Kenwood Preset Remote Control- Manuals

Page 3 - Begistering setup podes forpther components; Now; to use the displagoperatimk^; iill; Фш

The remote control supplied with this receiver is also capable of controlling components from a variety of manufacturers once you register the appropriate setup codes into the remote contrpi unit. Refer to "Remote operation of other components" for de tails about the operations available f...

Page 6 - Preparing for automata operatiom; ili

I Preparing for automata operatiom '$ (MACRO play) The macro play function allows you to set the remote to control several components in succession. After completing this setup, you can perform a series of operations automatically. Enter the setup codes for the components you want to control beforeh...

Page 7 - To delete the setup code

; GéWng ìhé most from your remote comtqf; Executing an^ To delete the setup code iVIACRO During opration, make sure you start the next step within 8 seconds of completing the previous one. if more than 8 seconds eiapses between any two steps, press the display operation key so that the display appea...

Page 8 - storing the remote control cord of the other; iiitt; ■lete

1 storing the remote control cord of the other " component^ The remote control unit can store the remote control cord ot the other components and you can operate the other components from the remote control unit. The remote control cord is stored on the key or memory of the remote control unit. ...

Page 9 - Restoring the original factory

© Press the a / t keys to select the location. 1 Bitei-idl “ E-;rtend5 are available. © Press the {Enter] key. « The remote contro! is ready for receiving the remote control code. B-'cti'endi IClr Exit J ® Press the key of the same operation that you want to store. • The remote code is send to the r...

Page 10 - PIsplaYlng the CD TEXT data; IS

10 PIsplaYlng the CD TEXT data ,'сйя^/J.; ■ [^¡' ,'fj' When you connect a KENWOOD CD player (CD-425M, CD-4700M, CD- '426OM, DPF-J6030), you can display the CD TEXT data in the display of the remote control unit. Before operation, regiser the setup code of the CD piayer. O Press the [Text] key. » The...

Page 11 - COO ODC3; QD; oca O DD0; goo o ca

, ReMoté'<úfl§Miúrí^^^ You can operate other components by pressing keys or using the display.The setup code for each component must be entered beforehand, RC-CI3 When you operate by using the keys ® Press the MUSIC, MOVIE, or TV key to select the component you want to control. © Press the keys c...

Page 12 - eoo ODDS; cm; m TM CC3; ED

Remote operation of other components TV operations CHANNEL + CHANNEL - QD eoo ODDS fZj VOLUME + >oi VOLUME - KK] Cursor ENTER cm ra C> DCD o (Mute) Numeric keys <ss> CD ^ FUNCTION SHIFT commands INPUT SEL.TV SELECT AUDIO Display operation 01: 02:>12 03: Wide04: Picture in Picture 05: ...

Page 13 - ii; sss

^V'.;.■;;;■:■'■■■■: v,ü;r,r';: ,'i .V Wf j( 1*^ i#V*!-* W;---V'v'-''-'^i !•'; ■ >!■ ■ :;■ DSS receiver operations ii säte CHANNEL + CHANNEL■ Cursor ENTER Ä><S>c!b <S>cr>cz> CX>Ö<S ® cz:>'^' Numeric keys tef i; ^ ÍB B!> FUNCTION SHIFT commands INPUT SEL. SELECT AUD...

Page 14 - In case of difficulty; Mi

In case of difficulty Mi Remote control unit Cause , 1 Remedy The battery indicator flashes during operation. > The batteries are nearing exhaustion. ® Replace with new batteries to presen/e the currently registered setup information. Subwoofer volume cannot be adjusted. « Subwoofer is OFF. “ Tu...