Kodak 3H0610 - Manuals

Contents July 1998 vii I N T RODUC T I ON 9.3 Contents of NIC/Macintosh Utilities Diskette ............................................................. 9-3 9.3.1 Using the Laserwriter Utility for Downloading Configuration Files ............... 9-4 9.4 Configuring Macintosh Systems for Printing .......

Contents viii July 1998 I N T RODUC T I ON 11.7 Printing from UNIX System V Systems .................................................................... 11-6 11.8 Printing from VMS Systems ...................................................................................... 11-7 11.8.1 Printing in ...

Kodak 10/100 NIC Introduction and Configuration July 1998 1-1 I N T RODUC T I ON 1 Kodak 10/100 NIC Introduction and ConÞguration 1.1 About this Guide This guide provides information about the Kodak 10/100 Network Interface Card (NIC) features, installation and conÞguration. This NIC can be used wit...

Kodak 10/100 NIC Introduction and Configuration 1-2 July 1998 I N T RODUC T I ON It is also intended for administrators and experienced users responsible for conÞguring individual workstation platforms. This guide assumes an understanding of Novell IPX, EtherTalk, TCP/IP, and/or NetBeui networking p...

Kodak 10/100 NIC Introduction and Configuration July 1998 1-3 I N T RODUC T I ON Chapter 10 - Unix Chapter 11 - Network Printing: Summarizes techniques for printing from Windows, Macintosh and Unix platforms. Chapter 12 - TroubleShooting: Provides ßow charts and speciÞcs on various steps. Appendix A...

Kodak 10/100 NIC Introduction and Configuration 1-4 July 1998 I N T RODUC T I ON 1.5 Upgrading from a Kodak 10Mbit NIC The Kodak 10/100 Mbit NIC may be used to upgrade any Kodak printers that are currently using a Kodak 10Mbit NIC with a ÒMIL-3007EKÒsticker on the bottom of the NIC. Note: This manua...

Kodak 10/100 NIC Introduction and Configuration July 1998 1-5 I N T RODUC T I ON 1.7 Protocols ¥ The NIC supports TCP/IP, Novell IPX, EtherTalk and NetBeui/NetBios protocols. ¥ Users can print in either PostScript or raster mode. IMPORTANT: Printing in raster mode using EtherTalk is possible only fr...

Kodak 10/100 NIC Introduction and Configuration 1-6 July 1998 I N T RODUC T I ON Step 1:Determine your Network and Printing Environment. (Ch1:Intro/Overview)NIC supports TCP/IP, Novell Netware, AppleTalk & Native Windows (NetBeui) Protocols. Step 2: Gather Necessary Hardware & Software Compo...

Kodak 10/100 NIC Introduction and Configuration July 1998 1-7 I N T RODUC T I ON Step 1: Assess your network/printing environment Consult with your system/network administrator regarding ¥ Protocols: Determine the network protocol(s) (TCP/IP, Novell IPX, AppleTalk and/or NetBIOS) to use for communic...

Kodak 10/100 NIC Introduction and Configuration 1-8 July 1998 I N T RODUC T I ON ¥ Windows & Macintosh Printer ConÞguration Software: PostScript drivers for Kodak printers for printing when the printer is in PostScript mode and Export modules for printing when the printer is in raster mode. For ...

Kodak 10/100 NIC Introduction and Configuration July 1998 1-9 I N T RODUC T I ON NIC ConÞguration Software ¥ Windows : The NIC may be conÞgured from Windows-based platforms using NIC FastManage, NBMon or Telnet utilities. Refer to the Windows FastManage Utility chapter. ¥ Macintosh : The NIC may be ...

Kodak 10/100 NIC Introduction and Configuration 1-10 July 1998 I N T RODUC T I ON Raster mode: Printer drivers (referred to as Export Modules) must be installed on each platform that prints (exports) Þles to the printer. Export modules are used with Adobe PhotoShop and with the Kodak Printer Calibra...

NIC Installation and Verification July 1998 2-1 I NS T A LL A T I ON 2 NIC Installation and Verification This chapter describes how to install the NIC in the Kodak XLS 8400 and 8600 printers, the Kodak Digital Science 8650 printer, the Kodak Professional 8657 printer, the Kodak Digital Science Deskt...

NIC Installation and Verification 2-2 July 1998 I NS T A LL A T I ON 2. Attach the wrist portion of the antistatic strap to your wrist. Attach the other end of the strap to the metal plate on the back of the printer. CAUTION: Wear the antistatic strap when you open the back of the printer, remove th...

