Page 2 - THANK YOU; We are grateful you have chosen; for your land; NOTICES TO THE USER; It is important that the operator is aware of, and; PRECAUTIONS; KENWOOD
THANK YOU We are grateful you have chosen KENWOOD for your land mobile radio applications. NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ R...
Page 4 - ii; Information concerning the battery pack:; Do not disassemble or reconstruct battery!
ii Information concerning the battery pack: The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters...
Page 5 - iii; Do not jar or throw the battery!
iii • Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemica...
Page 6 - iv; Do not touch a ruptured and leaking battery!
iv • Do not touch a ruptured and leaking battery! If the electrolyte liquid from the battery gets into your eyes, wash your eyes with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery ...
Page 7 - CONTENTS; UNPACKING AND CHECKING EQUIPMENT; SUPPLIED ACCESSORIES; stopper
1 CONTENTS UNPACKING AND CHECKING EQUIPMENT .........................1PREPARATION .........................................................2ORIENTATION ..........................................................7PROGRAMMABLE AUXILIARY FUNCTIONS........................8BASIC OPERATIONS ..................
Page 8 - PREPARATION; INSTALLING THE CHANNEL STOPPER; Insert the channel stopper.
2 PREPARATION INSTALLING THE CHANNEL STOPPER For transceivers with less than 16 channels, insert a Channel stopper. 1 Set the Channel selector to channel 1, then pull the Channel selector knob off the transceiver. • If the Channel selector is not positioned at channel 1, the Channel selector knob ma...
Page 9 - INSTALLING/ REMOVING THE BATTERY PACK; Align the battery pack with the back; INSTALLING THE BELT CLIP
3 INSTALLING/ REMOVING THE BATTERY PACK ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly together until the...
Page 10 - CHARGING THE BATTERY PACK; Plug the AC adapter cable into the jack located on the rear
4 CHARGING THE BATTERY PACK The battery pack is not charged at the factory; charge it before use. ATTENTION: Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger. 1 Plug the AC adapter cable into the jack located on the rear of the charger. 2...
Page 11 - When charging is completed, the indicator lights green.
5 5 When charging is completed, the indicator lights green. Remove the battery pack or the transceiver from the charging slot of the charger. • It takes approximately 3 hours to charge the battery pack.• When the charger will not be used for a long time, unplug the AC adapter from the AC outlet. Not...
Page 13 - ORIENTATION; Channel Annunciation:
7 ORIENTATION Channel selector Rotate to change the operating channel. • Channel Annunciation: When changing channels, the transceiver will announce the newly selected channel number (if enabled by your dealer). LED indicator For the LED indicator status, refer to page 11. Power switch/ Volume contr...
Page 14 - PROGRAMMABLE AUXILIARY FUNCTIONS; PTT
8 PROGRAMMABLE AUXILIARY FUNCTIONS Your dealer can program the Side 1 and Side 2 keys each with one of the following functions. Note: The duration of pressing a key to activate a function is dependent on your dealer setting. Your dealer may have set some keys to be held down for a short duration ins...
Page 16 - Press this key to start scanning the transceiver channels.; Press this key to send a status.
10 ■ Scan Press this key to start scanning the transceiver channels. ■ Scan + Temporary Delete Scan pauses at an undesired channel, you can remove that channel from the scanning sequence by press or hold this key. ■ Scrambler The Scrambler function allows you to hold a conversation in complete priva...
Page 17 - BASIC OPERATIONS
11 BASIC OPERATIONS 1 Turn the Power switch / Volume control clockwise to switch the transceiver power ON. • A beep sounds if enabled by your dealer. 2 Press the key programmed with the [Monitor] or [Squelch Off] function to hear background noise, then rotate the Power switch / Volume control to adj...
Page 18 - Channel
12 VOICE OPERATED TRANSMISSION (VOX) VOX operation allows you to transmit hands-free. This feature must first be activated by your dealer, and can only be used if you are using a supported headset. This function can be turned off for specific channels by your dealer.To activate VOX and set the VOX G...
Page 19 - BACKGROUND OPERATIONS; BATTERY SAVER; LOW BATTERY WARNING; switch will; switch to stop the tone.
13 BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer prevents callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is 1 minute), transmission will stop and an alert tone will sound. To stop the tone, relea...
Page 20 - SIGNALING; or; BEGINNING/ END OF TRANSMISSION SIGNAL; switch and the End of Transmission ID signal is
14 SIGNALING ■ QT/ DQT The Encoder/Decoder function uses QT/ DQT to segregate talk groups, so users only hear calls from their own group. ■ DTMF A DTMF PTT ID is included for dispatch operations or simple remote control applications.The DTMF decode capabilities include Selective Call ID, Transpond w...
Page 21 - ADDENDUM: Transceiver Password; ADDENDA : Mot de passe émetteur-récepteur; Répétez les étapes 1 et 2 pour les positions 2 à 4 du sélecteur de; SUPLEMENTO: Clave del transceptor; Repita los pasos 1 y 2 en las posiciones 2 ~ 4 del selector de
ADDENDUM: Transceiver Password If your transceiver is password protected, the LED will light blue when you turn the transceiver ON. Enter the password (up to 4 digits) using the following procedure.1 Set the Channel selector to position “1”.2 Press the Side 1 or Side 2 key to enter the first digit. ...