video signals with resolutions from VGA up to UXGA and higher or HDTV signals. It takes a twisted pair signal and converts it into a computer graphics video signal or HDTV signal available on two 15-...

Page 8 - Defining the TP-202 UXGA Line Transceiver/DA; This section defines the

TP-202 - Overview 5 3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) We recommend that you use Shielded Twisted Pair (STP) cable, and stress that the compliance to electromagnetic interference was tested using STP cable. There are different levels of STP cable available, and we advise...

Page 9 - Figure 2

6 TP-202 - Overview # Feature Function 1 EQ. Trimmer Adjust the cable compensation equalization level Insert a screwdriver into the small hole and carefully rotate it, to trim the appropriate level 2 LEVEL Trimmer Adjust the output signal level 3 UXGA OUT 1 15-pin HD Connector Connect to the first U...

Page 10 - Connecting the TP-202; the LINE OUT

TP-202 - Connecting the TP-202 7 4 Connecting the TP-202 Always switch off the power to each device before connecting it to your TP-202 . After connecting your TP-202 , connect its power and then switch on the power to each device. You can use the TP-202 UXGA Line Transceiver/DA to configure a UXGA ...

Page 12 - Wiring the TP LINE IN / LINE OUT RJ-45 Connectors; This section defines the TP pinout, using a; straight

TP-202 - Connecting the TP-202 9 4.1 Wiring the TP LINE IN / LINE OUT RJ-45 Connectors This section defines the TP pinout, using a straight pin-to-pin cable with RJ-45 connectors. Note, that the cable Ground shielding must be connected / soldered to the connector shield. EIA /TIA 568B Figure 4: TP P...

Page 13 - Technical Specifications

10 TP-202 - Technical Specifications 5 Technical Specifications INPUT: 1 CAT 5 LINE IN on an RJ-45 connector OUTPUTS: 1 CAT 5 LINE OUT on an RJ-45 connector 2 UXGA on 15-pin HD connectors MAX. OUTPUT LEVEL: 1.5Vpp RESOLUTION: Up to UXGA, up to 1080p DIFF. GAIN: 2.8% DIFF. PHASE: 0.2Deg K-FACTOR: 0.1...