NIC Installation and Verification 2-4 July 1998 I NS T A LL A T I ON 2. Attach the wrist portion of the antistatic strap to your wrist. Attach the other end of the strap to the metal plate on the electronics drawer on the proofer. CAUTION: Wear the antistatic strap when you remove the electronics dr...

NIC Installation and Verification July 1998 2-5 I NS T A LL A T I ON 2. Hold the card so that the printer connector is facing down and the network cable receptacle is toward you. 3. Tilt the card at about a 30-degree angle, and slide the front into the NIC slot. Seat the card by positioning the conn...

NIC Installation and Verification 2-6 July 1998 I NS T A LL A T I ON The green Link LED should come ON and remain ON until the printer reaches READY . The yellow Net Traffic should blink 3 to 4 times a second until the printer reaches READY . This process may occur twice; the NIC will start a power ...

NIC Installation and Verification July 1998 2-7 I NS T A LL A T I ON 2.6 NIC Faceplate The illustration below shows the NIC faceplate (as seen from the rear of the printer after installation). Switches: D1 and D2 are operation mode switches; they are shown in Normal Operation Mode for printing (D1 &...

NIC Installation and Verification 2-8 July 1998 I NS T A LL A T I ON Power cycle the device whenever you reset the switches. When finished in any mode, return the switches to Normal or Telnet mode, then power cycle the device again for printing. 2.8 Configuring the Network Parameters If you will be ...

Windows - FastManage Configuration Utilities July 1998 3-1 F AS T MANAGE 3 Windows - FastManage ConÞguration Utilities Windows FastManage Utilities: FastManage Utilities allow you to conÞgure the NIC remotely from Windows platforms. They provide complete control over all network protocols and relate...

Windows - FastManage Configuration Utilities 3-2 July 1998 F AS T MANAGE 3.1.1 FastManage Hardware Requirements FastManage requires: ¥ A 486 Pentium PC, 66 Mhz computer or higher ¥ 16 MB of RAM or higher ¥ At least 4 MB of free disk space ¥ Microsoft Windows 3.1 or higher ¥ Ethernet card installed F...

Windows - FastManage Configuration Utilities July 1998 3-3 F AS T MANAGE 3.2 Extracting Files from the Windows Utilities Diskette The NIC.exe Þle on the diskette is a compressed archive of DOS/ Windows for conÞguring the NIC networking parameters. To effectively manage these Þles, do as follows: 1. ...

Windows - FastManage Configuration Utilities 3-4 July 1998 F AS T MANAGE 3.3 Installing FastManage To install FastManage on MS windows: 1. Select Run from the File menu. 2. Type c:\Kodak\Fast\setup.exe on the command line and click OK . The FastManage Welcome screen appears. 3. Register FastManage a...

Windows - FastManage Configuration Utilities July 1998 3-5 F AS T MANAGE Note: IPX support requires that DOS and Windows drivers for Novell already be installed. If you selected IP, continue to the next step. Otherwise, jump to step 7. 6. (If you selected IP) Specify the local workstationÕs IP addre...

Windows - FastManage Configuration Utilities 3-6 July 1998 F AS T MANAGE ¥ If the IPX protocol is loaded and running on a system running Windows 95, the check box for Send NetBIOS over IPX should not be checked. Send NetBIOS over IPX is located in the Control Panel --> Network --> IPX Compatib...

Windows - FastManage Configuration Utilities July 1998 3-7 F AS T MANAGE Once the system is operational, the FastManage screen appears. 3.4 FastManage - Discovery Application The Discovery application detects network SNMP manageable devices on IP, IPX, and NetBEUI (NetBIOS) networks. On IP networks,...

Windows - FastManage Configuration Utilities 3-8 July 1998 F AS T MANAGE Discovery supports a limited amount of placement so that you can position the device on the ÒmapÓ most suited to your needs. You can also make devices that you do not want to manage invisible, store a map, or restore an old map...

Windows - FastManage Configuration Utilities July 1998 3-9 F AS T MANAGE To open the Discovery Application , double-click on the icon. A Discovery Map appears with all detected devices. If, during installation, you chose more than one protocol to Þnd SNMP devices, an icon will be displayed for each ...

Windows - FastManage Configuration Utilities 3-10 July 1998 F AS T MANAGE Click twice on a Kodak Printer/Proofer icon to start up the NIC Manager for conÞguring a Kodak Printer/Proofer 10/100 Network Interface Card. 3.4.2 Kodak Printer/Proofer NIC Icon Names In the Discovery map, the following icon ...

