Kenwood TS-130SE- Manuals

Page 2 - INTRODUCTION; satisfactory and dependable operation for many years.; A F T E R U N P A C K I N G :; The following explicit definitions apply in this manual:; CONTENTS

INTRODUCTION You are the owner of our latest product the new TS-130SE transceiver. Please read this in struction manual carefully before placing your transceiver in service. The unit has been carefully engineered and manufactured to rigid quality standards, and should give you satisfactory and depe...

Page 3 - TS-130SE SPECIFICATIONS

•mil • •Mill« iMin ••Mill •nuil* -«11111 • ■ •llll«•l|lll*•lllll»•llllll•«lllli•lllll*••llll»•*MII>•«IIM»‘l -lltlll•|||||l•llllll•lMll•>llllм•*llll»•ммl»•«|lMi*«NHl•«llHl•«l••l••l|lll»••мf•••tмн••mlll•*ml••«lм••мN•t•••mк TS-130SE SPECIFICATIONS ^M«••llll•••MII•■•tltll••lllll••IIM•• •inn• 11111...

Page 8 - vox; GAIN CONTROL; REMOTE CONNECTOR

® vox GAIN CONTROL This control adjusts VOX circuit sensitivity for both SSB and CW operation. (g) DELAY CONTROL This control is used to adjust the "Hold" time of the VOX cir cuit. Clockwise adjustment gives longer hold-time. (g) ANTI-VOX CONTROL This control is used to adjust the VOX syste...

Page 9 - RF ATT switch

SECTION 4. OPERATION Settings for reception Settings for transmission R F T u r n f u l l y clockwise A F T u r n f u l l y counterclockwise Turn CAR and MIC fully counter clockwise Microphone Fig. 4-1 Control and Switch Settings 4.1 RECEPTION First connect the antenna, microphone and key. Then, set...

Page 10 - SSB Operation

4.1.5. IF SHIFT CONTROL The IF SHIFT control is used to shift the passband of the IF filter without changing receive frequency. By turning this control in either direction, the IF passband is shifted as shown in Fig. 4-3. The IF SHIFT is effective in eliminating interference when the receive signal ...

Page 11 - • CW Operation; in; Power Meter

10k — 33 ki2 (depending on micropone used.) o------ ------------ • ---------- o from microphone O--------------- to the MIC connecter -O The MC-50 microphone is recommended (Microphone sen sitivity; — 55 ±3dB for approx. 5 cm distance to the mic.i • CW Operation 1 Set the MODE switch to CW and the ...

Page 12 - VOX OPERATION

Pointer should not deflect beyond ALC zone at signal peaks. Fig. 4-5 ALC Adjustment 4.3 VOX OPERATION 4.3.1. VOX SWITCH VOX (voice operated transmit) is used to switch the TS- 130SE into transmit mode by your voice. Depress the switch ON and speak into the microphone. The transceiver automatically s...

Page 13 - Contact station frequency; Your frequency; CW FILTER

A fixed channel is available for common use on all bands by installing a crystal in the socket on the AF-GAN unit (X49- 1110-01). The crystal frequency can be computed by the following formula; Crystal Frequency (MFIz) = 5.5 MFIz — X Frequency (MFIz). X = Band Switch frequency (1.5, 3.5, etc.) Cryst...

Page 15 - POWER CABLE

POWER CABLE red and white © black and gray 0 Connect the TS130SE power cable to the battery ter minals, with consideration to current requirements and noise prevention. The maximum current drawn by the TS-130SE reaches to between 18 and 20A when transmitting. Therefore, the cable should be made as ...

Page 16 - (4) Use Ignition Suppressor Cable or Suppressor Spark; FIXED STATION OPERATION

(1) Antenna Location Selection Since ignition noise is generated by the vehicles engine, the antenna must be installed as far from the engine as possible. (2) Antenna Matching In general, mobile antennas have a lower impedance than 50-ohm coaxial cable, resulting in a mismatch between the antenna an...

Page 17 - SECTIONS. ADDITIONAL INFORMATION; GENERAL INFORMATION

4.10 DIGITAL DISPLAY CALIBRATION (Fig. 4-14) 4.11 ANALOG DIAL CALIBRATION (Fig. 4-15) Connect the antenna and set the BAND switch to 10. Turn the main tuning dial to about "0" to receive the 10 MHz WWV signal. Adjust the dial until a low-frequency beat is heard. Next, turn on the CAL switch ...

Page 19 - MEMO

5.8 SERVICE Should it ever become necessary to return the equipment for repair, pack in its original boxes and packing, and include a full description of the problems involved. Also include your telephone number. You need not return accessory items unless directly related to the service problem. Tag...

Page 20 - SECTIONS. OPTIONAL ACCESSORIES

SECTIONS. OPTIONAL ACCESSORIES The following optional accessories are available for use with the TS-130SE. ■ Model PS-30 Regulated DC Power Supply The PS-30 is a regulated DC power supply with a large capacity. The output is 13.8 VDC/20A (Intermittent). Since terminals for 13.8 VDC/5A are also provi...

Page 22 - INTERNAL VIEWS

............................. ............................................................................................................................. . INTERNAL VIEWS .................................................................................................................. ...............

Page 24 - SCHEMATIC DIAGRAM

SCHEMATIC DIAGRAM .................................................................. ....................... . TS-130SE PLL UNIT (X50-1700-00) • M M » « ..... ... ^MM« • iMM«* «MW»- »MM* • 24

Page 30 - lATIC DIAGRAM

Page 31 - A product of; TRIO-KENWOOD CORPORATIOIM; TRIO-KEIMWOOD COMMUNICATIONS

Model TS-130SE Serial No. _____ Date of Purchase Dealer ----- A product of TRIO-KENWOOD CORPORATIOIM 1 7-5, 2-chome, shibuya, shibuya-ku Tokyo 1 50, Japan TRIO-KEIMWOOD COMMUNICATIONS 1111 West Walnut Street, CorriDton, California. 90220, U.S.A. TRIO-KENWOOO COMMUNICATIONS, GmbH D-6374 Steinbach TS,...