Konica Minolta C6500 - Manuals

1 Introduction 1-4 bizhub PRO C6500 / bizhub PRO C6500e 1.1 Safety instructions For your safe operation, the following are the descriptions of the notices and requests that you have to follow when replacing parts. Be sure to read them carefully before conducting any part replacement operation. - Be ...

Introduction 1 bizhub PRO C6500 / bizhub PRO C6500e 1-5 Operations before replacing any part 7 CAUTION Ignoring this cautions could cause injury or damage to property. % Do not ignore these safety advices. CMS part replacement operation 7 WARNING Ignoring this warnings could cause serious injury or ...

1 Introduction 1-6 bizhub PRO C6500 / bizhub PRO C6500e Power plug 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. 7 CAUTION Ignoring this cautions could cause injury or damage to property. % Do not ignore these safety advices. Warning...

Introduction 1 bizhub PRO C6500 / bizhub PRO C6500e 1-7 When any abnormal condition is found 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. 7 CAUTION Ignoring this cautions could cause injury or damage to property. % Do not ignore the...

1 Introduction 1-8 bizhub PRO C6500 / bizhub PRO C6500e 1.2 Caution notations and caution labels For this copier, there are the caution notations or labels for safety operations provided at the locations as shown below. Be sure to take every care to avoid any accidents while in the part replacement ...

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-3 2 bizhub PRO C6500/bizhub PRO C6500e 2.1 Maintenance procedure of the housing section Removing the dust-proof filter 1 assy Periodically replaced parts/cycle: - Dust-proof filter 1 assy: Every 200,000 prints (actual replac...

2 bizhub PRO C6500/bizhub PRO C6500e 2-4 bizhub PRO C6500 / bizhub PRO C6500e 4 Remove the screw, and remove the filter cover. 5 Remove the dust-proof filter 1 assy. Reinstalling the dust-proof filter 1 assy % Reinstall the above parts following the removal steps in reverse. screw filter cover dust-...

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-5 Removing the dust-proof filter 2 assy Periodically replaced parts/cycle: - Dust-proof filter 2 assy: Every 200,000 prints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn OFF the main power switch...

2 bizhub PRO C6500/bizhub PRO C6500e 2-6 bizhub PRO C6500 / bizhub PRO C6500e 4 Loosen the two screws and remove the filter cover. 5 Pull out the dust-proof filter 2 assy from the filter cover. Reinstalling the dust-proof filter 2 assy % Reinstall the above parts following the removal steps in rever...

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-7 2.2 Maintenance procedure of the toner collection box Removing the toner collection box assy Periodically replaced parts/cycle: - Toner collection box assy: Every 50,000 prints 1 Turn OFF the sub power switch. 2 Open the l...

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-9 5 Peel off the label on the toner collection box assy and close the opening of the toner collection box assy with the label. Reinstalling the toner collection box assy % Reinstall the above parts following the removal step...

2 bizhub PRO C6500/bizhub PRO C6500e 2-10 bizhub PRO C6500 / bizhub PRO C6500e 2.3 Maintenance procedure of the paper feeding section Removing the pick-up roller/paper feed roller rubber Periodically replaced parts/cycle: - Pick-up roller: Every 2,400,000 prints (actual replacement cycle: every 800,...

2 bizhub PRO C6500/bizhub PRO C6500e 2-14 bizhub PRO C6500 / bizhub PRO C6500e 10 Remove the bearing. 11 Remove the C-clip 1 and remove the pick-up roller. – When installing the pick-up roller, be sure that the arrow mark 1 is facing toward the C-clip 1. 12 Remove the C-clip 2 and remove the paper f...

2 bizhub PRO C6500/bizhub PRO C6500e 2-16 bizhub PRO C6500 / bizhub PRO C6500e 4 Remove the paper feed roller assy. For details, refer to "Removing the pick-up roller/paper feed roller rubber" on page 2-10. 5 Remove the C-clip and remove the separation roller. – Before installing the separat...

2 bizhub PRO C6500/bizhub PRO C6500e 2-18 bizhub PRO C6500 / bizhub PRO C6500e 4 While lifting the lever marked in the picture, turn the handle in the arrow marked direction and pull out the ADU. 5 Remove the six screws and remove the paper feed solenoid cover. lever screws paper feed solenoid cover...

2 bizhub PRO C6500/bizhub PRO C6500e 2-20 bizhub PRO C6500 / bizhub PRO C6500e 7 Remove the bearing and remove the paper feed roller unit. – When installing the paper feed roller unit, be sure to fit the actuator in the detection section of the paper empty sensor/BP (PS47). – When installing the pap...

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-21 9 Remove the pick-up roller from the pick-up roller assy. 10 Remove the paper feed roller assy from the shaft. 11 Remove the paper feed roller rubber from the paper feed roller assy. – When installing the paper feed rolle...

2 bizhub PRO C6500/bizhub PRO C6500e 2-22 bizhub PRO C6500 / bizhub PRO C6500e 2.5 Maintenance procedure of the fusing section 7 CAUTION Precaution for high temperature Immediately after turning off the main power switch or the sub power switch, the fusing section is very hot and you may get burnt. ...