Windows - FastManage Configuration Utilities July 1998 3-11 F AS T MANAGE ¥ SNMPAxxxxxx ÑThis device was discovered by the SNMP over NetBIOS (where xxxxxx are the last six digits of the Ethernet address. For example, a device with an Ethernet address of Ò0040C00702CA,Ó will have a NetBIOS name of Kd...

Windows - FastManage Configuration Utilities 3-12 July 1998 F AS T MANAGE 2. Delete the old name and enter a new Map name. 3. Click OK . 3.4.3.2 Changing from the Node Name to an Address You can display either the name or address of a device. To change from a name to the address, click the Node/Addr...

Windows - FastManage Configuration Utilities July 1998 3-13 F AS T MANAGE 2. Type the Þle name in the Download File Name Þeld, or click Browse to search for the Þles. 3. Enter the IP address of the device to which you are downloading, then click Download to download the Þle. Note: The download proce...

Windows - FastManage Configuration Utilities 3-16 July 1998 F AS T MANAGE 3.4.4.5 Protocols ¥ Enable IP, Enable IPX, Enable NetBIOS - after installation, Discovery protocols may be selected and de-selected using this menu. Note: If you disable all protocols and then close Discovery, Discovery will n...

Windows - FastManage Configuration Utilities July 1998 3-19 F AS T MANAGE 1. Fill in the required parameters: ÒGet CommunityÓ and ÒSet CommunityÓ are the only required parameters. By default, Get Community is set to public ; and Set Community is set to private . The parameters ÒDescription,Ó ÒName,Ó...

Windows - FastManage Configuration Utilities 3-20 July 1998 F AS T MANAGE 3.5 Fastmanage - Kodak NIC Manager Application Use the Kodak NIC Manager to conÞgure the NIC relative to the various network protocols. After FastManage installation is complete, a Kodak FastManage window should appear (shown ...

Windows - FastManage Configuration Utilities July 1998 3-21 F AS T MANAGE A graphic displaying the NIC faceplate appears. This graphic is the same as displayed during the Discovery Application when you double click the Kodak Printer/Proofer NIC icon. Hot Spots on the graphic lets you obtain informat...

Windows - FastManage Configuration Utilities 3-22 July 1998 F AS T MANAGE 3.6.1 TCP/IP Configuration You make a series of choices to conÞgure the NIC on TCP/IP networks. Below is a hierarchy of these choices. From TCP/IP ConÞde. , selections include: IP ConÞguration --> ¥ IP Address : Allows you ...

Windows - FastManage Configuration Utilities July 1998 3-23 F AS T MANAGE Restricted Hosts --> ¥ Subnets : Limits access to FastManage. Only hosts in the selected subnet can access FastManage. ¥ Allowed IP Addresses : Limits access to FastManage. Only hosts with IP addresses can access FastManage...

Windows - FastManage Configuration Utilities 3-24 July 1998 F AS T MANAGE NDS ConÞguration --> ¥ Enable NDS : Enables/disables NetWare directory services. ¥ Preferred DS Tree : Sets the ÒtreeÓ where the print server and print queues are deÞned. ¥ Preferred DS Context : Sets the ÒcontextÓ where th...

Windows - FastManage Configuration Utilities 3-26 July 1998 F AS T MANAGE 3.7.2 SMB Configuration The choices you can make to conÞgure the printer/NIC for a SMB network are shown and described below. SMB ConÞg options include: ¥ SMB ConÞg. --> ¥ HP DLC: Enables/disables HP DLC protocol ¥ SMB Enab...

Windows - FastManage Configuration Utilities July 1998 3-27 F AS T MANAGE 3.7.4 Status Menu These parameters currently have no function. 3.7.5 Help Menu The Help menu has two options, ÒUsing HelpÓ and ÒAbout Kodak NIC Manager.Ó ¥ Using Help : A standard Windows help Þle appears. ¥ About Kodak NIC Ma...

Windows - FastManage Configuration Utilities July 1998 3-29 F AS T MANAGE 3.9 FastManage - BOOTP Application TheBOOTP application implements a BOOTP server and allows you to assign IP addresses dynamically to network devices. FastManage network print servers implement BOOTP and can obtain their IP a...

Windows - FastManage Configuration Utilities July 1998 3-31 F AS T MANAGE 3.10 NetBeui Browsing and Sharing Abilities When a client machine comes up on the network, it usually comes up in a pre-conÞgured workgroup. The default workgroup for all NetBIOS machines (including the Kodak NIC) is named Wor...

Windows - FastManage Configuration Utilities 3-32 July 1998 F AS T MANAGE 3. Enter net? at a DOS prompt for more information about the utilities. 3.10.1 DOS Tools for NetBIOS If you have problems installing and using the NetBIOS management tools, the following suggestions might help: ¥ When using th...

Windows - FastManage Configuration Utilities July 1998 3-33 F AS T MANAGE 3.11 Troubleshooting FastManage The following table lists problems that may occur with FastManage; it also lists possible solutions. 3.11.1 Error Messages The following table contains error messages that you may see while usin...

Windows - FastManage Configuration Utilities 3-36 July 1998 F AS T MANAGE 3.11.5 BOOTP Server Application Messages The following messages may appear while you are using the BOOTP Server Application. BOOTP Server Application Messages Problem Cause Solution Please retry when there is a bootptab Þle No...

Novell NetWare July 1998 4-1 NOVE LL NE T WARE 4 Novell NetWare Refer to Kodak Printer/NIC Installation and ConÞguration Overview in Chapter 1 for overall conÞguration process steps and details. This chapter describes the conÞguration of Novell Netware print servers and queues. 4.1 NetWare Client In...

Novell NetWare 4-2 July 1998 NOVE LL NE T WARE 5. Set up the preferred server name on the NIC, using NIC conÞguration utilities for Windows. Note: For more information on setting the preferred server name, see Chapter 3, Windows - FastManage ConÞguration Utilities . 4.3 ConÞguring in an NDS Environm...

Novell NetWare 4-6 July 1998 NOVE LL NE T WARE 4.3.4.3 Connecting the Print Server to a Printer 1. In the Context Tree window, double-click the print server created. 2. Click Assignments in the following window. 3. In the next window, click Add . 4. Highlight the printer created and click OK . The s...

Novell NetWare July 1998 4-7 NOVE LL NE T WARE 4.3.4.4 Assigning a Print Queue to a Print Server 1. Double-click the recently assigned printer. 2. In the window that appears, click Assignments . 3. In the Assignments window, click Add . 4. In the Select Object window, select the print queue created ...

Novell NetWare 4-8 July 1998 NOVE LL NE T WARE ¥ When logged in to an NDS environment as an NDS Print Server, you should conÞgure the print server with only one NDS Printer object. You specify parameters, such as which port to send data (LPT or COM) by creating special queue name sufÞxes. The major ...

Novell NetWare July 1998 4-9 NOVE LL NE T WARE 6. Once it locates a Bindery Þle server, the NIC looks in its preferred server for an NVRAM value, and if a value exists, routes itself to that server. 7. The NIC then looks on the preferred server for a print server queue in the form of KDxxxxxx. 8. Th...

Novell NetWare 4-10 July 1998 NOVE LL NE T WARE 2. On the server, back up the sys:\system\atps.cfg Þle. Note: Make sure you include the beginning and end quotes in the following commands. Edit the atps.cfg Þle, and add a line with the Kodak printer AppleTalk name and its associated AppleTalk zone to...

Novell NetWare July 1998 4-11 NOVE LL NE T WARE 4.6 Troubleshooting Netware The printer/NIC does not log in to bindery Novell 3.x server The server may not have the bindery emulation mode enabled. To verify that the bindery emulation is enabled, Þnd the following line in the autoexec.ncf Þle in the ...

Windows for WorkGroups (3.x) July 1998 5-1 W I ND O W S 3 X 5 Windows for WorkGroups (3.x) Refer to Kodak Printer/NIC Installation and ConÞguration Overview in Chapter 1 for overall conÞguration process steps and details. In the list below, the steps described in this chapter are highlighted. Step 1...

Windows 95 6-2 July 1998 W I ND O W S 95 Adding a Printer to Your System Use the following procedure to add a printer, install a PostScript driver, and select a server print queue to use for printing. If problems occur, refer to the Windows 95 documentation, README FIles, and software provided with ...

Windows 95 July 1998 6-3 W I ND O W S 95 6.2.2 Using the ÒAdd PrinterÓ Method 1. From the Start icon, select Settings and then Printers . 2. Click on the Add Printer icon. 3. Click on Next .

Windows 95 July 1998 6-5 W I ND O W S 95 7. If you are installing the printer driver from a diskette or a CD-ROM , insert the proper media, then click on OK . If installation software has been copied to your system , click on Browse to locate the directory where it resides. When the correct director...

Windows 95 July 1998 6-7 W I ND O W S 95 12. Click on Yes to print a test page to verify that the setup is correct. Click on Finish . Note: If errors occur when you print a test page, check the Printer Properties menus for the correct printer parameter settings. Refer to Section 6.2.3, Setting Print...