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-23 4 While lifting the lever marked in the picture, turn the handle in the arrow marked direction and pull out the ADU. 5 Open the front door and the toner supply section. lever

bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-25 8 Remove the screw, and remove the knob. 9 Remove the two screws and remove the front fusing cover. screw screws knob front fusing cover

2 bizhub PRO C6500/bizhub PRO C6500e 2-26 bizhub PRO C6500 / bizhub PRO C6500e 10 Disconnect the two connectors. 11 Open the reverse/exit section. 12 Remove the screw and remove the fusing unit. – When installing/removing the fusing unit, be sure to hold both ends of the unit and slide it toward you...

PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-3 3 PF-601/HT504 3.1 Maintenance procedure of the tray section Removing the pick-up rubber/paper feed roller Periodically replaced parts/cycle: - Pick-up rubber: Every 600,000 prints (actual replacement cycle: every 300,000 feed) - Paper feed rol...

3 PF-601/HT504 3-6 bizhub PRO C6500 / bizhub PRO C6500e 7 Rotate the pick-up roller in the direction of the arrow (clockwise as seen from the front side) and bring the coupling to the shown position. – Be sure not to rotate the pick-up roller against the direction of the arrow forcibly, as the rolle...

PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-7 10 Move the rear bearing to the rear side. – When installing the bearing, hold down the metal plate of the pick-up roller assy slightly, and insert the flat part of the rear bearing while keeping it horizontally into the notch of the metal plat...

3 PF-601/HT504 3-10 bizhub PRO C6500 / bizhub PRO C6500e 19 Remove the C-clip and pull out the paper feed roller from the collar. 20 Replace the paper feed roller. – The appearance of the collars is the same for the paper feed roller and the separation roller. However, the collar of the paper feed r...

PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-11 Removing separation roller Periodically replaced parts/cycle - Separation roller: Every 600,000 prints (actual replacement cycle: every 300,000 feed) 2 Note The appearance of the collars is the same for the paper feed roller and the separation...

3 PF-601/HT504 3-16 bizhub PRO C6500 / bizhub PRO C6500e Reinstalling the separation roller % Reinstall the above parts following the removal steps in reverse.

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-3 4 DF-609 4.1 Maintenance procedure of the paper feeding section Removing the paper feed unit 1 Turn OFF the sub power switch. 2 Open the left front door, and then trun OFF the main power switch. 3 Unplug the power cord. left front door main power swi...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-5 7 Remove the screw and remove the shaft securing plate. 8 Remove the two C-clips. screw shaft securing plate C-clip bearing paper feed unit C-clip bearing

4 DF-609 4-6 bizhub PRO C6500 / bizhub PRO C6500e 9 Slide the two bearings inward, and remove the paper feed unit. – When removing the paper feed unit, be sure not to damage the arm with the shaft. – When installing the paper feed unit, make sure the arm is mounted on the shaft. – When installing th...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-7 Removing the pick-up roller/paper feed roller Periodically replaced parts/cycle - Paper feed roller: Every 1,800,000 prints (actual replacement cycle: every 625,000 feed) - Pick-up roller: Every 1,800,000 prints (actual replacement cycle: every 625,0...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-9 8 Remove the C-clip, then remove the gear and the pin. – Be careful not to lose the pin as it may drop off the shaft when removing the gear. 9 Remove the arm and the pin. – Be careful not to lose the pin as it may drop off the shaft when removing the...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-11 13 Remove the pin and remove the pick-up roller. 14 Remove the C-clip. – Be careful not to lose the pin as it may drop off the shaft when removing the C-clip. 15 Remove the pin and remove the pick-up roller. Reinstalling the pick-up roller/paper fee...

4 DF-609 4-12 bizhub PRO C6500 / bizhub PRO C6500e Removing the separation roller Periodically replaced parts/cycle - Separation roller: Every 1,800,000 prints (actual replacement cycle: every 625,000 feed) 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn OFF the main power...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-13 4 Open the paper feed cover. 5 Push the two tabs inward to release the lock and remove the separation unit cover. tabs paper feed cover tabs

4 DF-609 4-14 bizhub PRO C6500 / bizhub PRO C6500e 6 Pinch both ends of the roller shaft and raise the separation roller straight up. 7 Remove the separation unit and replace it with a new one. Reinstalling the pick-up roller/paper feed roller % Reinstall the above parts following the removal steps ...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-17 Removing the registration roller cover 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn OFF the main power switch. 3 Unplug the power cord. left front door main power switch sub power switch

4 DF-609 4-18 bizhub PRO C6500 / bizhub PRO C6500e 4 Open the paper feed cover. 5 Raise the paper feed tray straight up. 6 Remove the four screws and remove the registration roller cover. Reinstalling the registration roller cover % Reinstall the above parts following the removal steps in reverse. p...

DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-19 Cleaning the registration roller Periodically cleaned parts/cycle: - Registration roller: Every 200,000 prints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn OFF the main power switch. 3 Unplug the power cord. left front ...

Appendix 5 bizhub PRO C6500 / bizhub PRO C6500e 5-3 5 Appendix 5.1 Replacement parts list Main body Part name Part number Toner collection box A03UR7020 Dust-proof filter 1 (right side) exchanging assy A03UR7010 Dust-proof filter 2 (rear side) 65AAR7180 Feed / reverse (separation) rubber (tray 1) 25...

5 Appendix 5-4 bizhub PRO C6500 / bizhub PRO C6500e Paper feeding unit PF-601 Document feeder DF-609 Part name Part number Pick-up rubber 55VA4111 Paper feed roller 55VA-483 Separation roller 55VA-483 Part name Part number Pick-up roller 13YH4039 Paper feed roller 13YH4064 Separation roller 20AJ4015