Windows 95 July 1998 6-9 W I ND O W S 95 ÑSelect PostScript > Advanced , then make sure that all Ctrl D s before and after jobs are disabled. This prevents you from receiving extra pages or a blank PostScript error page. ÑCheck Capture Settings; to eliminate extraneous banner (USER ID) pages, mak...

Windows NT 3.51Workstation/Servers July 1998 7-1 W I ND O W S N T 351 7 Windows NT 3.51Workstation/Servers Refer to Kodak Printer/NIC Installation and ConÞguration Overview in Chapter 1 for overall conÞguration process steps and details. Steps covered in this chapter are highlighted in the list belo...

Windows NT 3.51Workstation/Servers July 1998 7-3 W I ND O W S N T 351 7.3 ConÞguring your Workstation for Printing You should verify that this platform is supported for printing to your printer or proofer. Refer to User Guides and software README Þles provided with your printer or proofer for inform...

Windows NT 3.51Workstation/Servers July 1998 7-7 W I ND O W S N T 351 Note: If AppleTalk Printing Devices Port is not in the menu, select Other again and install AppleTalk Protocol. 3. Double-click on the pertinent AppleTalk Zone to view the available devices and to select the Kodak printer.. IMPORT...

Windows NT 3.51Workstation/Servers July 1998 7-9 W I ND O W S N T 351 3. Enter the name of the Windows NT server for which the printer is conÞgured. Note: In the example above, Location = NALA and Share name = DS8650 results in a \\ NALA \ DS8650 server/queue that is available for users to select fr...

Windows NT 4.0 Workstation/Servers July 1998 8-1 W I ND O W S N T 40 8 Windows NT 4.0 Workstation/Servers Refer to Kodak Printer/NIC Installation and ConÞguration Overview in Chapter 1 for overall conÞguration process steps and details. In the list below, the steps described in this chapter are high...

Windows NT 4.0 Workstation/Servers July 1998 8-3 W I ND O W S N T 40 8.4 Printer/NIC selection and printer setup using Win 95/NT Network Neighborhood: If you have network browsing capabilities and you select Workgroup , you should be able to see the printer/NIC advertising itself as KDxxxxxx , where...

Windows NT 4.0 Workstation/Servers 8-4 July 1998 W I ND O W S N T 40 The Printers window appears. 2. Click on Add Printer. The Add Printer Wizard window appears. 3. Select My Computer , then click on Next . 4. From the Add Printer Wizard screen, do one of the following: If you are conÞguring your se...

Windows NT 4.0 Workstation/Servers July 1998 8-7 W I ND O W S N T 40 The Printer Ports window appears. 5. Select AppleTalk Printing Devices . Note: If AppleTalk Printing Devices option is not available, install AppleTalk Protocol. The AppleTalk Printing Devices window appears. 6. Double-click on you...

Windows NT 4.0 Workstation/Servers July 1998 8-9 W I ND O W S N T 40 5. Enter the name of the print queue. For example: Server = NT Svr and Share name = KodakQ would result in \\NTSvr\KodakQ being the name of the queue. The procedure is complete. Proceed to Section 8.6, Installing the Kodak Printer ...

Windows NT 4.0 Workstation/Servers 8-12 July 1998 W I ND O W S N T 40 You are prompted whether to print a test page. 8. Click on Yes and then on Finish . Note: If errors appear on the printer display panel (load paper, ribbon) when a test page is generated, check the Printer Properties menus for cor...

Windows NT 4.0 Workstation/Servers July 1998 8-13 W I ND O W S N T 40 8.7 Printer Properties To avoid printing errors, set up the appropriate printer properties. 1. From the Printers window, select the Kodak printer you conÞgured. 2. Select Properties from the File menu. The following window appears...

Apple/Macintosh Environments July 1998 9-1 M AC I N T O S H 9 Apple/Macintosh Environments Refer to Kodak Printer/NIC Installation and Configuration Overview in Chapter 1 for information about the overall configuration process. Steps covered in this chapter are highlighted in the list below. Step 1:...

Apple/Macintosh Environments 9-2 July 1998 M AC I N T O S H 9.1 Kodak 10/100 NIC - Utilities for Macintosh Use the Kodak 10/100 NIC - Utilities for Macintosh software to remotely configure the parameters for the 10/100 NIC installed in Kodak printers or proofers. IMPORTANT: Configuration for this 10...

Apple/Macintosh Environments 9-4 July 1998 M AC I N T O S H • NIC Config—provides a configuration file with default NIC parameters. To change network parameters listed in the file, copy the file, edit it, then download it to the NIC using the Apple Printer Utility. Instructions are included in the N...

Apple/Macintosh Environments July 1998 9-5 M AC I N T O S H 9.4.3 Default AppleTalk/EtherTalk Parameters Parameter change methods listed here presume the use of Utilities for Macintosh. IMPORTANT: Verify that the printers are operating properly on your network using the default parameters before you...

Apple/Macintosh Environments 9-6 July 1998 M AC I N T O S H When the NIC Configuration Test Print is complete, set the switches back into Normal (D1 & D2 UP) or Telnet (D1 Up, D2 Down) mode for normal printing operation. 9.4.5 Printer Test Page Generate a Printer Test Page using the Print key on...

Apple/Macintosh Environments July 1998 9-7 M AC I N T O S H 4. Save the list and quit TeachText. 5. Double click on the Apple Printer Utility icon. 6. From the plodding menu, select Window and then Selector. 7. If there is a router on the network, select the appropriate zone for the printer. 8. Sele...

Unix Environment July 1998 10-1 UN I X 10 Unix Environment Refer to Kodak Printer/NIC Installation and ConÞguration Overview in Chapter 1 for overall conÞguration process steps and details. This chapter describes how to conÞgure the NIC and conÞgure a queue to submit Þles to a Kodak printer in a Uni...

Unix Environment July 1998 10-3 UN I X Note: The printer/NICÕs assigned IP address must be on the same local subnet as the Unix workstation. 4. Make a telnet connection to maintenance port 2002. (Type: telnet kodak 2002). 5. Press [!] and press [Enter]. Note: The following warning may appear: ÒEnter...

Unix Environment 10-4 July 1998 UN I X ¥ BSD systems ¥ System V Release 4 machines ¥ IBM RS/6000 ¥ TCP/IP packages for VMS ¥ TCP/IP packages for DOS ¥ IBM, HP, or DEC mainframe machines that run TCP/IP ¥ Microsoft Windows NT 3.5 ¥ OS/2 2.x with IBMÕs TCP/IP or LAN Server 2.x and above 10.2.1 Setting...

Unix Environment July 1998 10-5 UN I X 1. As root , create a local directory (i.e. Ò /tmp/kodak Ó) to load the software and then go to that directory. 2. Load the software from the disk by putting the diskette into a drive and typing: tar -xvf /dev/ <diskette drive device> 3. Type ./install.sh...

Unix Environment 10-6 July 1998 UN I X Enable LPD on System V systems by using SAM on HP/UX, admintool on Solaris, or any other system administration tool. To install the printer/NIC manually, use the following procedure. 1. Log in as root . 2. Create a dummy device in the /dev directory for use wit...

Unix Environment July 1998 10-7 UN I X 7. Enable the printer and accept these print job commands: enable <printer name> accept <printer name> 10.5 Printcap File Parameters Some commonly used entries in the printcap Þle are listed below. Note: The number of copies option with LPR ( LPR- n...

Printing July 1998 11-1 P R I N T I N G 11 Printing 11.1 PostScript and Raster Modes Kodak printers with the PS extension support both PostScript and raster printing. Models without the PS extension support only raster mode. Kodak provides PostScript drivers for PostScript mode printing and export m...

Printing 11-2 July 1998 P R I N T I N G If a Kodak driver is not available, you can use a generic PostScript driver or LaserWriter driver with the Kodak printer PPD Þle to generate PostScript output. 11.2 Changing between PostScript and Raster Printing Modes - Kodak 8xxx series Printers 1. Press Set...

Printing July 1998 11-3 P R I N T I N G 11.3 Changing From PostScript to Raster Printing Modes - Kodak DCP 9000/9300 Proofers 1. If the Indicator next to the ON LINE key is lit, then Press ON LINE on the display panel when READY appears in the panel to take the proofer OFF LINE. 2. Press MENU and SE...

Printing 11-4 July 1998 P R I N T I N G 11.4 Printing in PostScript Mode from Windows/DOS Systems 11.4.1 Printing from Windows To print from applications to a Kodak printer in PostScript mode: IMPORTANT: To avoid printing problems, make sure that ÒCtrlDÓ job termination is disabled in Printer PostSc...

Printing July 1998 11-5 P R I N T I N G LPR The example below illustrates how to use the lpr command to send a Þle to the printer from the DOS command line. In this example, the server name is server1, and the printer name is 8650. lpr -S server1 -P 8650 \fullpath\Þlename 11.4.3 Eliminating ÒCtrlDÓs...

Printing 11-6 July 1998 P R I N T I N G To select a Kodak printer in PostScript mode, select the Chooser from the Apple Menu Icon, then select the following: ¥ Active for AppleTalk ¥ AppleTalk zone ¥ Appropriate Kodak printer icon (Left Chooser Window) ¥ Appropriate printer (Right Chooser Window) 1....

Printing July 1998 11-7 P R I N T I N G 11.8 Printing from VMS Systems Printing with MultiNet on a VMS host The NIC works with a MultiNet stream queue on a VMS host. Invoke MultiNet's printer conÞguration utility to add a VMS print queue by entering the following command: multinet conÞgure/printers ...

Printing 11-8 July 1998 P R I N T I N G To print to a Kodak printer in raster mode: 1. Install a Kodak export module. 2. Select File>Export from Adobe PhotoShop. 3. Click on Network or Update to view and select printers that are in raster mode. 4. Select the printer OR queue associated with your ...

Troubleshooting July 1998 12-1 T ROUB L ESHOO T 12 Troubleshooting For easier referencing, troubleshooting steps are consistent with the following ÒNIC and Printer Installation/ConÞguration OverviewÓ steps outlined in theÓNIC Intro/OverviewÓ chapter : ¥ Step 1: Assess your Network/Printing Environme...

Troubleshooting July 1998 12-5 T ROUB L ESHOO T 12.1 Verifying Standalone Printer Functions If you are having trouble printing, Þrst verify that the standalone printer with no network interface connection operates correctly. Secondly, verify that the printer is conÞgured correctly when connected to ...

Troubleshooting 12-6 July 1998 T ROUB L ESHOO T 12.2 Verify Network Connectivity 1. When the printer Þnishes initialization and the front display/control panel displays the message ÒREADY,Ó check that the LEDs on the back of the printer operate correctly. ¥ The Yellow LED should illuminate and be in...

Troubleshooting July 1998 12-7 T ROUB L ESHOO T 12.4 Verify Application and Printer Parameters 1. Is there an error indication on the front control/display panel that the wrong ribbon is in use with a ÒLoad Oversize RibbonÓ message or the wrong paper with a ÒLoad PaperÓ message? If pressing the ÒPRI...

Troubleshooting 12-10 July 1998 T ROUB L ESHOO T 12.6 NT Installations 1. Check initial steps listed in this troubleshooting section to verify printer and parameters and connectivity. 2. On NT systems, you may encounter corruption of data when printing Þles over 5 Mbytes. Color bands may appear acro...

Troubleshooting July 1998 12-11 T ROUB L ESHOO T 12.7 AppleTalk Installations 1. Check initial steps listed in this troubleshooting section to verify printer and parameters and connectivity. 12.7.1 PostScript mode 1. Check the test print to verify that the preferred server is correct. 2. Are both th...

Troubleshooting 12-12 July 1998 T ROUB L ESHOO T 3. The appropriate printer must be selected for the export module. You can do this by opening the Export Module dialog box and checking the printer that is displayed in the Printer group box. If the correct printer is not displayed, click on Select; a...

Troubleshooting July 1998 12-13 T ROUB L ESHOO T This sends a packet to the Network Interface Card once every second. To abort the ping command, use Ctrl-C or the Delete key. If a message like the following appears, check the cable; and try it with another transceiver. No answer from <printername...

NIC Telnet July 1998 A-1 A PPE ND I X A Appendix A NIC Telnet If you are using TCP/IP protocol and have set up an IP address on the NIC, a NIC Telnet session can be established that provides complete control over all network protocols and related parameters. A.1 NIC Telnet Mode To invoke a Telnet se...

NIC Telnet A-2 July 1998 A PPE ND I X A Unix: Telnet <IP Address> <Port Address> Ex: Telnet 123.234.10.5 2002 A.3 Telnet Diagnostic and ConÞguration Commands C Ñ ConÞgure console (for status monitoring) D Ñ Display summary conÞguration parameters F Ñ Flash Þrmware load enable/disable H Ñ...

NIC Telnet July 1998 A-3 A PPE ND I X A Ethernet address:00 40 C8 00 0B 0B IP address:0.0.0.0 Console status monitoring: Off Network monitor password security: Off TCP sockets enabled. LPD enabled. Netware enabled. Microsoft Windows print services enabled. AppleTalk enabled. (type ÒNÓ in monitor to ...

NIC Telnet A-4 July 1998 A PPE ND I X A A.4.5 LÑLimit monitor network access by password Network monitor password security currently Off Monitor Security 1 (Off) 2 (On/New Password) 3 <enter> (don't change/continue) A.4.6 NÑNetwork protocols menu Network Protocols Menu: AÑAppleTalk options MÑM...

NIC Telnet July 1998 A-5 A PPE ND I X A NÑNetware options Netware enabled Print Server name used in SAP packets: KD000B0B Auto-sense frame type No primary server conÞgured NotiÞcation disabled Queue scan rate: 1 sec Netware Directory Services (NDS) enabled Tree name: Context: Modify?, yes or no (y o...

NIC Telnet A-6 July 1998 A PPE ND I X A Modify?, yes or no (y or n)?:n TCP/IP menu options: (S) Socket Options TCP Sockets enabled Modify?, yes or no (y or n)?:n TCP/IP menu options: (L) LPD Options LPD enabled LPD mode: DonÕt time out on printer error Modify?, yes or no (y or n)?:n TCP/IP menu opti...

Third Party Network Applications and Utilities July 1998 B-1 A PPE ND I X B Appendix B Third Party Network Applications and Utilities B.1 Windows 95 LPR Utilities Other vendors provide utilities that allow printing from Windows 95 using lpr. B.2 PC-NFS for Windows The NIC was designed as a direct ne...

Upgrading NIC Firmware and Resetting NIC to Factory Defaults July 1998 C-1 A PPE ND I X C Appendix C Upgrading NIC Firmware and Resetting NIC to Factory Defaults C.1 Upgrading the Flash EPROMs The Flash EPROM memory feature allows you to upgrade future Þrmware releases without opening the unit and r...

Upgrading NIC Firmware and Resetting NIC to Factory Defaults C-2 July 1998 A PPE ND I X C The NIC recognizes the Þle as a Þrmware image and loads it into memory instead of printing it. Once it is loaded and its checksum values are veriÞed, the NIC automatically resets itself and runs the new Þrmware...

¥ Enable Network Download ÑThe default state. ¥ Restart in Other Bank ÑThe only way to cause the older image to execute when the images differ. The effect is temporary. A power cycle will always run the newer image. Use this command to compare the old version to the new version to identify problems....

NIC Specifications July 1998 D-1 A PPE ND I X D Appendix D NIC SpeciÞcations D.1 RJ-45 Connector RJ-45 pinouts are shown below. ¥ Pin 1: Transmit data + ¥ Pin 2: Transmit data - ¥ Pin 3: Receive data + ¥ Pin 6: Receive data - Rx/Tx Crossover Cable If you want a direct RJ45 (10/100BaseT) connection f...

NIC Specifications D-2 July 1998 A PPE ND I X D D.2 Climate: Storage Temperature ¥ Minimum: -25¡ C ¥ Maximum: 75¡ C D.3 Electrical UTP Interface ¥ CAT 5 UTP ¥ Maximum cable length: 100 meters ¥ Data Rate: 10/100Mbps D.4 Regulatory Approvals ¥ EN55022 Class B ¥ EN50082-1 ¥ FCC Class A ¥ ICES-003 ¥ CE...

Technical Assistance July 1998 E-1 A PPE ND I X E Appendix E Technical Assistance If you have question about the printer or the NIC, consult the resources below. Retailer The retailer you purchased your printer from may be able to answer your questions. Kodak provides retailers with additional techn...

Index July 1998 Index-1 I NDEX INDEX Numerics 10BaseT 2-1 A about this guide 1-1adding printer, Windows for WorkGroups (3.x) 5-2 address IP 3-20, 3-28 name, changing 3-12 alternate bank image, restoring C-2AppleTalk 4-9application BOOTP server, messages 3-36 BOOTP, FastManage 3-29 discovery 3-21 dis...

Index Index-2 July 1998 I NDEX TCP/IP 3-22 utilities, FastManage 3-1 configuring bindery environment 4-1 Macintosh 9-1 mixed bindery 4-7 NDS environment 4-2, 4-7 NIC 1-8 Novell NetWare 4-9 print servers 1-9 printer on workstations 1-9 printing, Macintosh 9-5 Unix 10-1 Windows 95 6-1 Windows for Work...

Index Index-6 July 1998 I NDEX Q quick setup 4-2 R raster drivers 11-1 mode 1-10, 11-1 mode, changing to PostScript 11-2, 11-3 recovering from failed download C-2regulatory approvals D-2remote network spooling 10-4requirements FastManage hardware 3-2 software 3-2 resetting, factory defaults C-1, C-4...